Coil wire sleeve
p/n: 40-0336-21
Nipple, sparkplug wire at sparkplug, for right angle plug terminal. This is an exact copy of the style used at the time. Not a modernistic makeover.
Door - Gravel Shield - Running Board Weatherstrip
p/n: 60-0054-73
This Door - Gravel Shield - Running Board Weatherstrip is a anti-squeak bulb type extrusion with fitment for General Motors vehicles. A twelve (12) foot strip made of high-quality EPDM dense rubber and designed from original parts for superior fitment, finish and function.
Door and Trunk Handle Gasket
p/n: 40-0132-70
Pad, door handle escutcheon. Two and five sixteenths (2-5/16) inch by one and seven sixteenths (1-7/16) inch.
Door Bumper
p/n: 40-0010-70
Pad, door jamb, fully detailed. One and one eighth (1-1/8) inch long, one and one fourth (1-1/4) inch wide.Length: 1.125 inches. Width: 1.25 inches.
Door Bumper
p/n: 40-0037-70
Pad, door jamb. One and nine sixteenths (1-9/16) inch long by one and one eighth (1-1/8) inch wide.Length: 1.625 inches. Width: 1.0625 inches.
Door Bumper
p/n: 40-0154-70
Bumper, door side. One and one fourth (1-1/4) inch long by one (1) inch wide. Similar to our #40-0010-70, but different workface.Length: 1.0 inches.
Door Check Strap
p/n: 40-0535-70
Strap, door check. T-type, special heavy duty construction of rubber with multiple ply webbing and molded-in steel crossbar. Full length as original with one eighth (1/8) inch by seven eighths (7/8) inch steel crossbar.
Fender Skirt Edge Weatherstrip
p/n: 40-0279-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Fender Welting 1/4" Bead - 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty-five (25) foot roll. Typically used to attach two (2) fenders to body.
Fender Welting 1/4" Bead - 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body.
Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Fender Welting with 3/16" Bead - 50ft
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Gearshift Boot
p/n: 40-0111-88
Boot, base of gearshift lever. Black rubber. For brown see our #40-0111-89. Made separately to fit most of our gearshift floorplates. Copied from original.
Hood Corner Pad
p/n: 40-0127-42
Pads, hood corners, brass core. Approximately 80 degree angle. Integral tabs for installing.Length: 1.50 inches.
Hood Corner Pad
p/n: 40-0128-42
Pads, hood corners. Square type, brass core. Integral installation tabs. 90 degree angle, used on front or rear corners, as required.
Horn trumpet grommet
p/n: 40-0086-21
Grommet for trumpet horn wire through motor cover. Close reproduction. Two (2) per car.
Rear Bumper Grommet
p/n: 40-0112-30
Grommets, rear bumper symmetrical, right and left. Perfect detailing on both inner and outer surfaces. Fully molded rubber.
Rear Spare Wheel Carrier Seal
p/n: 40-0141-37
Grommet, rear spare wheel carrier.Some models require 3 pieces (1-1/2 prs).Length: 3.375 inches.
Rear Spring Thrust Washer
p/n: 40-0525-32
Thrust washer, rear spring. "Silent Block". Three sixteenths (3/16) inch thick. One (1) inch by one and three fourths (1-3/4) inch.
Rear Spring Thrust Washer
p/n: 40-0526-32
Thrust washer, rear spring. "Silent Block". Three sixteenths (3/16) inch thick. Seven eighths (7/8) inch by one and five eighths (1-5/8).
Rear Window Gasket
p/n: 70-0084-77
This Rear Window Gasket comes in a seven foot, six inch (7' 6") strip and mounts around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Shock Absorber Arm Bushing
p/n: 60-0106-32
This Shock Absorber Arm Bushing is designed from the original part for superior fitment and function. Manufactured to OEM original standards.
Shock or Stabilizer Link Cross Pin Bushing
p/n: 50-0220-32
This Shock or Stabilizer Link Cross Pin Bushing is designed from the original part for superior fitment and function. A rubber bushing for shock absorber link cross pin or stabilizer cross link pin.
Side Mount Clamp Cushion
p/n: 40-0138-37
Cushion, sidemount clamp. Two and one eighth (2-1/8) inch by four and five eighths (4-5/8) inch.Length: 4.625 inches. Width: 2.125 inches.