Running Board Matting
p/n: 40-0212-49
This Running Board Matting is designed from the original part for superior fitment and a factory like appearance. This four (4) piece set consists of one (1) pair of our #40-0151-49 mats plus two (2) extension pieces to give correct fit for the longer Model CT model running boards.
Accelerator Pedal Pad
p/n: 40-0014-40
Accelerator pedal. Perfect copy in every detail, including heavy two (2) piece metal core with mounting tabs as original.Length: 10.3125 inches.
Door Check Strap
p/n: 40-0535-70
Strap, door check. T-type, special heavy duty construction of rubber with multiple ply webbing and molded-in steel crossbar. Full length as original with one eighth (1/8) inch by seven eighths (7/8) inch steel crossbar.
Axle Rebound Pad
p/n: 40-0373-32
Bumpers, rear axle. Revulcanization service only.Length: 3.0 inches.
Rear Bumper Grommet
p/n: 40-0112-30
Grommets, rear bumper symmetrical, right and left. Perfect detailing on both inner and outer surfaces. Fully molded rubber.
Swing-Out Windshield Weatherstrip
p/n: 70-0057-52
This Swing-Out Windshield Weatherstrip is designed from the original part for superior fitment, finish and sealing function. This windshield weatherstrip is common for most Chrysler models. May also be found in DeSoto, Dodge and Plymouth models. Also used in Packard and Studebaker models.
Rumble Seat Step Pad
p/n: 40-0012-44
Pad, rumble seat step bears Chrysler medallion logo in center.Height: .50 inches.
Chrome Fender Welting - 50ft
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Fender Welting 1/4" Bead - 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body.
Fender Welting with 3/16" Bead - 50ft
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Brake and Clutch Pedal Pads
p/n: 40-0038-22
Pad, brake and clutch pedal. See also our #40-0072-22.Length: 3.8125 inches. Width: 2.3125 inches.
Rear Bumper Grommet
p/n: 40-0180-30
Grommet, rear bumper support bar to gas tank apron. One and three fourths (1-3/4) inch inside diameter.
Carpet Heel Plate
p/n: 40-0087-88
Heel pad for carpet. Identical to original. Five and three fourths (5-3/4) inch by ten and one half (10-1/2) inch, to be stitched in place.Length: 10.
Hood Corner Pad
p/n: 40-0127-42
Pads, hood corners, brass core. Approximately 80 degree angle. Integral tabs for installing.Length: 1.50 inches.
Hood Corner Pad
p/n: 40-0128-42
Pads, hood corners. Square type, brass core. Integral installation tabs. 90 degree angle, used on front or rear corners, as required.
Rear Window Gasket
p/n: 70-0084-77
This Rear Window Gasket comes in a seven foot, six inch (7' 6") strip and mounts around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Windshield Gasket
p/n: 40-0320-52
This Windshield Gasket comes in a four (4) foot strip and is for the lower glass frame to cowl. This weatherstrip is for 2 piece windshields.
Fuel Neck Grommet
p/n: 40-0091-39
Grommet, fuel filler neck. Fully molded large oval style. Bottom is flat. Four and one half inch (4-1/2") outside width by five by one half inch (5-1/2") outside length. Two and five sixteenths inch (2-5/16") inside hole diameter.
Door - Gravel Shield - Running Board Weatherstrip
p/n: 60-0054-73
This Door - Gravel Shield - Running Board Weatherstrip is a anti-squeak bulb type extrusion with fitment for General Motors vehicles. A twelve (12) foot strip made of high-quality EPDM dense rubber and designed from original parts for superior fitment, finish and function.
Cowl Vent Gaskets
p/n: 40-0170-54
This Cowl Vent Gasket is manufactured from high quality EPDM sponge rubber. For twin cowl vents of thirty four (34") inch circumference.
Hood Bumper
p/n: 40-0164-42
Pad, hood panel center bracket. Hollow, to fit over original steel bracket.Length: 1.375 inches. Width: 1.375 inches.
Side Mount Cover Pad
p/n: 40-0314-37
Anti-rattle, spare wheel cover in fenderwell.Width: .25 inches.
Vacuum Clutch Cylinder Boot
p/n: 40-0084-24
Boot, automatic clutch vacuum cylinder rod.Length: 4.0 inches.
Fuel Neck Grommet
p/n: 40-0067-39
Grommet, fuel filler neck. Oblong, fully molded rubber. Four and one eighth inch (4-1/8") outside length by two and one fourth inch (2-1/4") inside diameter.
Hood Bumper
p/n: 40-0354-42
Bumper, fender to hood. Two (2) per car. Held by four (4) rivets.Length: 2.9375 inches.
Door Weatherstrip
p/n: 40-0208-73
Weatherstrip, door bottom on door. Three thirty seconds (3/32) inch thick, two (2) inch wide, perforated for retaining screws. Forty eight (48) inch strip.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Fender Welting 1/4" Bead - 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty-five (25) foot roll. Typically used to attach two (2) fenders to body.
Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Brake and Clutch Shank Seal
p/n: 40-0175-24
Seal, brake and clutch pedal shank to floorboard. One and one half (1-1/2) inch by two and one eighth (2-1/8) inch by three fourths (3/4) inch thick.
Horn trumpet grommet
p/n: 40-0086-21
Grommet for trumpet horn wire through motor cover. Close reproduction. Two (2) per car.
Flexible Run Channel - 30 Inch Pair
p/n: 40-0309-57
Channel, side window glass, vertical run. Flexible, felt lined, rubber covered channel. Available in 30" pair.
