Accelerator Rod Seal
p/n: 60-0136-41
Grommet, accelerator rod through toe board. Brass core and center bushing as original.
Brown Steering Column Grommet
p/n: 60-0102-89
Grommet, steering column at floor (column shift). Brown rubber. For black see our #60-0102-36.
Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Fuel Neck Grommet
p/n: 60-0040-41
Grommet, fuel filler neck. Fully molded rubber, slightly angled with retaining flange. Three and five sixteenths inch (3-5/16") outside width by three and one half inch (3-1/2") outside length by two and one eighth inch (2-1/8") inside hole diameter.
Cowl Vent Hose
p/n: 60-0457-54
Hose, cowl vent drain. Seems to be correct for some models rather than our #50-0259-54.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
License Light Mounting Pad
p/n: 60-0205-17
Mounting pad trunk license light. Not an original item. But many owners wish to pad this light from the paint job. Good fit, perfect bead form.
Cowl vent weatherstrip
p/n: 70-0143-54
Gasket, cowl vent. Perfect copy of original, not a sponge substitute, top quality material.
Fuel Filler Neck Grommet
p/n: 60-0022-41
This Fuel Filler Neck Grommet is fully molded rubber and slightly angled. Three and eleven sixteenths inch (3-11/16") outside diameter by two and three sixteenths inch (2-3/16") top hole diameter by two and five eighths inch (2-5/8") bottom hole diameter.
Horn Button Contact Cushion
p/n: 60-0192-21
Cushion, standard steering wheel horn button contact. Two and one half (2-1/2) inch diameter.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Steering Column Grommet
p/n: 60-0102-36
Grommet, steering column at floor (column shift). Black rubber. For brown see our #60-0102-89.
Hood to Cowl Weatherstrip
p/n: 60-0056-42
This Hood to Cowl Weatherstrip is extruded from a high quality dense rubber for a durable and proper seal. This seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.
Battery Carrier Edge Liner
p/n: 60-0112-21
Edge liner, battery carrier cover.Length: 42.0 inches. Width: .25 inches. Height: .6875 inches.
Trunk Hinge Mounting Pad
p/n: 70-1231-87
Mounting pads, trunk hinge. Four (4) piece set.Length: 8.8125 inches.
Trunk Hinge Mounting Pad
p/n: 60-0139-87
Pad, trunk hinge mounting, upper and lower. Four (4) piece set.
Taillight Lens Gasket
p/n: 60-0147-15
Gasket, taillight lens. Two and three fourths (2-3/4) inch diameter.
Starter Button
p/n: 60-0322-21
Starter button, push on replacement to rod. Two (2) inch outside diameter.
License Light Mounting Pad and Grommet Set
p/n: 60-0337-17
This License Light Mounting Pad and Grommet Set is designed from the original part for superior fitment and function. Mounting Pad for the license light to trunk lid. The Grommet is for the license bracket spacer post.
Stabilizer Shaft Link Bushing
p/n: 60-0317-33
This Stabilizer Shaft Link Bushing works to support the vehicle front stabilizer or sway bar shaft. Six (6) required per vehicle.
Taillight Mounting Pad
p/n: 60-0495-15
Pad, taillight bracket to fender. Can be used for right or left hand. Two and one half (2-1/2) inch by three and five eighths (3-5/8) inch overall.
Brake and Clutch Pedal Bumpers
p/n: 60-0104-24
Bumpers, brake and clutch pedal shank, rides under floorboard. One and one eighth (1-1/8) inch clearance for pedal shaft. Compare with part 60-0579-24.
Trunk Handle Grommet
p/n: 50-0183-87
Grommet, trunk handle bezel-thru-trunk lid. Special size, one (1) inch inside diameter.Buick 1937 Grommet, trunk handle bezel-thru-trunk lid.
Windshield Division Bar Gasket
p/n: 70-0098-52
This Windshield Division Bar Gasket is designed from the original part for superior fitment and seal. Part combines inner and outer gasket in one piece as original. For seventeen (17") inch to (20") inch lengths.
Firewall Grommet
p/n: 60-0010-45
This Firewall Grommet is the oblong four (4) hole style. The grommet fits the steel retainer for the throttle and choke cables, and the oil and temperature lines.