Center Division Bar Chrome Molding Retainer
p/n: 70-0373-51
Center Division Bar Chrome Molding Retainer for outside windshield center post stainless molding. Use with original stainless molding and clips. Length: 15-1/2 inches. Width: 1-1/4 inches.
License Light Mounting Pad
p/n: 50-0034-17
Pad, rear license light and trunk handle body.Length: 7.50 inches.
Brake and Clutch Shank Seal
p/n: 50-0066-24
Grommet, brake and clutch pedal floor seal.Width: 1.8125 inches. Height: 2.375 inches.
Clutch and Brake Pedal Pads - Black
p/n: 50-0054-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Front coil spring pad
p/n: 50-0358-35
Insulators, front coil spring. Fabric reinforced rubber as original.
2-1/4" Firewall Grommet
p/n: 50-0166-20
This Firewall Grommet is used to run the wiring harness through the firewall mat. Designed from the original part for superior fit and seal.
Door Check Link Rod End Stop
p/n: 70-0479-70
End nut, check link (rubber bar with steel bar insert). Three fourths (3/4) inch by three fourths (3/4) inch by two (2) inch threaded five sixteenths (5/16) inch. (For round stop nut, see our #70-0326-70).
Headlight Mounting Pad
p/n: 50-0462-14
Headlight housing to fender gasket. Steel rule die-cut replacement for #1320452.
Body Mounting Pad
p/n: 50-0477-48
Pad, body mounting. Fully molded rubber with metal core & locating collar.
1-3/8" Firewall Grommet
p/n: 50-0327-20
This Firewall Grommet is used to run the speedometer cable through the lower firewall. Designed from original parts for excellent workmanship.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Window Stop Stem Bumpers
p/n: 33-0675-62
This Window Stop Stem Bumper pair is designed from the original part for an authentic fit, finish, and appearance. Cushion window stop pair for the lower front and or rear doors rear side and quarter windows as needed.
Body Mounting Pad
p/n: 50-0096-48
Pad, body mounting. Fully molded rubber with steel core and locating collar.
Rear coil spring pad
p/n: 50-0304-35
Insulator, rear coil spring clamp bolt (upper end). Two (2) per car. Fabric reinforced rubber as original.
Front Bumper Gravel Shield
p/n: 70-0127-30
This anti-rattle Front Bumper Gravel Shield pad is designed from the original part for superior fitment and seal. Fully molded with top quality EPDM rubber over a corrosion resistant brass core to ensure durability, fit and appearance.
Ferrule and Grommet Set
p/n: 70-0597-69
This Ferrule and Grommet Set for the outside door handle is cadmium plated ferrule with rubber sleeve. Two (2) piece set for one (1) door.
Body Mounting Pad
p/n: 50-0329-48
Pad, body mounting. Under frame bracket for hold-down nut. Fully molded rubber. Check number needed for your particular body.
1-3/8" Firewall Grommet
p/n: 50-0531-20
This Firewall Grommet is used to run the oil pressure, water temperature, and vacuum line through the firewall. Designed from original part for excellent workmanship.
Hood Bumper
p/n: 34-0311-42
Bumper, hood, fastened to cowl at rear of hood. Steel core. One and eleven sixteenths (1-11/16) inch diameter. Two (2) per car.
Vent Window Division Post Weatherstrip
p/n: 70-0040-56
This Vent Window Division Post Weatherstrip is an extruded thirty (30") inch rubber strip that may have to be glued to your old original division post seal core, or directly to the division post.
Clutch and Brake Pedal Bump Stops
p/n: 70-4805-24
This Clutch and Brake Pedal Bump Stop pair is designed from the original part for superior fitment, finish and function. These rubber bumpers help align your brake and clutch pedals in the correct position, while also preventing rattles and squeaks.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Body Mounting Pad
p/n: 50-0097-48
Pad, several usages. Use as a body mounting pad or as a cushion for body mounting bolt. Fully molded rubber. Up to twenty (20) required per car.
