Running Board Matting
p/n: 30-0218-49
Running board matting for Model 115C only. Made from the molded running board matting for the 120's (our #30-0214-49).
Suspension Bushing
p/n: 30-0386-36
Bushing and pin assembly cartridge. Inlox type, front wheel lower support arm inner pin. Shipped with instructions for reinstalling.Length: 5.75 inches.
Engine Mount Service – Revulcanization Only
p/n: 30-0360-11
This Revulcanization Service Only is designed to restore your Rear Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Front Suspension Bumper
p/n: 30-0228-32
Bumper assembly, front suspension inside coil spring, with five sixteenths (5/16) inch threaded studs as found originally.
Front Door Vent Window Weatherstrips
p/n: 30-0098-55
These Front Door Vent Window Weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts but both strips need to be cut in to three (3) sections to facilitate installation.
Front spring bushing
p/n: 30-0393-32
Bushing assembly, front wheel support; upper and outer. Inlox type cartridge bushing assembly.
Side Roof Rail Weatherstrip
p/n: 30-0031-65
Weatherstrip, side window. Fits metal channel. Made of high-quality EPDM rubber. Twelve (12) foot strip.
Transmission Stabilizer
p/n: 30-0252-24
Stabilizer, fore and aft transmission to frame. A factory service part used to remedy clutch chatter. Steel core as original.Length: 7.50 inches.
Front suspension bushing
p/n: 30-0239-32
Bushings, front suspension torque arm. Necessary for proper front end geometry.
Door Lock Striker Revulcanization Service
p/n: 30-0398-71
This Revulcanization Service Only is to restore your front or rear Door Lock Striker to it's like new original condition. Service requires your old metal striker core. Please call or email for more service details and ordering.
Front spring bumper
p/n: 30-0227-32
Bumper assembly, front spring rebound (upper arm). Steel core, with treaded stud just like original.
Door weatherstrip
p/n: 30-0085-73
Weatherstrip, door, hollow bulb seal construction to replace composite sponge and solid rubber. Retained by metal clips (not included, see our #70-0391-73).
Axle Rebound Pad
p/n: 30-0054-32
Pads, rear axle rebound.Length: 5.125 inches. Width: 1.4375 inches.
Gearshift Boot
p/n: 30-0178-24
Boot, gearshift cover. For cane shifts only. Length: 4.0 inches. Width: 3.0 inches. Height: 5.125 inches.
Front Bumper Grommet
p/n: 30-0077-28
Grommets, front bumper. Molded right and left, including retaining flange. Fully molded rubber.
Accelerator Pedal Service
p/n: 30-0400-41
Revulcanization Service Only for Black Rubber Accelerator Pedal Pad. Includes new ball sockets as original, with correctly detailed tread pattern.
Rear Bumper Grommet
p/n: 30-0047-29
Grommets, rear bumper. For models with luggage racks. Length: 4.125 inches. Width: 3.375 inches.
Engine Mount Pad
p/n: 30-0238-11
This Engine Mount Pad pair is used as a support cushion at the timing gear cover. Correct design and rubber compound. Sold only in pairs. One (1) pair required per car.
Fender Welting 1/4" Bead - 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body.
Chrome Fender Welting - 50ft
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Fender Welting with 3/16" Bead - 50ft
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Dashboard Anti-Rattle
p/n: 30-0025-20
Anti rattle, each end of instrument panel. Beaded edge as original, eight and one half (8-1/2) inch long. Replaces 310708 & 310709.
Red Brake and Clutch Pedal Pad
p/n: 30-0188-89
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0188-22.Length: 3.875 inches. Width: 2.875 inches.
Taillight Mounting Pad
p/n: 30-0230-15
Gaskets, taillight mounting. Proper type lip as original. One and eleven sixteenths (1-11/16) inch by four and one half (4-1/4) inch.Length: 4.25 inches.
Brake and Clutch Pedal Pads
p/n: 30-0188-22
Pads, brake and clutch pedal, slip over type. Black rubber only. For black and red (semi-automatic clutch models) see our #30-0188-89.Length: 3.875 inches.
Radiator Mounting Pad
p/n: 30-0309-31
Grommet, several usages. Radiator core cradle tie rod to frame or rear stabilizer pad to link to where the leaf springs are bolted. Fully molded rubber. 2nd type with chamfered edge. Comes as a (4) piece set.
Radiator Mounting Pad
p/n: 30-0208-31
Pad, radiator lower splasher to grille. Fastens into place with rivets. One four (4) piece set required per car.Length: .875 inches. Width: .875 inches.
Cowl Vent Gasket
p/n: 30-0179-54
Gasket, cowl vent, original labyrinth type, not sponge.Length: 14.75 inches. Width: 5.50 inches.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Rumble Seat Step Mounting Pad
p/n: 30-0271-44
Gasket, rumble seat step center. Length: 5.875 inches.
Brake and Clutch Shank Seal
p/n: 30-0143-24
Boot, brake and clutch pedal shank at toe board.Length: 2.9375 inches.
Fender Welting 1/4" Bead - 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty-five (25) foot roll. Typically used to attach two (2) fenders to body.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Rumble Seat Step Mounting Pad
p/n: 30-0272-44
Gasket, rumble seat step. For left hand drive upper. Length: 5.0 inches.
Rumble Seat Lid Bumper Pad
p/n: 30-0275-44
Bumpers, rumble seat stop bracket. Self-retaining type as original.Length: 1.1875 inches. Width: .75 inches. Height: .375 inches.
Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Shock Absorber Bushing
p/n: 30-0024-33
Bushings, rear shock link assembly. Designed to act like sleeve inside link arm.Height: .9375 inches.
5" Wide Bow Drill Cloth Tape
p/n: 70-1175-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Taillight Lens Gasket
p/n: 30-0336-15
Gaskets, taillight door lens. For cars without center license light. Two (2) strips eleven and one half (11-1/2) inches long each.Length: 11.5 inches.
Shock Absorber Link Bushings
p/n: 30-0226-33
A Rear Shock Absorber Upper Link Bushing pair designed from the original part for superior fitment and function. Rubber sleeve construction like original.