Hood to Fender Bumper
p/n: 30-0304-42
This Hood to Fender Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure. Six (6) required per car.
Accelerator Hinge Grommet
p/n: 30-0539-41
Grommet, accelerator pedal hinge to floorboard. Length: 3.50 inches. Width: 2.50 inches.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Body Mounting Pad
p/n: 70-1429-48
Pad, body mounting. Fully molded rubber with metal core and rubber locating collar. Also used for radiator cradle to frame. Eight (8) to ten (10) required per car. Two and one fourth inch (2 1/4") outside diameter by one and one sixteenth inch (1 1/16") l
Body Mounting Pad
p/n: 30-0500-48
Pad, body mounting. Fully molded rubber with locating collar and metal core. Number used varied according to body type.
Power brake carpet grommet
p/n: 70-3147-24
Grommet, carpet. Floor front carpet grommet use for power brake hole.
Firewall Seal
p/n: 70-1600-36
Grommet, power steering lines to frame.Length: 2.75 inches. Height: .75 inches.
Body Mounting Pad
p/n: 30-0501-48
Pad, body mounting. Fully molded rubber with metal core. Number used varied according to body type.
Power window switch bezel pad
p/n: 70-2136-21
Mounting pad, power window die cast bezel. Used under single window switch, typically found on front passenger door and rear windows.
Firewall Seal
p/n: 70-1599-36
Grommet, power steering lines to air duct.Length: 3.3125 inches. Width: .75 inches.
Power Window Switch Bezel Pad
p/n: 70-2137-21
Mounting pad, power window die cast bezel. Used under 4 way switch, typically found on drivers door.Width: 2.0 inches.
2" Firewall Grommet
p/n: 70-1725-20
This Firewall Grommet is used to run the windshield washer hose and antenna wiring through the firewall. Designed from the original part for superior fit and seal.
2" Wiring Harness Firewall Grommet
p/n: 70-1724-20
This Wiring Harness Firewall Grommet is used to run the main wiring harness through the firewall. Designed from the original part for superior fit and seal.
Firewall Grommet
p/n: 30-0456-20
This Firewall Grommet is used for the heater core at the firewall. Designed from the original part for superior fit and seal.
Hood to Cowl Weatherstrip
p/n: 30-0527-42
Weatherstrip, hood to cowl. Overall thirty seven (37) inches long.
Windshield weatherstrip
p/n: 70-1535-52
Weatherstrip, windshield garnish molding on lower windshield post. Molded rubber replacement for #469222-3.
Front Stabilizer Bushing
p/n: 30-0298-33
Bushings, front stabilizer rod end. One (1) pair required per car. Fully molded rubber.
Coil Wire Sleeve
p/n: 70-2052-21
Boot, spark plug wire, at spark plug. All original textures and details.Length: 2.0 inches.
Beltline Weatherstrip
p/n: 30-0300-58
Window felt inner and/or outer. Flexible, pile lined, rubber covered, with stainless bead. Available in 3ft pair.
Vent Window Division Bar Weatherstrip
p/n: 30-0541-74
Division post seal pair for rear door vent window. Made from top quality rubber to ensure durability and proper seal. Designed from original part so it fits correctly.
Rear Shield to Bumper Seal
p/n: 30-0476-44
This Rear Shield to Bumper Seal is made of high quality EPDM dense rubber. The seal is designed from an original part so it fits correctly. Overall length is seven (7) feet.