Front Door Vent Window Set
p/n: 90-0436-90
This front door vent window weatherstrip set is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Engine Mount Service – Revulcanization Only
p/n: 70-0548-11
This Revulcanization Service Only is designed to restore your Front Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Front Door Vent Window Weatherstrips
p/n: 38-0103-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Windshield Gasket
p/n: 70-1005-50
This windshield gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit.
Prop shaft support service
p/n: 70-0748-27
Bearing support bracket assembly, drive shaft center bearing. Revulcanization service only. .
Engine Mount Service – Revulcanization Only
p/n: 70-0629-11
This Revulcanization Service Only is designed to restore your Rear Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Cadillac Master Parts List 1957 - 1964 (Reprint)
p/n: 07-1443-07
This 1957-1964 Cadillac Master Parts List - Two (2) Volume set licensed Detroit Iron reprint provides the most comprehensive repair information in paper format. This OEM PARTS manual reproduction provides detailed original part numbers, part assembly diagrams / illustrations and part textual details for all vehicle subsystems.
Cowl Drain Gutter
p/n: 70-0867-73
Gutter, cowl side drain, left and right. Rubber with metal core as original. Eleven (11") inches long.Length: 11.0 inches.
Splash Apron / A-Arm Dust Shield Filler Set
p/n: 70-2495-45
This fourteen (14) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Defroster Vent Gasket
p/n: 70-2279-31
Gasket, defroster vent at base of windshield. One (1) pair required per car.
Fender Skirt Edge Weatherstrip
p/n: 70-0154-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Hood To Cowl Weatherstrip
p/n: 70-1019-42
This Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This weatherstrip mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.
Axle Rebound Pad
p/n: 70-2225-32
Bumper, rear spring axle impact. Located on frame rail. Rubber only, does not include metal retaining clips or bolts.
Beltline Weatherstrips
p/n: 70-1121-61
These Beltline Weatherstrips (sometimes called "scraper seal") come in a three (3) foot pair. For use on front, rear, and quarter windows without a chrome reveal molding at the window beltline. Available in 3ft pair.
Front coil spring pad
p/n: 70-2302-35
Pad, front coil spring insulator cushion. Fully molded, mounts at top of front coil springs.
Front Door Hinge Pillar Weatherstrips
p/n: 60-0326-73
This Front Door Hinge Pillar Weatherstrip set fits at the front door opening. Auxiliary on door hinge pillar at beltline, right and left. Sometimes called "L" or "J" strips. Fully molded with authentic configuration to help guide water to the outside of vehicle.
1935-1974 Cadillac Factory Parts Manual, CD
p/n: 07-1346-07
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Cadillac Factory parts manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
Beltline Weatherstrip
p/n: 70-1120-61
This Beltline Weatherstrip comes in a six (6) foot length for the outer beltline (sometimes called "scraper seal"). For use on front, rear, and quarter windows without a chrome reveal molding at the window beltline. Available in 6ft lengths.
Beltline Weatherstrip Channel
p/n: 70-0651-58
This Beltline Weatherstrip Channel is a five (5) foot length of rigid channel with a flocked rubber lip and a flat stainless bead. Can be used as the inner beltline weatherstrip on front doors, rear doors and quarter windows.
Vent division bar weatherstrip
p/n: 70-1014-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0773-WT
This Peel-N-Stick Trunk Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk directly to the body.
Suspension arm bumper
p/n: 70-1021-32
Bumper, front or rear suspension, upper. Uses two (2) per car on front suspension, one (1) per car on rear.
Wiper Transmission Gasket
p/n: 60-0593-53
Wiper Transmission Gasket - This is the seal for the wiper motor crank. For two (2) speed wiper motors only. These parts are made of the highest quality and authenticity. Replaces # 4906021.
Trunk Weatherstrip
p/n: 70-0773-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Front Stabilizer Bar End Link Set
p/n: 70-2110-33
A twenty-two (22) piece Front Stabilizer Bar End Link set. Comes complete with fasteners, metal sleeves, metal cup washers and black rubber bushings. One (1) end link set for both sides of stabilizer bar on one (1) car.
