Starter Pedal Bellows
p/n: 60-0487-21
Bellows, starter pedal shaft-to-floorboard. One and three fourths (1-3/4) inch by two and one fourth (2-1/4) inch.Length: 2.25 inches. Width: 1.75 inches.
Trunk Hinge Mounting Pad
p/n: 60-0139-87
Pad, trunk hinge mounting, upper and lower. Four (4) piece set.
Starter Button Cover
p/n: 60-0322-21
This Starter Button Cover is designed from the original part for an authentic fit, finish, and appearance. A push on replacement to rod. Two (2") inch outside diameter.
Clutch and Brake Pedal Bumpers
p/n: 60-0104-24
This Clutch and Brake Pedal Bumper is designed from the original part for superior fitment and function. Pedal shank rides under floorboard. One and one-eighth (1-1/8") inch clearance for pedal shaft.
Firewall Grommet
p/n: 60-0013-20
This Firewall Grommet is used to run the wiring harness and speedometer cable through the toe board. Designed from the original part for superior fit and seal.
Firewall Grommet
p/n: 60-0010-45
This Firewall Grommet is the oblong four (4) hole style. The grommet fits the steel retainer for the throttle and choke cables, and the oil and temperature lines.
Starter Pedal Button Cover
p/n: 60-0166-21
This Starter Button Pedal Cover is designed from the original part for an authentic fit, finish, and appearance. Rubber slip over type for old metal. Two (2") inch outside diameter.
Body Mounting Pad
p/n: 60-0028-48
Pad, front body mounting. Right angle style. Fully molded rubber. Four and one sixteenth inch (4 1/16") length by three and seven eighths inch (3 7/8") width by one half inch (1/2") inside hole diameters by one fourth inch (1/4") height.
Steering Column Cushion - Brown
p/n: 60-0012-89
This Steering Column Cushion grommet is designed from the original part for an authentic fit, finish, and appearance. For the steering column to cowl U-bolt clamp. Brown rubber. For Black see 60-0012-36
Brake Master Cylinder Push Rod Boot
p/n: 60-0180-24
This Brake Master Cylinder Push Rod Boot is made from high-quality Nitrile rubber for a precise, factory like fit for your classic vehicle. Manufactured to OEM specifications to install for an authentic fit and finish.
Steering Column Cushion - Black
p/n: 60-0012-36
This Steering Column Cushion grommet is designed from the original part for an authentic fit, finish, and appearance. For the steering column to cowl U-bolt clamp. Black rubber. For Brown see 60-0012-89.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Steering Column Gasket
p/n: 60-0014-36
This Steering Column to Toe Board Gasket is designed from the original part for superior fitment and sealing. This part fits around the steering column to seal the column through the body floor pan.
Exhaust Support Grommet
p/n: 60-0031-13
This Exhaust Support Grommet is designed from the original part for superior fitment and usage. The OEM direct fit application is as a rear and middle muffler exhaust support hanger.
2" Firewall Grommet
p/n: 70-0158-21
This Firewall Grommet is used to run the ignition switch conduit through the firewall. Designed from original parts for excellent workmanship.
1-11/16" Firewall Grommet
p/n: 32-0196-21
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
Door Handle Ferrule
p/n: 70-0111-69
A Ferrule for three fourths (3/4") inch outside door handles. Chrome plated brass. Used for outside door handle or outside trunk handle.
Spark plug retaining ring
p/n: 30-0352-21
Retaining ring, spark plug wire. Two (2) per car.Chevrolet 1935-48 Retaining ring, spark plug wire. Two (2) per car. All models.
Door Check Link Rod End Stop
p/n: 70-0326-70
End stop and pad, door check link rod. Rubber with embedded steel plate, five sixteenths (5/16) inch diameter thread. Most models with rod type door checks.
Body Mounting Pad
p/n: 60-0027-48
Pad, side body mounting. Fully molded rubber, rectangular. Two and seven-sixteenths inch (2-7/16") outside length by one and five-eights inch (1-5/8") outside width by one-fourth inch (1/4") height.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Bumper Support Bar Pad
p/n: 60-0544-30
A fully molded rubber Bumper Support Bar Pad. Thes part installs between the bumper support bar and bumper face bar at the mounting bolts. Use as required, eight (8) are needed for most cars.
Electrical Terminal Boot
p/n: 30-0279-41
This Electrical Terminal Boot is designed from the original part for superior fitment and seal. This boot works to cover and protect electrical terminal connections.
Wiper Transmission Gasket
p/n: 60-0029-53
Gasket, windshield wiper transmission mounting. Replaces #4073727.
Wiring Harness Loom Grommet
p/n: 60-0255-14
This Grommet is designed from the original part for superior fitment. The grommet ideally works for the headlight or taillight wiring loom through body sheet metal. Four (4) to six (6) grommets per vehicle.