Body Mounting Pad
p/n: 50-0328-48
Pad, body mounting to frame. Fully molded rubber. Up to twenty (20) required per car. Check number needed for your particular body. Two inch (2") square by five eights inch (5/8") inside hole diameter by seven sixteenths inch (7/16") height.
Axle Rebound Pad
p/n: 50-0302-35
Bushing, rear axle, anti-sway rod ends. Fully molded rubber. Four (4) required per car.
Door Lock Mounting Pad
p/n: 27-0020-69
Mounting pad, door lock cylinder, right and left.Length: 1.6875 inches.
License Light Socket Grommet
p/n: 50-0395-17
Grommet, license light socket.May fit earlier years.Height: .5 inches.
Window Stop Stem Bumper
p/n: 33-0540-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and function. Designed as a window stop cushion for front and rear door, rear side and quarter windows as needed.
Front and Rear Door Bumper
p/n: 34-0025-42
High quality steel core Front and Rear Door Bumper for front and rear body hinge pillar. Mounted by screw. For auxiliary use only where needed to prevent door rattles. Replaces factory #372341.
Hood Bumper
p/n: 50-0325-42
Bumper, hood front. Slides over metal bracket.1941 model requires two (2) per car. 1942 model requires two to four (2-4) per car.Length: 1.0 inches.
15/16" Trunk Weatherstrip
p/n: 70-0490-85
This Trunk Weatherstrip is made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Trunk Bumper
p/n: 34-0399-87
Bumper, trunk opening on lid. Metal core, as original, screw held. Two (2) required per car.
Door Bumper
p/n: 34-0131-37
Bumper, front door above the upper hinge on the upper radius of the door. Stiff-backed, retained by screw, mounted on door only.
Side Window Roller
p/n: 70-0117-62
This Side Window Roller, anti-rattle roller, is manufactured using EPDM dense rubber to replace the original perfectly. The roller fits both styles of brackets.
Shift Lever Grommet
p/n: 50-0284-24
Grommet, shift lever insulator. One (1) per car. Three eighths (3/8) inch inside diameter by five eighths (5/8) inch barrel by one half (1/2) inch long.
Spark plug grommet
p/n: 70-1181-21
Grommet, spark plug and coil wire at distributor cap outlets. For seven (7mm) millimeter, later years.
Brown Door Lock Knob
p/n: 70-0660-70
This is the Knob or push button for the inside door lock. The part fits over 1/8" steel rod to door lock. Neutral brown color that may be lacquered with other colors as required. A hard rubber part fits many different vehicles.
15/16" Trunk Weatherstrip
p/n: 70-0412-85
This Trunk Weatherstrip is made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Starter Solenoid Cable Rubber Boot
p/n: 70-0704-21
This Starter Solenoid Cable Rubber Boot is designed from the original part for superior fitment and function. This boot covers and protects the battery cable at the starter solenoid connection.
Spark plug grommet
p/n: 70-1180-21
Grommet, spark plug & coil wire at distributor cap outlets. For nine (9mm) millimeter wire, earlier years.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
13/16" Trunk Weatherstrip
p/n: 50-0161-85
This Trunk Weatherstrip was designed from an original part for a specific application but has many uses outside of its original purpose. Available by the foot.
1-5/16" Firewall Grommet
p/n: 50-0532-20
This Firewall Grommet is used to run the parking brake cable through the firewall. Designed from original part for excellent workmanship.
Door Weatherstrip
p/n: 40-0168-73
This Door Weatherstrip is generally used as a hinge post on door or body opening, in area around hinges where irregular cross section is required. Available by the foot.
Steering Knuckle Support Seal
p/n: 50-0199-35
This Steering Knuckle Support Seal is designed from the original part for an authentic fit, finish, and appearance. Fits at the steering knuckle support at the upper pivot pin. Four (4) required per car.
Shock and Stabilizer Grommet
p/n: 70-0274-33
This Shock and Stabilizer Grommet is fully molded using EPDM dense rubber. Designed from original with locating collar. Eight (8) required per car.