Body Weatherstrip Kit
p/n: 90-3179-90
This Body Weatherstrip Kit includes the major weatherstrip components and some other essential parts needed for the body of your restoration project.
Hardtop Roof Rail Weatherstrips
p/n: 70-0966-68
This Hardtop Roof Rail Weatherstrip pair fits on the roof of the vehicle and seals the side window when the window is fully raised.
Engine Mount Service – Revulcanization Only
p/n: 70-0548-11
This Revulcanization Service Only is designed to restore your Front Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Rear door vent weatherstrip
p/n: 70-3452-74
Rear door vent window seals. Authentic configuguration, fully molded with integral metal cores. Note: Order our #60-0682-56 division post seal strip separately.
Rear Door Weatherstrips
p/n: 70-2254-72
This Rear Door Weatherstrip pair is the primary door to body weatherstrip. Clip on type. Contains six (6) clips.
Front Door Vent Window Weatherstrip Set
p/n: 90-0426-90
This four (4) piece Front Door Vent Window Weatherstrip Set contains the main vent window and division post weatherstrips. All of the pieces were designed from original parts for a precise, factory fit.
Windshield Gasket
p/n: 27-0055-50
This Windshield Gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit.
Rear Window Gasket
p/n: 70-0739-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Prop shaft support service
p/n: 70-0748-27
Bearing support bracket assembly, drive shaft center bearing. Revulcanization service only. .
Cadillac Master Parts List 1957 - 1964 (Reprint)
p/n: 07-1443-07
This 1957-1964 Cadillac Master Parts List - Two (2) Volume set licensed Detroit Iron reprint provides the most comprehensive repair information in paper format. This OEM PARTS manual reproduction provides detailed original part numbers, part assembly diagrams / illustrations and part textual details for all vehicle subsystems.
Front Door Vent Window Weatherstrips
p/n: 38-0092-55
These Front Door Vent Window Weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Front Door Weatherstrips
p/n: 70-0825-72
Door edge weatherstrip with molded ends. This part is the primary door to body weatherstrip. Includes six (6) clips for easy installation. Made of top quality rubber.
Splash Apron / A-Arm Dust Shield Filler Set
p/n: 70-2495-45
This fourteen (14) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Cowl Drain Gutter
p/n: 70-0780-73
Gutter, windshield lower corner, left and right. Rubber with metal core as original. Seven and three quarters long (7-3/4").Length: 7.75 inches.
Fender Skirt Edge Weatherstrip
p/n: 70-0154-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Hood To Cowl Weatherstrip
p/n: 70-2130-42
This Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. This weatherstrip installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
Axle Rebound Pad
p/n: 70-2225-32
Bumper, rear spring axle impact. Located on frame rail. Rubber only, does not include metal retaining clips or bolts.
Beltline Weatherstrips
p/n: 70-1121-61
These Beltline Weatherstrips (sometimes called "scraper seal") come in a three (3) foot pair. For use on front, rear, and quarter windows without a chrome reveal molding at the window beltline. Available in 3ft pair.
Front coil spring pad
p/n: 70-2302-35
Pad, front coil spring insulator cushion. Fully molded, mounts at top of front coil springs.
1935-1974 Cadillac Factory Parts Manual, CD
p/n: 07-1346-07
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Cadillac Factory parts manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
Outer Beltline Weatherstrip
p/n: 70-0802-61
This Outer Beltline Weatherstrip is fully molded with EPDM rubber over a corrosion resistant brass metal core. These window scrapers are for models with the chrome strip on the door. Designed like original with attaching tabs.
Beltline Weatherstrip
p/n: 70-1120-61
This Beltline Weatherstrip comes in a six (6) foot length for the outer beltline (sometimes called "scraper seal"). For use on front, rear, and quarter windows without a chrome reveal molding at the window beltline. Available in 6ft lengths.
Rear Door Pillar Filler
p/n: 70-0837-79
This Rear Door Pillar Filler pair is designed from the original part for superior fitment and sealing. This left and right weatherstrip filler mounts at the bottom of the rear side window, lower leading edge to seal the rear quarter window. Also known as a door jamb seal.
Beltline Weatherstrip Channel
p/n: 70-0651-58
This Beltline Weatherstrip Channel is a five (5) foot length of rigid channel with a flocked rubber lip and a flat stainless bead. Can be used as the inner beltline weatherstrip on front doors, rear doors and quarter windows.
