Door Check Link Rod End Stop
p/n: 20-1640-70
This Door Check Link Rod End Stop is designed from the original part for superior fit and function. This door stop fits between the door and body to limit the swing opening of the door preventing overtravel. Door check arm and bumper. Enough for one door.
Tie Rod Dust Covers
p/n: 20-2484-36
This Tie Rod Dust Cover, drag link seal, is sold as a four (4) piece set. The seals are designed from originals for proper fitment.
Fuel Neck Grommet
p/n: 20-2177-39
Grommet, fuel filler neck. Fully molded rubber with small retaining lip. Three and five eighths inch (3-5/8") outside diameter by two and nine sixteenths inch (2-9/16") inside hole diameter.
Cowl Firewall Grommet
p/n: 20-1560-20
This Cowl Firewall Grommet fits into the upper section of the firewall for the main wiring harness. Also used to run the dash wires on the firewall and through the firewall.
Upper Engine Mount
p/n: 20-1538-11
This Front or Rear Upper Engine Mount reproduction is designed from the original part for superior fitment and durability. This mount fits between the engine and chassis to support the engine and reduce harmonic vibrations.
Lower Engine Mount
p/n: 20-1539-11
This Lower Engine Mount is designed from original part for correct fitment and function. Rubber coated over a metal core for durability and proper engine vibration isolation.
3/16" x 5/8" Fabric Hood Lacing
p/n: 70-4768-42
This 3/16" x 5/8" Fabric Hood Lacing is made of a high-quality original style woven cotton. Available by the foot to accommodate any job.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Wiper Transmission Gasket
p/n: 20-1609-53
Seal, wiper pivot shaft to roof or cowl. Small type. Replaces factory #11A-17541. Note: this part is used as a wiper pivot shaft to roof in 1937-1939. It is used as a wiper pivot shaft to cowl in 1941-1948.
Door Handle Gaskets
p/n: 20-2100-69
This Door Handle Gasket pair is designed from the original part for superior fitment, finish and function. Gaskets have a proper raised edge to center the handle on, so it fits correctly.
Engine Mount Washer
p/n: 20-0442-11
This Front Upper Engine Mount Washer is made of steel. The large upper engine mount insulator sits in this special washer. Fits all Ford 6 cylinder and Flathead V-8 models.
Door Handle Gaskets
p/n: 20-2101-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. Manufactured from paper just as original.
Door Jamb Bumper
p/n: 20-2366-71
This Door Jamb Bumper is a quality reproduction of the original factory part. This rubber bumper mounts into a slot in the door jamb to cushion the door closure. Two (2) required per door.
Choke and Throttle Dash Grommets
p/n: 20-0347-41
This Choke and Throttle Dash Grommet pair mounts in the dash where the choke and throttle rods pass through the dash to keep rods from rattling.
1-1/4" Body Hole Plug
p/n: 20-1039-21
This Body Hole Plug is designed from the original part for superior fitment, finish and function. This plug is made from high quality EPDM dense rubber to provide excellent durability. This body plug covers a sheet metal hole that is one and one fourth (1-1/4") inches in diameter.
Choke, Throttle and Starter Wiper Motor Grommet
p/n: 20-1561-20
This Choke, Throttle or Wiper Motor Grommet is designed from the original part for superior fitment and usage. A multi-purpose grommet, it fits into the vehicles firewall to provide a secure passthrough for the mechanical choke, throttle rod or wiper motor wiring.