Running Board Matting Cover
p/n: 20-1601-49
This Running Board Matting Cover pair is designed from the original part for an authentic fit and finish.
Windshield Gasket
p/n: 20-1606-50
This Windshield Gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it. It also has the slot to accommodate the outer edge's decorative molding.
Front Door Vent Window Weatherstrip Set
p/n: 20-1615-55
This Front Door Vent Window Weatherstrip Set contains the main and division post seals for the vent windows and the base extension pieces for the frame. They are designed and molded from original parts for superior fitment and seal.
Door Weatherstrip Kit
p/n: 20-1655-72
Door edge weatherstrip. This set is the primary door to body perimeter weatherstrip.
Trunk Weatherstrip
p/n: 20-1685-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Body To Frame Mounting Pad Set
p/n: 20-1597-48
This fifteen (15) piece Body to Frame Mounting Pad set is designed from the original parts for superior fitment and function.
Body to Frame Webbing
p/n: 20-1599-48
This Body to Frame Webbing is designed from the original part for superior fitment and function. This webbing is used to shim the body to the frame. Also used as a noise reducer material. Webbing is two (2) inch wide, twenty-five (25) foot long roll.
Fender Skirt Edge Weatherstrip
p/n: 20-0111-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish and sealing function. Two five (5) foot strips that fit between the rear wheel fender skirt and rear quarter panel.
Door weatherstrip
p/n: 20-1644-73
Weatherstrips, open car door hinge. Door seals molded to fit hinge area.
Beltline Weatherstrips
p/n: 40-0539-57
This Beltline Weatherstrip pair installs on the left and right doors to wipe the inside and outside of the windows when the glass is lowered. Flexible, pile lined, rubber covered, with a black bead. Available in 3ft pair.
Floor Board Seals
p/n: 20-1595-88
This Floor Board Seal set contains all of the correct sealing components for the front floor boards.
Fender Welting
p/n: 20-1590-44
This black Fender Welting is designed from the original part for superior fitment and seal. This welting material fits between the fenders and the vehicle body. Thirty (30) foot roll.
Engine and Transmission Mount
p/n: 20-1978-11
This Engine and Transmission Mount is designed from the original part for superior fitment and function. This engine mount works to absorb and isolate engine and driveline vibrations. The set services one mount. 1937-1941 require four (4) sets for both Front and Rear. 1942-1948 require two (2) sets.
Cowl Vent Gasket
p/n: 20-1613-54
This Cowl Vent Gasket is designed from the original part for superior fitment and seal. Manufactured to OEM specifications to install for an authentic fit and finish.
Hood Bumper Set
p/n: 20-1588-42
This twelve (12) piece Hood Bumper set is designed from the original parts for superior fitment and function.
Fender Welting
p/n: 20-1591-44
This black Fender Welting is designed from the original part for superior fitment and seal. This welting material fits between the fenders and the vehicle body. Eight (8) foot length.
Glovebox Door Bumper Stops
p/n: 20-1698-88
Bumper stops for the glovebox door - lower. Rubber Coated Steel like original. This part prevents the glovebox door from opening too far, reduces paint-chipping.
Steering Column Floorplate
p/n: 20-1694-88
Seal, steering column tube. Installs on top of floor mat.
Cowl Lacing Rubber Seal
p/n: 20-1587-42
This Cowl Lacing Rubber Seal is designed from the original part for superior fitment and seal. This seal mounts at the rear of the engine bay directly to the body to seal between the firewall and hood.
Windshield Post to Door Seals
p/n: 20-1608-73
Seal, windshield post to door. Goes on windshield post below convertible window channel retainer.
Channel Filler Weatherstrip
p/n: 20-1633-62
Seal, door glass and stainless frame special. Top, bottom, and sides for one door.Width: .375 inches. Height: .625 inches.
Fuel Tank Filler Neck Connection Hose
p/n: 20-1584-39
This Fuel Tank Filler Neck Connection Hose is designed from the original part for superior fitment and function. Connects the fuel tank to the fuel filler pipe.
Clutch and Brake Pedal Arm Seals
p/n: 20-1564-23
This Clutch and Brake Pedal Arm Seal pair is designed from the original part for an authentic fit, finish, and appearance. For Clutch and Brake pedal arms to floorboard.
Clutch and Brake Pedal Pads
p/n: 20-1563-22
This reproduction Clutch and Brake Pedal Pad pair screws to the pedal arms for a precise, factory fit. With authentic concentric circle design, pads are a perfect reproduction to replace worn original pedal pads.
