Crankshaft Vibration Damper - Revulcanization Only
p/n: 30-0376-12
This Revulcanization Service Only is designed to restore the Crankshaft Vibration Damper to a like new original condition. This revulcanizing service is for the rubber cushion elements. Service requires your metal core.
Front Door Vent Window Weatherstrips
p/n: 30-0089-55
These Front Door Vent Window Weatherstrips are designed from the original parts for superior fitment and seal. The pieces are molded as left and right and are one piece with the division post seal.
Suspension Bushing
p/n: 30-0386-36
Bushing and pin assembly cartridge. Inlox type, front wheel lower support arm inner pin. Shipped with instructions for reinstalling.Length: 5.75 inches.
Front Suspension Bumper
p/n: 30-0490-32
Bumper, front suspension (inside of coil spring). Made with three five sixteenths (5/16) inch studs as original.
Front spring bushing
p/n: 30-0393-32
Bushing assembly, front wheel support; upper and outer. Inlox type cartridge bushing assembly.
Door Check Strap
p/n: 40-0535-70
Strap, door check. T-type, special heavy duty construction of rubber with multiple ply webbing and molded-in steel crossbar. Full length as original with one eighth (1/8) inch by seven eighths (7/8) inch steel crossbar.
Windshield Gasket
p/n: 30-0477-50
This Windshield Gasket mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket
p/n: 30-0479-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Hood to Cowl Weatherstrip
p/n: 30-0138-42
Guard strip, hood to cowl. Brass core with molded integral hood rest.Length: 14.875 inches.
Engine Mount Service – Revulcanization Only
p/n: 30-0185-11
This Revulcanization Service Only is designed to restore your Rear Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Windshield Gasket Weatherstrip
p/n: 30-0014-52
This windshield gasket weatherstrip comes in a ten foot (10') strip and mounts around the full perimeter of the front glass. It has the slot to accommodate the outer edge's decorative molding and the ends may require trimming and bonding for installation.
Hood Corner Pad
p/n: 30-0130-42
Pads, hood front corners. Large self prong type with metal core molded left and right.Length: 3.375 inches.
Front suspension bushing
p/n: 30-0239-32
Bushings, front suspension torque arm. Necessary for proper front end geometry.
Headlight Mounting Pad
p/n: 30-0134-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. Made with a metal core. This pad acts as the headlight adjusting collar.
Engine Mount Service – Revulcanization Only
p/n: 30-0543-11
This Revulcanization Service Only is designed to restore your Engine Mount Stabilizer Bracket to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Axle Rebound Pad
p/n: 30-0054-32
Pads, rear axle rebound.Length: 5.125 inches. Width: 1.4375 inches.
Front Fender Seal
p/n: 30-0189-44
Liners, front fender to running board. Reversible right and left like original. Length: 15.0 inches.
Rear Bumper Grommet
p/n: 30-0006-29
Grommets, rear bumper.Length: 3.625 inches. Width: 3.3125 inches.
Running Board Edge Seal
p/n: 30-0169-44
Liner, running board to body, (side apron to body seal). Set consists of two (2) pieces seven (7) foot long. One (1) inch width is after fold over.
Front Bumper Grommet
p/n: 30-0171-28
Grommets, front bumper. Molded right and left with correct detail as originally found. Fully molded rubber.
Rigid Run Channel
p/n: 30-0180-57
Channel, rigid run, for vent window division bar. Chrome beaded edge, mohair lined steel channel to proper dimensions for window side of wing window frame.
Stabilizer Bushing
p/n: 30-0484-33
Bearings, stabilizer front rod. Requires two (2) per car. Fully molded rubber.
Gearshift Seal
p/n: 30-0165-24
Seal, gearshift to floorboard.Length: 5.625 inches. Width: 4.875 inches.