Upper Lock Pillar Weatherstrips
p/n: 70-1762-73
This Upper Lock Pillar Weatherstrip pair is designed from the original part for superior fitment and seal. These auxillary door weatherstrips fit to the lock pillar vertical.
Run Channel Upper Bumper
p/n: 70-1044-62
This run channel upper bumper is manufactured as original with brass metal core.
Vent Division Bar Weatherstrip
p/n: 70-0849-56
Front vent window division post seal. Eleven and one half inches (11.5") and one half inch high. Fully molded with metal core and attaching tabs.
Vent division bar weatherstrip
p/n: 60-0682-56
Vent window division post seal. Fully molded with metal core and attaching tabs. This part fits opposite the glass run channel and seals the vent window when the vent is closed. Note: used for front door vent on 1958 Chevrolet and Pontiac li
Side Window Vertical Leading Edge
p/n: 70-0806-80
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised.
Door Hinge Seals
p/n: 70-1460-70
This Door Hinge Seal installs on the front door hinge pillar at the beltline. These seals are sold as a pair for the left and right side.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0773-WT
This Steele exclusive Peel-N-Stick Trunk Weatherstrip is designed from the original part for superior fitment and seal. This easy to install weatherstrip mounts around the full perimeter of the trunk directly to the body.
Body / Cowl to Fender Seals
p/n: 70-2787-43
This Body / Cowl to Fender Seals pair is designed from the original part for superior fitment and function. Filler seal pieces are die cut from quality masticated rubber to authentic original dimensions.
Suspension arm bumper
p/n: 70-1021-32
Bumper, front or rear suspension, upper. Uses two (2) per car on front suspension, one (1) per car on rear.
Trunk Weatherstrip
p/n: 70-0773-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Front Stabilizer Bar End Link Set
p/n: 70-2110-33
A twenty-two (22) piece Front Stabilizer Bar End Link set. Comes complete with fasteners, metal sleeves, metal cup washers and black rubber bushings. One (1) end link set for both sides of stabilizer bar on one (1) car.
Radiator Upper Support Filler
p/n: 70-2502-45
This single piece Radiator Upper Support Filler is designed from the original part for superior fitment and function. Filler piece is die cut from quality masticated rubber to authentic original dimensions. Fits at radiator to radiator upper support.
Radiator Mounting Pad
p/n: 70-0963-31
Radiator mounting pad, insulator. Up to four (4) used per car.Length: 6.0 inches.
Metal Sleeved Grommet
p/n: 70-0203-41
Flanged rubber grommet with metal sleeve bushing. Used as part of the accelerator relay lever. Also used from 1959-61 on all Cadillac models as a bushing for the windshield wiper relay lever adaptor.
Body Mount Isolator Pad
p/n: 70-0929-48
Body Mount Isolator Pad - Rubber with metal core and locating collar as original part. Part dimensions = Two and three sixteenths inch (2 3/16") square by one inch (1") overall height with thirteen sixteenths inch (13/16") inside bolt diameter. Does not include any fastener hardware.
Door Handle Gasket Set
p/n: 70-0771-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Taillight Lens Gaskets
p/n: 70-3235-15
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between taillight lens & taillight housing.
Directional and Parking Light Lens Gaskets
p/n: 70-3115-16
This Turn Signal and Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Signal / Parking Light Lens and the Signal / Parking Light Housing or Bezel.
Hood Bumper
p/n: 70-0770-42
Bumper, fender to hood. Correct detail with ridges as original. Four (4) required per car.Length: 1.3125 inches.
Back Up Light Lens Gaskets
p/n: 70-3234-17
This Back Up Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the back-up light lens and the back-up light housing or light bezel.
Taillight Lens Gaskets - In Fin
p/n: 70-3502-15
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. These reproduction gaskets fit between the taillight lens & taillight housing in fin.
Beltline Guide Plate - Plastic
p/n: 50-0384-62
This Beltline Guide Plate is designed from the original part for superior fitment and function. High quality plastic plate attaches to various outer beltline window scraper weatherstrips.
Front Door Lock Pillar Filler
p/n: 70-0834-79
This Front Door Lock Pillar Filler pair is designed from the original part for superior fitment and sealing. This left and right weatherstrip filler seals the bottom at the front of the rear side window. Also known as a door jamb seal.