Door Check Link Rod End Stop
p/n: 20-1640-70
This Door Check Link Rod End Stop is designed from the original part for superior fit and function. This door stop fits between the door and body to limit the swing opening of the door preventing overtravel. Door check arm and bumper. Enough for one door.
Door Weatherstrip - Lower
p/n: 20-1651-73
This Lower Door Weatherstrip is designed from the original part for superior fitment and seal. This weatherstrip mounts in the lower door seal retainer. One (1) piece cuts to do two (2) doors.
Front or Rear Axle Bumper
p/n: 20-1576-33
This Front or Rear Axle Bumper is designed from the original part for superior fitment, finish and function. An exact reproduction of original. Typically order two per vehicle.
Tie Rod Dust Covers
p/n: 20-2484-36
This Tie Rod Dust Cover, drag link seal, is sold as a four (4) piece set. The seals are designed from originals for proper fitment.
Cowl Firewall Grommet
p/n: 20-1560-20
This Cowl Firewall Grommet fits into the upper section of the firewall for the main wiring harness. Also used to run the dash wires on the firewall and through the firewall.
Upper Engine Mount
p/n: 20-1538-11
This Front or Rear Upper Engine Mount reproduction is designed from the original part for superior fitment and durability. This mount fits between the engine and chassis to support the engine and reduce harmonic vibrations.
Lower Engine Mount
p/n: 20-1539-11
This Lower Engine Mount is designed from original part for correct fitment and function. Rubber coated over a metal core for durability and proper engine vibration isolation.
Headlight Bucket To Fender Gasket
p/n: 20-1542-14
This Headlight Bucket To Fender Gasket is designed from the original part for superior fitment and seal. These gasket fits the headlight bucket and front fender.
Convertible Roof Rail Weatherstrip
p/n: 20-1636-65
This Convertible Roof Rail Weatherstrip is designed from the original part for superior fitment and seal. This window channel seal fits between windshield posts and door. Also fits along the top irons. This part is one (1) each. Five (5) individual pieces are required for the complete top.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32") inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons and other project uses.
Taillight Lens Gasket
p/n: 20-0411-15
Gaskets, taillight lens. Cork.Ford Truck 1948-56 Gaskets, lens to housing. Ford Cars 1941 Gaskets, taillight lens.
Wiper Transmission Gasket
p/n: 20-1609-53
Seal, wiper pivot shaft to roof or cowl. Small type. Replaces factory #11A-17541. Note: this part is used as a wiper pivot shaft to roof in 1937-1939. It is used as a wiper pivot shaft to cowl in 1941-1948.
Wiper Transmission Gasket
p/n: 20-1610-53
Seal, wiper pivot shaft to cowl. Large type. Replaces factory #7C-17541.
Engine Mount Washer
p/n: 20-0442-11
This Front Upper Engine Mount Washer is made of steel. The large upper engine mount insulator sits in this special washer. Fits all Ford 6 cylinder and Flathead V-8 models.
Windshield Wiper Hose Grommet
p/n: 20-1611-20
This Windshield Wiper Hose Grommet is used to run the wiper hose through the firewall. Designed from original part so it fits correctly.
Door Jamb Bumper
p/n: 20-2366-71
This Door Jamb Bumper is a quality reproduction of the original factory part. This rubber bumper mounts into a slot in the door jamb to cushion the door closure. Two (2) required per door.
1-1/4" Body Hole Plug
p/n: 20-1039-21
This Body Hole Plug is designed from the original part for superior fitment, finish and function. This plug is made from high quality EPDM dense rubber to provide excellent durability. This body plug covers a sheet metal hole that is one and one fourth (1-1/4") inches in diameter.
Choke, Throttle and Starter Wiper Motor Grommet
p/n: 20-1561-20
This Choke, Throttle or Wiper Motor Grommet is designed from the original part for superior fitment and usage. A multi-purpose grommet, it fits into the vehicles firewall to provide a secure passthrough for the mechanical choke, throttle rod or wiper motor wiring.
Engine Mount Washer
p/n: 20-0440-11
This Upper Engine Mount Washer is made of steel. Reproduction is designed from the original part to fit correctly.
Glovebox bumper
p/n: 20-2391-88
Bumpers, glovebox door.Ford Cars 1960 Bumpers, fuel tank door. All Galaxie models. Ford Truck 1935-47 Bumpers, glovebox door.
Door Check Arm Bumper
p/n: 20-1639-70
This Door Check Arm Bumper is designed from the original part for superior fitment and function. This rubber with arm slot bumper mounts on the door check arm. Works to cushion the door swing.