Battery Cable Grommet
p/n: 40-0333-21
Grommet, battery hot cable through frame. Three fourths (3/4) inch inside diameter for one and three sixteenths (1-3/16) inch hole through frame.
Trunk Handle Mounting Pad
p/n: 40-0226-85
Pad, truck handle escutcheon.Length: 2.875 inches. Width: 1.375 inches.
Body Mounting Pad
p/n: 40-0324-48
Cushion, used as either a body mounting pad or for all body bolt nuts, below brackets. Fully molded rubber. Two inch (2") outside diameter by one half inch (1/2") inside hole diameter by three eighths inch (3/8") height.
Roof Insert Seal
p/n: 20-0102-45
Seal, top insert for closed cars without turret top. Fits groove between cloth top center panel and steel surround. Available by the foot.
Door Bumper
p/n: 70-1156-71
Door Side Bumper made from EPDM Dense rubber. Clip retained. Appears identical to Atwood #107, #208. Width: 1-1/2" inches. Height: 1-5/16"
Door opening step grommet
p/n: 40-0125-49
Grommet, door sill mat retainer at lower door opening. All sill plates with metal stud retainer. (Included in our #40-0542-49 set).
Door Bumper
p/n: 40-0154-70
Bumper, door side. One and one fourth (1-1/4) inch long by one (1) inch wide. Similar to our #40-0010-70, but different workface.Length: 1.0 inches.
1/8" x 7/8" Fabric Hood Lacing
p/n: 60-0578-42
This 1/8" x 7/8" Fabric Hood Lacing is high quality original style woven cotton hood to cowl lacing. This lacing has the slot to install a wire insert or fasten with rivets if so found originally. Available by the foot to accommodate any job.
2-1/16" Spare Wheel Carrier Grommet
p/n: 32-0253-37
This Spare Wheel Carrier Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber. Designed for spare wheel carrier mounting bracket.
3/16" x 3/4" Fabric Hood Lacing
p/n: 70-2221-42
This 3/16" x 3/4" Fabric Hood Lacing is made of a high-quality original style woven cotton. Available by the foot to accommodate any job.
7/8" Window Weatherstrip
p/n: 40-0054-99
This Window Weatherstrip is typically used on the rear window and rear fixed quarter window. Used on cars with chrome reveal molding where the reveal molding lays over the pinchweld seal. Available by the foot.
Front and Rear Door Bumper
p/n: 34-0025-42
High quality steel core Front and Rear Door Bumper for front and rear body hinge pillar. Mounted by screw. For auxiliary use only where needed to prevent door rattles. Replaces factory #372341.
1" Frame Hole Plug
p/n: 35-0166-44
Plug, for holes in right hand frame rail when car is left hand drive. (Frames were punched for both right hand and left hand drive).
Door Bumper
p/n: 34-0131-37
Bumper, front door above the upper hinge on the upper radius of the door. Stiff-backed, retained by screw, mounted on door only.
Spring Shackle Bushing
p/n: 40-0183-32
Bushing, spring and shackle, front and rear leaf springs. Eight (8) or twelve (12) required per car.Length: 1.25 inches. Height: 1.25 inches.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Rear Spring Thrust Washer
p/n: 40-0526-32
Thrust washer, rear spring. "Silent Block". Three sixteenths (3/16) inch thick. Seven eighths (7/8) inch by one and five eighths (1-5/8).
2-5/8" Run Channel Mohair Liner
p/n: 70-2863-58
This Run Channel Mohair Liner helps to reline the guide bars on the lock side of hardtops and convertibles. This mohair liner comes with a rubber backing and installs with adhesive to the division bars and channel. Available by the foot.
Door Weatherstrip
p/n: 70-1292-73
This Door Weatherstrip is used on the bottom of the door opening. Available by the foot.
Door Weatherstrip
p/n: 70-1448-73
This Door Weatherstrip for the door sill is made of an extruded dense rubber. Available by the foot.