Running Board Edge Seal
p/n: 30-0169-44
Liner, running board to body, (side apron to body seal). Set consists of two (2) pieces seven (7) foot long. One (1) inch width is after fold over.
Front Bumper Grommet
p/n: 30-0001-28
Grommet, front bumper. Molded right and left with hollow construction as found on original.Length: 4.0 inches. Width: 2.25 inches.
Windshield Division Bar Gasket
p/n: 30-0104-52
Gasket, windshield glass center division. Molded with screw holes and end pilots. Replaces #236866.
Rear Bumper Grommet
p/n: 30-0006-29
Grommets, rear bumper.Length: 3.625 inches. Width: 3.3125 inches.
Axle Rebound Pad
p/n: 30-0371-32
Bumper, rear frame to axle rubber. Two (2) per car.Length: 5.1875 inches. Width: 2.0625 inches.
Engine Mount Service – Revulcanization Only
p/n: 30-0543-11
This Revulcanization Service Only is designed to restore your Engine Mount Stabilizer Bracket to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Front suspension bushing
p/n: 30-0239-32
Bushings, front suspension torque arm. Necessary for proper front end geometry.
Side Roof Rail Weatherstrip
p/n: 40-0095-65
Weatherstrip, convertible top to side windows. Fifteen sixteenths (15/16) inch by five eighths (5/8) inch. Sold in twelve (12) foot strips only.
Windshield Gasket Weatherstrip
p/n: 30-0014-52
This windshield gasket weatherstrip comes in a ten foot (10') strip and mounts around the full perimeter of the front glass. It has the slot to accommodate the outer edge's decorative molding and the ends may require trimming and bonding for installation.
Engine Mount Service – Revulcanization Only
p/n: 30-0185-11
This Revulcanization Service Only is designed to restore your Rear Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Hood to Cowl Bumpers
p/n: 30-0223-42
Bumpers, hood to cowl. Brass core, one and one half (1-1/2) inch by four and one half (4-1/2) inch.Length: 4.50 inches. Width: 1.50 inches.
Detachable Center Post Pad
p/n: 30-0286-67
Pads, lower, top removable center pillar, right and left. Brass core.Width: 3.375 inches. Height: 2.75 inches.
Detachable Center Post Pad
p/n: 30-0287-67
Pads, convertible top folding pillar (top main bow hinge), right and left, with brass core.
Side Roof Rail Weatherstrip
p/n: 30-0031-65
Weatherstrip, side window. Fits metal channel. Made of high-quality EPDM rubber. Twelve (12) foot strip.
Windshield Gasket
p/n: 70-2021-50
This Windshield Gasket mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends. It also has the slot to accommodate the outer edge's decorative molding.
Door Check Strap
p/n: 40-0535-70
Strap, door check. T-type, special heavy duty construction of rubber with multiple ply webbing and molded-in steel crossbar. Full length as original with one eighth (1/8) inch by seven eighths (7/8) inch steel crossbar.
Front spring bushing
p/n: 30-0393-32
Bushing assembly, front wheel support; upper and outer. Inlox type cartridge bushing assembly.
Front Suspension Bumper
p/n: 30-0490-32
Bumper, front suspension (inside of coil spring). Made with three five sixteenths (5/16) inch studs as original.
Front Door Vent Window Weatherstrip Set
p/n: 30-0103-55
This four (4) piece Front Door Vent Window Weatherstrip Set contains the upper and lower seals that cover the top, front, and bottom of the vent window. All of the pieces are designed from original parts for a precise, factory fit.
Front Door Vent Window Set
p/n: 90-0327-90
This six (6) piece Front Door Vent Window Set contains the upper and lower seals that cover the top, front, and bottom of the vent window as well as the division post seals.
Suspension Bushing
p/n: 30-0386-36
Bushing and pin assembly cartridge. Inlox type, front wheel lower support arm inner pin. Shipped with instructions for reinstalling.Length: 5.75 inches.
Detachable Center Post Pad
p/n: 30-0261-67
Pad set, detachable center post, folding top upper and lower, right and left. Steel cores as original. 4 piece set.Width: 3.0 inches. Height: 2.75 inches.
Crankshaft Vibration Damper - Revulcanization Only
p/n: 30-0376-12
This Revulcanization Service Only is designed to restore the Crankshaft Vibration Damper to a like new original condition. This revulcanizing service is for the rubber cushion elements. Service requires your metal core.