Fender Welting 1/4" Bead - 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty-five (25) foot roll. Typically used to attach two (2) fenders to body.
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft. lengths.
Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Door Weatherstrip
p/n: 60-0114-73
Weatherstrip, door bottom, sponge constant section, solid skin surface, superior quality. Sold in six (6) foot strips only.Length: 72.0 inches.
Front Stabilizer Bushing
p/n: 60-0088-34
This Front Stabilizer Bushing pair is fully molded from EPDM dense rubber to ensure durability. Used to connect the stabilizer bar to the vehicle frame. Two (2) required per car.
Fuel Neck Grommet
p/n: 60-0040-41
Grommet, fuel filler neck. Fully molded rubber, slightly angled with retaining flange. Three and five sixteenths inch (3-5/16") outside width by three and one half inch (3-1/2") outside length by two and one eighth inch (2-1/8") inside hole diameter.
Headlight Mounting Pad
p/n: 70-0201-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. This pad acts as the headlight adjusting collar. Sold as a pair.
Cowl Vent Hose
p/n: 60-0457-54
Hose, cowl vent drain. Seems to be correct for some models rather than our #50-0259-54.
Horn Button Contact Set
p/n: 60-0492-21
This is a three (3) piece Horn Button Contact set which is designed from the original part for superior fitment and function. Renews the operation of the steering wheel horn blowing ring.
License Light Mounting Pad
p/n: 60-0074-17
Mounting pad, license light. Three and one eighth (3-1/8) inch by eight and seven eighths (8-7/8) inch. Fully detailed.Length: 8.875 inches.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Backup Light Mounting Pad
p/n: 60-0072-17
Mounting pads, back up lights, elliptic, sharp beaded edge. One and five sixteenths (1-5/16) inch by two and seven eighths (2-7/8) inch.Length: 2.
Cowl vent weatherstrip
p/n: 70-0143-54
Gasket, cowl vent. Perfect copy of original, not a sponge substitute, top quality material.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Hood to Cowl Weatherstrip
p/n: 60-0090-42
This Hood to Cowl Weatherstrip is extruded from a high quality dense rubber for a durable and proper seal. This pair comes with pre-drilled holes for easy installation.
Center Division Bar Chrome Molding Retainer
p/n: 70-0373-51
Center Division Bar Chrome Molding Retainer for outside windshield center post stainless molding. Use with original stainless molding and clips. Length: 15-1/2 inches. Width: 1-1/4 inches.
Gravel Shield Bumper Set
p/n: 60-0146-30
This Gravel Shield Bumper Set is used as a rear bumper deflector. Also used between the radiator grille and the lower panel. Two (2) required per car. Designed from the original part for superior fitment and seal.
Parking Light Lens Gasket
p/n: 60-0207-17
Gasket, parking light lens. Top quality one eighth (1/8) inch sponge.Length: 5.50 inches. Width: 1.75 inches.
Taillight Lens Gasket
p/n: 60-0100-15
Gasket, taillight lens.Length: 5.125 inches. Width: 1.875 inches.
Starter Button
p/n: 60-0322-21
Starter button, push on replacement to rod. Two (2) inch outside diameter.
Brake and Clutch Pedal Bumpers
p/n: 60-0104-24
Bumpers, brake and clutch pedal shank, rides under floorboard. One and one eighth (1-1/8) inch clearance for pedal shaft. Compare with part 60-0579-24.
Door Check Link Rod End Stop
p/n: 70-0479-70
End nut, check link (rubber bar with steel bar insert). Three fourths (3/4) inch by three fourths (3/4) inch by two (2) inch threaded five sixteenths (5/16) inch. (For round stop nut, see our #70-0326-70).
Steering column seal
p/n: 60-0478-36
Seal, steering column at toe board, for steering column housing and shifter control shaft jacket. Top quality sponge rubber, accurately cut.
Starter Button Cover
p/n: 60-0166-21
Cover, starter pedal button. Rubber slip over type for old metal. Two (2) inch outside diameter. If car doesn't have old metal, see our #60-0322-21.
