Suspension Bushing
p/n: 30-0386-36
Bushing and pin assembly cartridge. Inlox type, front wheel lower support arm inner pin. Shipped with instructions for reinstalling.Length: 5.75 inches.
Engine Mount Service – Revulcanization Only
p/n: 30-0375-11
This Revulcanization Service Only is designed to restore your rear engine support at transmission housing to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Windshield Gasket
p/n: 30-0281-50
This Windshield Gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit.
Front Suspension Bumper
p/n: 30-0490-32
Bumper, front suspension (inside of coil spring). Made with three five sixteenths (5/16) inch studs as original.
Front Door Vent Window Weatherstrips
p/n: 30-0018-55
This four (4) piece Front Door Vent Window Weatherstrips contain the upper and lower seals that cover the top, front, and bottom of the vent window. All of the pieces are designed from original parts for a precise, factory fit.
Front Suspension Bumper
p/n: 30-0228-32
Bumper assembly, front suspension inside coil spring, with five sixteenths (5/16) inch threaded studs as found originally.
Front spring bushing
p/n: 30-0393-32
Bushing assembly, front wheel support; upper and outer. Inlox type cartridge bushing assembly.
Side Roof Rail Weatherstrip
p/n: 30-0031-65
Weatherstrip, side window. Fits metal channel. Made of high-quality EPDM rubber. Twelve (12) foot strip.
Transmission Stabilizer
p/n: 30-0252-24
Stabilizer, fore and aft transmission to frame. A factory service part used to remedy clutch chatter. Steel core as original.Length: 7.50 inches.
Engine Mount Service – Revulcanization Only
p/n: 30-0185-11
This Revulcanization Service Only is designed to restore your Rear Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Front suspension bushing
p/n: 30-0239-32
Bushings, front suspension torque arm. Necessary for proper front end geometry.
Door Lock Striker Revulcanization Service
p/n: 30-0398-71
This Revulcanization Service Only is to restore your front or rear Door Lock Striker to it's like new original condition. Service requires your old metal striker core. Please call or email for more service details and ordering.
Front spring bumper
p/n: 30-0227-32
Bumper assembly, front spring rebound (upper arm). Steel core, with treaded stud just like original.
Hood Corner Pad
p/n: 30-0011-42
Pads, hood front corners, large type. Molded right and left with metal cores and double tab retainers.Length: 3.1875 inches. Width: 2.125 inches.
Door Weatherstrip
p/n: 30-0051-73
Weatherstrip, door edge. Retained by metal clips. (For clips, see our #70-0391-73). Fifteen (15) feet per strip.
Axle Rebound Pad
p/n: 30-0371-32
Bumper, rear frame to axle rubber. Two (2) per car.Length: 5.1875 inches. Width: 2.0625 inches.
Gearshift Boot
p/n: 30-0178-24
Boot, gearshift cover. For cane shifts only. Length: 4.0 inches. Width: 3.0 inches. Height: 5.125 inches.
Hood Corner Pad
p/n: 30-0010-42
Pads, hood rear corners. High quality rubber with metal core as original.Length: 3.4375 inches. Width: 1.875 inches.
Accelerator Pedal Service
p/n: 30-0400-41
Revulcanization Service Only for Black Rubber Accelerator Pedal Pad. Includes new ball sockets as original, with correctly detailed tread pattern.
Rear Bumper Grommet
p/n: 30-0067-29
Grommets, rear bumper. Length: 4.3125 inches. Width: 2.6875 inches.
Engine Mount Pad
p/n: 30-0238-11
This Engine Mount Pad pair is used as a support cushion at the timing gear cover. Correct design and rubber compound. Sold only in pairs. One (1) pair required per car.
Chrome Fender Welting - 50ft
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Fender Welting 1/4" Bead - 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body.
Fender Welting with 3/16" Bead - 50ft
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.