Side Window Run Channel
p/n: 70-1169-58
Channel, side window, pre-flocked, 9/16" wide to accommodate metal frame side window. Available by the foot.
Handbrake Lever Anti-Rattle
p/n: 60-0531-24
Spacer, anti-rattle, handbrake lever sector rod, between release rod and handbrake lever.Width: .6875 inches. Height: .6875 inches.
Front and Rear Door Bumper
p/n: 34-0025-42
High quality steel core Front and Rear Door Bumper for front and rear body hinge pillar. Mounted by screw. For auxiliary use only where needed to prevent door rattles. Replaces factory #372341.
Side Window Lower Bump Stop
p/n: 70-0110-62
This Side Window Lower Bump Stop is designed from the original part for an authentic fit, finish, and function. Requires two (2) stops per window.
3/16" x 3/4" Fabric Hood Lacing
p/n: 70-2221-42
This 3/16" x 3/4" Fabric Hood Lacing is made of a high-quality original style woven cotton. Available by the foot to accommodate any job.
1/8" x 7/8" Fabric Hood Lacing
p/n: 60-0578-42
This 1/8" x 7/8" Fabric Hood Lacing is high quality original style woven cotton hood to cowl lacing. This lacing has the slot to install a wire insert or fasten with rivets if so found originally. Available by the foot to accommodate any job.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Door Bumper
p/n: 70-1158-71
Pad, door jamb, (door side bumper).Length: 1.25 inches. Width: 1.125 inches.
Door Check Link Rod End Stop
p/n: 70-0326-70
End stop and pad, door check link rod. Rubber with embedded steel plate, five sixteenths (5/16) inch diameter thread. Most models with rod type door checks.
Starter Button Cover
p/n: 60-0358-21
Cover, starter rod button, round slip over type. One and seven sixteenths (1-7/16) inch outside diameter. Good copy with bow tie center.
Door Handle Ferrule
p/n: 70-0111-69
A Ferrule for three fourths (3/4") inch outside door handles. Chrome plated brass. Used for outside door handle or outside trunk handle.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Starter Button Cover
p/n: 60-0166-21
Cover, starter pedal button. Rubber slip over type for old metal. Two (2) inch outside diameter. If car doesn't have old metal, see our #60-0322-21.
Firewall Grommet
p/n: 60-0010-45
This Firewall Grommet is the oblong four (4) hole style. The grommet fits the steel retainer for the throttle and choke cables, and the oil and temperature lines.
Steering Column Spacer
p/n: 60-0563-32
Spacer, steering column to dash at U-clamp.Length: 2.50 inches.
Accelerator Rod Button Cover
p/n: 60-0357-40
Cover, accelerator rod button. Round slip-over type. Good copy with bow tie center. Height: .4375 inches.
Cowl Vent Gasket
p/n: 60-0131-54
Gasket, cowl vent. One fourth (1/4) inch by five sixteenths (5/16) inch, for five (5) inch by fifteen (15) inch top cowl vent. Sponge type.Width: 15.
Starter Button
p/n: 60-0322-21
Starter button, push on replacement to rod. Two (2) inch outside diameter.
Rumble Seat Lid Corner Pad
p/n: 70-0120-87
Pad, rumble seat lid corner, Compare with our #60-0191-87. Length: .75 inches.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Brake and clutch shank seal
p/n: 60-0019-24
Seal, brake and clutch pedal shank to floorboard. Single bellows rubber cup, seals air drafts around pedals.
Rumble Seat Lid Bumper Pad
p/n: 60-0191-87
Bumper pad, rumble seat lid, upper corners. Compare with our #70-0120-87.Width: 1.0 inches. Height: 1.125 inches.
Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.