Brake Master Cylinder Push Rod Boot
p/n: 60-0180-24
This Brake Master Cylinder Push Rod Boot is made from high-quality Nitrile rubber for a precise, factory like fit for your classic vehicle. Manufactured to OEM specifications to install for an authentic fit and finish.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Door Handle Ferrule
p/n: 60-0389-69
Ferrule, outside door handle. Chrome with rubber sleeve. Two (2) piece set includes one (1) chrome piece and one (1) rubber piece. Enough for one door.
Trunk handle bezel and grommet
p/n: 60-0526-87
Bezel and grommet, trunk handle and license light body.
Exhaust Support Grommet
p/n: 60-0031-13
This Exhaust Support Grommet is designed from the original part for superior fitment and usage. The OEM direct fit application is as a rear and middle muffler exhaust support hanger.
2" Firewall Grommet
p/n: 70-0158-21
This Firewall Grommet is used to run the ignition switch conduit through the firewall. Designed from original parts for excellent workmanship.
1-11/16" Firewall Grommet
p/n: 60-0057-21
This Firewall Grommet is used to run the wiring harness through the firewall. Designed from original parts for excellent workmanship.
Window Stop Stem Bumper
p/n: 33-0675-62
Cushion (stem bumper), window stop, lower. For front and rear door, rear side and quarter windows as required.
Spark plug retaining ring
p/n: 30-0352-21
Retaining ring, spark plug wire. Two (2) per car.Chevrolet 1935-48 Retaining ring, spark plug wire. Two (2) per car. All models.
Ferrule and Grommet Set
p/n: 70-0597-69
This Ferrule and Grommet Set for the outside door handle is cadmium plated ferrule with rubber sleeve. Two (2) piece set for one (1) door.
Starter Pedal Bellows
p/n: 60-0210-21
Bellows, starter pedal shaft to floorboard. Three eighths (3/8) inch top hole with three (3) inch height.Width: 2.875 inches. Height: 3.0 inches.
Clutch and Brake Pedal Bump Stops
p/n: 70-4805-24
This Clutch and Brake Pedal Bump Stop pair is designed from the original part for superior fitment, finish and function. These rubber bumpers help align your brake and clutch pedals in the correct position, while also preventing rattles and squeaks.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Gearshift Bushing
p/n: 60-0237-24
This Gearshift Bushing is fully molded and designed from the original part for superior fitment and seal. This bushing is made from high-quality EPDM dense rubber to provide excellent durability. Designed for the gearshift shaft lever, large type.
Shock Absorber Bushing
p/n: 60-0521-33
Bushing, shock link, rear. Four (4) per car, for double acting shocks.Width: .875 inches. Height: .50 inches.
Steering knuckle support seal
p/n: 60-0089-32
Seal, steering knuckle support, upper. Four (4) per car.
Door Lock Mounting Pad
p/n: 27-0020-69
Mounting pad, door lock cylinder, right and left.Length: 1.6875 inches.
Steering Column Gearshift Vacuum Boot
p/n: 60-0555-24
This Steering Column Vacuum Cylinder Boot is designed from the original part for superior fitment, finish and function. An excellent duplicate of original.
Steering Gear Pitman Arm Bushing
p/n: 60-0105-36
This Steering Gear Pitman Arm Bushing is designed from the original part for superior fitment and function. Fully molded with steel core.
Front and Rear Door Bumper
p/n: 34-0025-42
High quality steel core Front and Rear Door Bumper for front and rear body hinge pillar. Mounted by screw. For auxiliary use only where needed to prevent door rattles. Replaces factory #372341.
Window Stop Stem Bumper
p/n: 33-0540-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and seal. Designed as a window stop cushion for front and rear door, rear side and quarter windows as required.
15/16" Trunk Weatherstrip
p/n: 70-0490-85
This Trunk Weatherstrip is made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Side Window Roller
p/n: 70-0117-62
This Side Window Roller, anti-rattle roller, is manufactured using EPDM dense rubber to replace the original perfectly. The roller fits both styles of brackets.