Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Front Stabilizer Bushing
p/n: 60-0088-34
This Front Stabilizer Bushing pair is fully molded from EPDM dense rubber to ensure durability. Used to connect the stabilizer bar to the vehicle frame. Two (2) required per car.
Door Weatherstrip
p/n: 60-0114-73
Weatherstrip, door bottom, sponge constant section, solid skin surface, superior quality. Sold in six (6) foot strips only.Length: 72.0 inches.
Headlight Mounting Pad
p/n: 70-0201-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. This pad acts as the headlight adjusting collar. Sold as a pair.
Fuel Filler Neck Grommet
p/n: 60-0040-41
This Fuel Filler Neck Grommet is a fully molded rubber, grommet slightly angled with a retaining flange. Three and five sixteenths inch (3-5/16") outside width by three and one half inch (3-1/2") outside length by two and one eighth inch (2-1/8") inside hole diameter.
Horn Button Contact Set
p/n: 60-0492-21
This is a three (3) piece Horn Button Contact set which is designed from the original part for superior fitment and function. Renews the operation of the steering wheel horn blowing ring.
Cowl Vent Hose
p/n: 60-0457-54
Hose, cowl vent drain. Seems to be correct for some models rather than our #50-0259-54.
License Light Mounting Pad
p/n: 60-0074-17
Mounting pad, license light. Three and one eighth (3-1/8) inch by eight and seven eighths (8-7/8) inch. Fully detailed.Length: 8.875 inches.
Backup Light Mounting Pad
p/n: 60-0072-17
Mounting pads, back up lights, elliptic, sharp beaded edge. One and five sixteenths (1-5/16) inch by two and seven eighths (2-7/8) inch.Length: 2.
Cowl vent weatherstrip
p/n: 70-0143-54
Gasket, cowl vent. Perfect copy of original, not a sponge substitute, top quality material.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Hood to Cowl Weatherstrip
p/n: 60-0090-42
This Hood to Cowl Weatherstrip is extruded from a high quality dense rubber for a durable and proper seal. This pair comes with pre-drilled holes for easy installation.
Center Division Bar Chrome Molding Retainer
p/n: 70-0373-51
Center Division Bar Chrome Molding Retainer for outside windshield center post stainless molding. Use with original stainless molding and clips. Length: 15-1/2 inches. Width: 1-1/4 inches.
Gravel Shield Bumper Set
p/n: 60-0146-30
This Gravel Shield Bumper Set is used as a rear bumper deflector. Also used between the radiator grille and the lower panel. Two (2) required per car. Designed from the original part for superior fitment and seal.
Parking Light Lens Gasket
p/n: 60-0207-17
Gasket, parking light lens. Top quality one eighth (1/8) inch sponge.Length: 5.50 inches. Width: 1.75 inches.
Taillight Lens Gasket
p/n: 60-0100-15
Gasket, taillight lens.Length: 5.125 inches. Width: 1.875 inches.
Starter Button Cover
p/n: 60-0322-21
This Starter Button Cover is designed from the original part for an authentic fit, finish, and appearance. A push on replacement to rod. Two (2") inch outside diameter.
Clutch and Brake Pedal Bumpers
p/n: 60-0104-24
This Clutch and Brake Pedal Bumper is designed from the original part for superior fitment and function. Pedal shank rides under floorboard. One and one-eighth (1-1/8") inch clearance for pedal shaft.
Door Check Link Rod End Stop
p/n: 70-0479-70
End nut, check link (rubber bar with steel bar insert). Three fourths (3/4) inch by three fourths (3/4) inch by two (2) inch threaded five sixteenths (5/16) inch. (For round stop nut, see our #70-0326-70).
Steering column seal
p/n: 60-0478-36
Seal, steering column at toe board, for steering column housing and shifter control shaft jacket. Top quality sponge rubber, accurately cut.
Starter Pedal Button Cover
p/n: 60-0166-21
This Starter Button Pedal Cover is designed from the original part for an authentic fit, finish, and appearance. Rubber slip over type for old metal. Two (2") inch outside diameter.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Brake Master Cylinder Push Rod Boot
p/n: 60-0180-24
This Brake Master Cylinder Push Rod Boot is made from high-quality Nitrile rubber for a precise, factory like fit for your classic vehicle. Manufactured to OEM specifications to install for an authentic fit and finish.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.