Brake and Clutch Shank Seal
p/n: 50-0066-24
Grommet, brake and clutch pedal floor seal.Width: 1.8125 inches. Height: 2.375 inches.
Brake and Clutch Shank Seal
p/n: 40-0016-24
Seal, brake and clutch pedal shank to floorboard (draft excluder).Length: 2.4375 inches. Width: 1.875 inches.
Rumble Seat Lid Bumper Pad
p/n: 40-0297-85
Bumper, rumble seat lid. Sometimes used on trunk. One half (1/2) inch by one (1) inch by one (1) inch. Two (2) per car.Length: 1.0 inches. Width: 1.0 inches.
Taillight Mounting Pad
p/n: 40-0061-15
Pad, taillight mounting. Chrysler 1932-33 Pad, taillight mounting. Chrysler and other WPC cars. Chrysler 1932-33 Pad, rumble seat step mounting.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Door Bumper
p/n: 40-0316-70
Bumper, door side, lower, on lock post. Retained by dovetail tapping plate.Length: 1.5625 inches. Width: 1.5625 inches.
Coil wire sleeve
p/n: 40-0336-21
Nipple, sparkplug wire at sparkplug, for right angle plug terminal. This is an exact copy of the style used at the time. Not a modernistic makeover.
Door Bumper
p/n: 40-0037-70
Pad, door jamb. One and nine sixteenths (1-9/16) inch long by one and one eighth (1-1/8) inch wide.Length: 1.625 inches. Width: 1.0625 inches.
Shock or Stabilizer Link Cross Pin Bushing
p/n: 50-0220-32
This Shock or Stabilizer Link Cross Pin Bushing is designed from the original part for superior fitment and function. A rubber bushing for shock absorber link cross pin or stabilizer cross link pin.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Door and Trunk Handle Gasket
p/n: 40-0132-70
Pad, door handle escutcheon. Two and five sixteenths (2-5/16) inch by one and seven sixteenths (1-7/16) inch.
Door Bumper
p/n: 40-0010-70
Pad, door jamb, fully detailed. One and one eighth (1-1/8) inch long, one and one fourth (1-1/4) inch wide.Length: 1.125 inches. Width: 1.25 inches.
Battery Cable Grommet
p/n: 40-0333-21
Grommet, battery hot cable through frame. Three fourths (3/4) inch inside diameter for one and three sixteenths (1-3/16) inch hole through frame.
Door Bumper
p/n: 70-1156-71
Door Side Bumper made from EPDM Dense rubber. Clip retained. Appears identical to Atwood #107, #208. Width: 1-1/2" inches. Height: 1-5/16"
Door Bumper
p/n: 40-0154-70
Bumper, door side. One and one fourth (1-1/4) inch long by one (1) inch wide. Similar to our #40-0010-70, but different workface.Length: 1.0 inches.
1/8" x 7/8" Fabric Hood Lacing
p/n: 60-0578-42
This 1/8" x 7/8" Fabric Hood Lacing is high quality original style woven cotton hood to cowl lacing. This lacing has the slot to install a wire insert or fasten with rivets if so found originally. Available by the foot to accommodate any job.
3/16" x 3/4" Fabric Hood Lacing
p/n: 70-2221-42
This 3/16" x 3/4" Fabric Hood Lacing is made of a high-quality original style woven cotton. Available by the foot to accommodate any job.
Front and Rear Door Bumper
p/n: 34-0025-42
High quality steel core Front and Rear Door Bumper for front and rear body hinge pillar. Mounted by screw. For auxiliary use only where needed to prevent door rattles. Replaces factory #372341.
Rear Spring Thrust Washer
p/n: 40-0526-32
Thrust washer, rear spring. "Silent Block". Three sixteenths (3/16) inch thick. Seven eighths (7/8) inch by one and five eighths (1-5/8).
Rear Spring Thrust Washer
p/n: 40-0525-32
Thrust washer, rear spring. "Silent Block". Three sixteenths (3/16) inch thick. One (1) inch by one and three fourths (1-3/4) inch.
11/16" Channel Filler Weatherstrip
p/n: 70-0241-57
Weatherstrip, side window, double-lip seal type, used as filler for one fourth (1/4) inch glass in metal carrier channel. Available by the foot.
9/16" Side Window Upper Weatherstrip
p/n: 40-0280-57
This Side Window Upper Weatherstrip is made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
1/16" Sash Channel Filler - Cork
p/n: 70-1115-57
This 1/16" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
1/2" Trunk Weatherstrip
p/n: 70-0231-85
This 1/2" Trunk Weatherstrip is designed from the original part for superior fitment, finish and function. Available by the foot to satisfy your specific length requirement
1/16" Sash Channel Filler - Rubber
p/n: 70-2170-57
This 1/16" Sash Channel Filler offers the best quality rubber product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
1/32" Sash Channel Filler - Cork
p/n: 70-1114-57
This 1/32" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
1/32" Sash Channel Filler - Rubber
p/n: 70-2169-57
This 1/32" Sash Channel Filler offers the best quality rubber product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
1/4" Universal Mounting Pad
p/n: 70-0308-17
This Universal Mounting Pad is used for lights, hinges, brackets, and other bright work when no molded pad is available. Manufactured with a special edge lip to hug bright work when clamped down. Shape outline to suit application.
3/4" Side Window Weatherstrip
p/n: 70-0064-57
Seal, lower side window. Fastens to inner face of door to seal against outer side of glass. Available by the foot.
3/4" Wiper Control Grommet
p/n: 32-0317-52
This Wiper Control Grommet is fully molded and designed from the original part for superior fitment and seal. Designed to run the windshield wiper shaft through the body.
