Running Board Matting
p/n: 70-0420-49
Running board matting. Fully molded rubber strips with full length steel cores molded in.
Engine Mount Cushions
p/n: 70-0300-11
These Engine Mount Cushions are used as an intermediate engine mount for support bolts. Split in half if needed at installation. A four (4) piece set.
Rear Engine Support Pad
p/n: 70-0443-11
This Rear Engine Support Pad is used as a cushion at transmission. Makes a four (4) piece set after splitting.
Distributor boot
p/n: 70-0004-21
Boot, distributor dust and moisture. Original equipment, exact copy. V-16 only.
Hood Hinge Top Strap Pivot
p/n: 70-0045-42
A Hood Hinge Top Strap Pivot manufactured to OEM specifications to install for an authentic fit and finish. Cold rolled steel as original.
Windshield Weatherstrip Seal Set
p/n: 70-0015-52
This Windshield Weatherstrip Seal Set includes two (2) 15" Single-Flap side weatherstrip seals and one (1) 45" Double-Flat bottom weatherstrip seal. The set seals the windshield glass to the body and protects the interior of vehicle.
Hinge Pillar Weatherstrip
p/n: 70-0734-63
Convertible Hinge Pillar Weatherstrip - Attaches to the body and seals between the A-pillar post and the front section of the door or vent window frame when the door is closed.
Ferrule Installing Tool
p/n: 70-0662-69
Installing tool, door and trunk handle ferrule. For cars and trucks using door and trunk handle ferrules such as our #70-0111-69.
Convertible Top Rest Block
p/n: 70-0069-67
Pads, convertible top rest for rear deck. Two heights as original for inner and outer positions. Four (4) piece set.
Vacuum Clutch / Brake Cylinder Diaphragm
p/n: 50-0063-24
This Electromatic Clutch Control or Brake Vacuum Cylinder Diaphragm is designed from the original part for superior fitment and function. Used in different locations dependent upon vehicle make.
Rigid Run Channel
p/n: 70-0130-58
Special channel, felt lined rubber, for door upper front post for convertibles with cast upper post. Each piece sixteen (16) inches long.
Shock and stabilizer seal
p/n: 70-1185-33
Seals, shock absorber and rear stabilizer link. Eight (8) piece set.
Windshield Weatherstrip Set
p/n: 70-0016-52
This three (3) piece Windshield Weatherstrip Set includes two 16-1/2" side weatherstrip channels and one 48" bottom weatherstrip channel. All corners are correctly molded to fit perfectly.
Hood bumper
p/n: 70-0013-42
Pads, hood hold-down clamp, mount on clamp swivels to hold hood corners in. Set of four (4) rubber pads in solid brass, chrome plated cups.
Front Apron Crossbar Grommets
p/n: 70-1131-45
This Front Apron Crossbar Grommet pair is designed from the original part for superior fitment, finish and function. Width: 3-1/2" inches. Height: 3-1/2" inches.
Body Mounting Pad
p/n: 70-0298-48
Pads, body mounting for front bracket, right and left. Three eighths (3/8) inch by two and three fourths (2-3/4) inch by four (4) inches with two (2) collars and retaining rings. Two (2) required per car.
Vacuum Brake Cylinder Rod Boot
p/n: 70-0010-24
This Vacuum Brake Cylinder Rod Boot is designed from the original part for superior fitment and seal. Made from durable rubber to original configuration.
Engine Mount Pad
p/n: 70-1162-11
This Front Engine Mount Pad pair is designed for cars with round cone type front engines. For V-12 and V-16 models.
Cadillac Motors pedal pad
p/n: 70-0076-22
Cadillac Motors pedal pads. Authentic straight diamond pattern. Especially good copy, fine detail.
Firewall Grommet Set
p/n: 70-1149-21
This Firewall Grommet Set contains six (6) pieces that are intended for spark and choke rods, fuel line, oil gauge line and radiator brace rods. Designed from the original part for superior fit and seal.
Shock and Stabilizer Seal
p/n: 70-1184-33
Seals, shock absorber and rear stabilizer link. Eight (8) piece set. Width: 1.1875 inches.
Front Bumper Grommet
p/n: 70-0103-28
Grommets, front bumper. Theses are for the round, tubular bumper support.