Body Mounting Pad
p/n: 70-0298-48
Pads, body mounting for front bracket, right and left. Three eighths (3/8) inch by two and three fourths (2-3/4) inch by four (4) inches with two (2) collars and retaining rings. Two (2) required per car.
Brake shaft stop bumper
p/n: 70-0271-24
Bumper, brake rocker shaft lever stop. Two (2) used per car. Also used as door side bumper for some 1927-31 Cadillacs.
Cadillac Motors pedal pad
p/n: 70-0076-22
Cadillac Motors pedal pads. Authentic straight diamond pattern. Especially good copy, fine detail.
Cadillac V-8 Pedal Pad
p/n: 70-0148-22
Cadillac V-8 pedal pads, clutch and brake. Another rare one we finally found to copy. Superior copy.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Chrome Fender Welting - 50ft
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Coil wire sleeve
p/n: 70-0109-21
Sleeve, coil wire to distributor. Fluted to match upper water hoses rubber only. V-12 & V-16 with coils mounted in radiator, V-8 with coils mounted horizontally on brace rods.
Convertible Top Rest Block
p/n: 70-0069-67
Pads, convertible top rest for rear deck. Two heights as original for inner and outer positions. Four (4) piece set.
Door Bumper
p/n: 70-1157-71
Pad, door jamb (door side bumper).Some bodies using escutcheons around pads.Length: 1.5625 inches. Width: 1.1875 inches.
Door Bumper
p/n: 70-1154-71
Pad, door jamb, rear door fender cut out. One and one half (1-1/2) inch outside diameter, seven eighths (7/8) inch plug.
Door Check Link Rod End Stop
p/n: 70-0325-70
A quality Door Check Link Rod End Stop for rod type door check mechanism. One (1") inch diameter by three-eighths (3/8") inch thick with five-sixteenths (5/16") inch hole.
Door Check Link Rod End Stop
p/n: 70-0326-70
End stop and pad, door check link rod. Rubber with embedded steel plate, five sixteenths (5/16) inch diameter thread. Most models with rod type door checks.
Door Handle Ferrule
p/n: 70-0111-69
A Ferrule for three fourths (3/4") inch outside door handles. Chrome plated brass. Used for outside door handle or outside trunk handle.
Door Handle Grommet
p/n: 70-0009-69
Grommet, for outside door handle ferrule (our #70-0111-69, ordered separately). Molded rubber with cloth covering per original.
Engine Mount Cushions
p/n: 70-0300-11
These Engine Mount Cushions are used as an intermediate engine mount for support bolts. Split in half if needed at installation. A four (4) piece set.
Fender Welting 1/4" Bead - 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty-five (25) foot roll. Typically used to attach two (2) fenders to body.
Fender Welting 1/4" Bead - 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body.
Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Fender Welting with 3/16" Bead - 50ft
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Ferrule Installing Tool
p/n: 70-0662-69
Installing tool, door and trunk handle ferrule. For cars and trucks using door and trunk handle ferrules such as our #70-0111-69.
Front and Rear Door Bumper
p/n: 34-0025-42
High quality steel core Front and Rear Door Bumper for front and rear body hinge pillar. Mounted by screw. For auxiliary use only where needed to prevent door rattles. Replaces factory #372341.
Front Apron Crossbar Grommet
p/n: 70-1130-45
Grommets, front splash apron crossbar.Width: 3.5 inches. Height: 3.6875 inches.
Front Bumper Grommet
p/n: 70-0103-28
Grommets, front bumper. Theses are for the round, tubular bumper support.
Golf Bag Door Weatherstrip
p/n: 70-0118-85
This Golf Bag Door Weatherstrip is designed from the original part for superior fitment and seal. This seal mounts directly to the golf bag door.