Hood to Fender Bumper
p/n: 30-0304-42
This Hood to Fender Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure. Six (6) required per car.
Accelerator Hinge Grommet
p/n: 30-0539-41
Grommet, accelerator pedal hinge to floorboard. Length: 3.50 inches. Width: 2.50 inches.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Body Mounting Pad
p/n: 70-1429-48
Pad, body mounting. Fully molded rubber with metal core and rubber locating collar. Also used for radiator cradle to frame. Eight (8) to ten (10) required per car. Two and one fourth inch (2 1/4") outside diameter by one and one sixteenth inch (1 1/16") l
Power brake carpet grommet
p/n: 70-3147-24
Grommet, carpet. Floor front carpet grommet use for power brake hole.
Firewall Seal
p/n: 70-1600-36
Grommet, power steering lines to frame.Length: 2.75 inches. Height: .75 inches.
Power window switch bezel pad
p/n: 70-2136-21
Mounting pad, power window die cast bezel. Used under single window switch, typically found on front passenger door and rear windows.
Firewall Seal
p/n: 70-1599-36
Grommet, power steering lines to air duct.Length: 3.3125 inches. Width: .75 inches.
5" Wide Bow Drill Cloth Tape
p/n: 70-1175-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Power Window Switch Bezel Pad
p/n: 70-2137-21
Mounting pad, power window die cast bezel. Used under 4 way switch, typically found on drivers door.Width: 2.0 inches.
Brake Pedal Pad
p/n: 70-2640-22
This reproduction Brake Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. Replaces original brake pedal cover pads on models with power brakes. Detailed and finished to match the original appearance.
Antenna Mount Pads
p/n: 70-2264-21
This Antenna Mount Pad pair is designed from the original part for superior fitment and seal. For rear mounted twin (dual) antennas. See our 32-0390-21 for insulating Antenna Grommet pair.
2" Wiring Harness Firewall Grommet
p/n: 70-1724-20
This Wiring Harness Firewall Grommet is used to run the main wiring harness through the firewall. Designed from the original part for superior fit and seal.
2" Firewall Grommet
p/n: 70-1725-20
This Firewall Grommet is used to run the windshield washer hose and antenna wiring through the firewall. Designed from the original part for superior fit and seal.
Firewall Grommet
p/n: 30-0456-20
This Firewall Grommet is used for the heater core at the firewall. Designed from the original part for superior fit and seal.
Parking Light Gasket
p/n: 70-2023-15
Gasket, parking light housing. Die cut from durable black sponge-cell rubber. One (1) pair needed per car.Length: 11.375 inches.
Hood to Cowl Weatherstrip
p/n: 30-0527-42
Weatherstrip, hood to cowl. Overall thirty seven (37) inches long.
Windshield weatherstrip
p/n: 70-1535-52
Weatherstrip, windshield garnish molding on lower windshield post. Molded rubber replacement for #469222-3.
Front Stabilizer Bushing
p/n: 30-0298-33
Bushings, front stabilizer rod end. One (1) pair required per car. Fully molded rubber.
Coil Wire Sleeve
p/n: 70-2052-21
Boot, spark plug wire, at spark plug. All original textures and details.Length: 2.0 inches.
Beltline Weatherstrip
p/n: 30-0300-58
Window felt inner and/or outer. Flexible, pile lined, rubber covered, with stainless bead. Available in 3ft pair.