Hood Bumper
p/n: 70-0907-42
Bumper, hood front aligning. Correct design with proper screw thread.Height: 2.50 inches.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Headlight Bucket to Fender Seals
p/n: 70-3085-14
This two (2) piece Headlight Bucket to Fender Seal pair is designed from the original part for superior fitment and seal. Die cut from original style masticated rubber for a like factory fit.
Body Mount Isolator
p/n: 70-2232-48
Isolator, body mounting to chassis. Fully molded rubber. One and seven eighths inch (1 7/8") outside diameter by fifteen sixteenths inch (15/16") inside hole diameter by nine sixteenths inch (9/16") height.
Body Mounting Pad
p/n: 70-2233-48
Pad, body mounting to chassis. Fully molded rubber. One and seven eighths inch (1 7/8") outside diameter by eleven sixteenths inch (11/16") inside hole diameter by nine sixteenths inch (9/16") height.
Body Mounting Pad
p/n: 70-2234-48
Pad, body mounting to chassis. Fully molded rubber, square type. Six (6) or more are used per car. Two and three sixteenths inch (2 3/16") square by three fourths inch (3/4") inside diameter hole by one half inch (1/2") inch height.
Plastic Guide Plate
p/n: 50-0385-58
Plastic guide plate, attaches to various outer scraper weatherstrips.Length: 1.625 inches. Width: .625 inches.
Rear View Mirror Mounting Pad
p/n: 70-3083-70
This single Rear View Mirror Mounting Pad To Door gasket is designed from the original part for superior fitment and seal. The gasket is precision die cut to the original specifications. This gasket is for one (1) door mounted rear view mirror.
Headlight dimmer switch pad
p/n: 70-0930-14
Pad, headlight dimmer switch. Rubber slip-over cover for floor mounted switch.
Spark Plug Wire Spacer
p/n: 70-0394-21
This Spark Plug Wire Spacer is designed from the original part for superior fitment and function. This spacer fits spark plug wires into the organizer bracket.
Multi-Purpose Clips
p/n: 70-4802-45
A ten (10) piece set of Multi-Purpose Clips. Commonly used to retain Hood to Cowl Weatherstrips or Inner Fender Splash Panels.
Window Stop Stem Bumper
p/n: 33-0540-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and function. Designed as a window stop cushion for front and rear door, rear side and quarter windows as needed.
13/16" Door Weatherstrip with Clips
p/n: 70-1245-73
This Door Weatherstrip is made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Brown Door Lock Knob
p/n: 70-0660-70
This is the Knob or push button for the inside door lock. The part fits over 1/8" steel rod to door lock. Neutral brown color that may be lacquered with other colors as required. A hard rubber part fits many different vehicles.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
2-5/8" Run Channel Mohair Liner
p/n: 70-2863-58
This Run Channel Mohair Liner helps to reline the guide bars on the lock side of hardtops and convertibles. This mohair liner comes with a rubber backing and installs with adhesive to the division bars and channel. Available by the foot.
1-1/16" Trunk Weatherstrip
p/n: 70-0346-85
This Trunk Weatherstrip is designed from an original part for a specific application but has many uses outside of its original purpose. Available by the foot.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0510-WT
This Peel-N-Stick Trunk Weatherstrip is made from a high-quality EPDM sponge rubber. Available by the foot.
1" Trunk Weatherstrip
p/n: 70-0510-85
This Trunk Weatherstrip was designed from an original part for a specific application but has many uses outside of its original purpose. Available by the foot.
13/16" Door Weatherstrip without Clips
p/n: 70-1244-73
This Door Weatherstrip is made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
2-1/4" Body Hole Plug
p/n: 35-0863-45
This Body Hole Plug is fully molded and designed from the original part for superior fitment and seal. Designed for the trunk, however the generic shape makes this plug usable for a variety of applications.
5/8" Door Weatherstrip without Clips
p/n: 70-1111-73
This Door Weatherstrip made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Stabilizer Link or Shock Grommet
p/n: 70-0737-33
This Stabilizer Link or Shock Grommet is designed from the original part for superior fitment and usage. Fully molded rubber.
Door Drain Hole Seal
p/n: 70-1042-70
Weatherstrip, door bottom drain hole.Length: 3.625 inches. Width: .40625 inches.
1/16" Sash Channel Filler - Cork
p/n: 70-1115-57
This 1/16" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.