Radiator Upper Support Filler
p/n: 70-2502-45
This single piece Radiator Upper Support Filler is designed from the original part for superior fitment and function. Filler piece is die cut from quality masticated rubber to authentic original dimensions. Fits at radiator to radiator upper support.
Radiator Mounting Pad
p/n: 70-0963-31
Radiator mounting pad, insulator. Up to four (4) used per car.Length: 6.0 inches.
Metal Sleeved Grommet
p/n: 70-0203-41
Flanged rubber grommet with metal sleeve bushing. Used as part of the accelerator relay lever. Also used from 1959-61 on all Cadillac models as a bushing for the windshield wiper relay lever adaptor.
Body Mount Isolator Pad
p/n: 70-0929-48
Body Mount Isolator Pad - Rubber with metal core and locating collar as original part. Part dimensions = Two and three sixteenths inch (2 3/16") square by one inch (1") overall height with thirteen sixteenths inch (13/16") inside bolt diameter. Does not include any fastener hardware.
Door Handle Gasket Set
p/n: 70-0925-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Taillight Lens Gaskets
p/n: 70-3235-15
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between taillight lens & taillight housing.
Directional and Parking Light Lens Gaskets
p/n: 70-3115-16
This Turn Signal and Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Signal / Parking Light Lens and the Signal / Parking Light Housing or Bezel.
Hood Bumper
p/n: 70-0770-42
Bumper, fender to hood. Correct detail with ridges as original. Four (4) required per car.Length: 1.3125 inches.
Taillight Lens Gaskets - In Fin
p/n: 70-3502-15
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. These reproduction gaskets fit between the taillight lens & taillight housing in fin.
Back Up Light Lens Gaskets
p/n: 70-3234-17
This Back Up Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the back-up light lens and the back-up light housing or light bezel.
Beltline Guide Plate - Plastic
p/n: 50-0384-62
This Beltline Guide Plate is designed from the original part for superior fitment and function. High quality plastic plate attaches to various outer beltline window scraper weatherstrips.
Hood Bumper
p/n: 70-0907-42
Bumper, hood front aligning. Correct design with proper screw thread.Height: 2.50 inches.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Headlight Bucket to Fender Seals
p/n: 70-3085-14
This two (2) piece Headlight Bucket to Fender Seal pair is designed from the original part for superior fitment and seal. Die cut from original style masticated rubber for a like factory fit.
Body Mount Isolator
p/n: 70-2232-48
Isolator, body mounting to chassis. Fully molded rubber. One and seven eighths inch (1 7/8") outside diameter by fifteen sixteenths inch (15/16") inside hole diameter by nine sixteenths inch (9/16") height.
Body Mounting Pad
p/n: 70-2233-48
Pad, body mounting to chassis. Fully molded rubber. One and seven eighths inch (1 7/8") outside diameter by eleven sixteenths inch (11/16") inside hole diameter by nine sixteenths inch (9/16") height.
Body Mounting Pad
p/n: 70-2234-48
Pad, body mounting to chassis. Fully molded rubber, square type. Six (6) or more are used per car. Two and three sixteenths inch (2 3/16") square by three fourths inch (3/4") inside diameter hole by one half inch (1/2") inch height.
Plastic Guide Plate
p/n: 50-0385-58
Plastic guide plate, attaches to various outer scraper weatherstrips.Length: 1.625 inches. Width: .625 inches.
Rear View Mirror Mounting Pad
p/n: 70-3083-70
This single Rear View Mirror Mounting Pad To Door gasket is designed from the original part for superior fitment and seal. The gasket is precision die cut to the original specifications. This gasket is for one (1) door mounted rear view mirror.
Headlight dimmer switch pad
p/n: 70-0930-14
Pad, headlight dimmer switch. Rubber slip-over cover for floor mounted switch.
Spark Plug Wire Spacer
p/n: 70-0394-21
This Spark Plug Wire Spacer is designed from the original part for superior fitment and function. This spacer fits spark plug wires into the organizer bracket.
Multi-Purpose Clips
p/n: 70-4802-45
A ten (10) piece set of Multi-Purpose Clips. Commonly used to retain Hood to Cowl Weatherstrips or Inner Fender Splash Panels.