1-1/4" Body Hole Plug
p/n: 20-1039-21
This Body Hole Plug is designed from the original part for superior fitment, finish and function. This plug is made from high quality EPDM dense rubber to provide excellent durability. This body plug covers a sheet metal hole that is one and one fourth (1-1/4") inches in diameter.
Beltline Weatherstrips
p/n: 40-0539-57
This Beltline Weatherstrip pair installs on the left and right doors to wipe the inside and outside of the windows when the glass is lowered. Flexible, pile lined, rubber covered, with a black bead. Available in 3ft pair.
Body to Frame Webbing
p/n: 20-1599-48
This Body to Frame Webbing is designed from the original part for superior fitment and function. This webbing is used to shim the body to the frame. Also used as a noise reducer material. Webbing is two (2) inch wide, twenty-five (25) foot long roll.
Channel Filler Weatherstrip
p/n: 20-1633-62
Seal, door glass and stainless frame special. Top, bottom, and sides for one door.Width: .375 inches. Height: .625 inches.
Choke, Throttle and Starter Wiper Motor Grommet
p/n: 20-1561-20
This Choke, Throttle or Wiper Motor Grommet is designed from the original part for superior fitment and usage. A multi-purpose grommet, it fits into the vehicles firewall to provide a secure passthrough for the mechanical choke, throttle rod or wiper motor wiring.
Clutch and Brake Pedal Arm Seals
p/n: 20-1564-23
This Clutch and Brake Pedal Arm Seal pair is designed from the original part for an authentic fit, finish, and appearance. For Clutch and Brake pedal arms to floorboard.
Clutch and Brake Pedal Pads
p/n: 20-1563-22
This reproduction Clutch and Brake Pedal Pad pair screws to the pedal arms for a precise, factory fit. With authentic concentric circle design, pads are a perfect reproduction to replace worn original pedal pads.
Convertible Roof Rail Weatherstrip
p/n: 20-1636-65
This Convertible Roof Rail Weatherstrip is designed from the original part for superior fitment and seal. This window channel seal fits between windshield posts and door. Also fits along the top irons. This part is one (1) each. Five (5) individual pieces are required for the complete top.
Cowl Firewall Grommet
p/n: 20-1560-20
This Cowl Firewall Grommet fits into the upper section of the firewall for the main wiring harness. Also used to run the dash wires on the firewall and through the firewall.
Cowl Lacing Rubber Seal
p/n: 20-1587-42
This Cowl Lacing Rubber Seal is designed from the original part for superior fitment and seal. This seal mounts at the rear of the engine bay directly to the body to seal between the firewall and hood.
Cowl Vent Gasket
p/n: 20-1613-54
This Cowl Vent Gasket is designed from the original part for superior fitment and seal. Manufactured to OEM specifications to install for an authentic fit and finish.
Door Check Arm Bumper
p/n: 20-1639-70
This Door Check Arm Bumper is designed from the original part for superior fitment and function. This rubber with arm slot bumper mounts on the door check arm. Works to cushion the door swing.
Door Check Link Rod End Stop
p/n: 20-1640-70
This Door Check Link Rod End Stop is designed from the original part for superior fit and function. This door stop fits between the door and body to limit the swing opening of the door preventing overtravel. Door check arm and bumper. Enough for one door.
Door Jamb Bumper
p/n: 20-2366-71
This Door Jamb Bumper is a quality reproduction of the original factory part. This rubber bumper mounts into a slot in the door jamb to cushion the door closure. Two (2) required per door.
Door weatherstrip
p/n: 20-1644-73
Weatherstrips, open car door hinge. Door seals molded to fit hinge area.
Door Weatherstrip - Lower
p/n: 20-1651-73
This Lower Door Weatherstrip is designed from the original part for superior fitment and seal. This weatherstrip mounts in the lower door seal retainer. One (1) piece cuts to do two (2) doors.
Door Weatherstrip Kit
p/n: 20-1655-72
Door edge weatherstrip. This set is the primary door to body perimeter weatherstrip.
Engine Mount
p/n: 20-1978-11
This Engine Mount is designed from the original part for superior fitment and function. This engine mount works to absorb and isolate engine and driveline vibrations. The set services one mount. 1937-1941 require four (4) sets for both Front and Rear. 1942-1948 require two (2) sets.
Engine Mount Washer
p/n: 20-0440-11
This Upper Engine Mount Washer is made of steel. Reproduction is designed from the original part to fit correctly.
Engine Mount Washer
p/n: 20-0442-11
This Front Upper Engine Mount Washer is made of steel. The large upper engine mount insulator sits in this special washer. Fits all Ford 6 cylinder and Flathead V-8 models.
Fender Skirt Edge Weatherstrip
p/n: 20-0111-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish and sealing function. Two five (5) foot strips that fit between the rear wheel fender skirt and rear quarter panel.
Fender Welting
p/n: 20-1590-44
This black Fender Welting is designed from the original part for superior fitment and seal. This welting material fits between the fenders and the vehicle body. Thirty (30) foot roll.
Fender Welting
p/n: 20-1591-44
This black Fender Welting is designed from the original part for superior fitment and seal. This welting material fits between the fenders and the vehicle body. Eight (8) foot length.
Floor Board Seals
p/n: 20-1595-88
This Floor Board Seal set contains all of the correct sealing components for the front floor boards.
Front Axle Bumper
p/n: 20-1577-33
This Front Axle Bumper is a quality reproduction of the original factory part. These bottoming bump stops are dense rubber blocks that mount with a stud to a front axle bracket.
Front Bumper Arm Grommets
p/n: 20-1566-28
This four (4) piece Front Bumper Arm Grommet set is designed from the originals for an authentic fit and finish.
Front Door Vent Window Weatherstrip Set
p/n: 20-1615-55
This Front Door Vent Window Weatherstrip Set contains the main and division post seals for the vent windows and the base extension pieces for the frame. They are designed and molded from original parts for superior fitment and seal.
Front or Rear Axle Bumper
p/n: 20-1576-33
This Front or Rear Axle Bumper is designed from the original part for superior fitment, finish and function. An exact reproduction of original. Typically order two per vehicle.
Fuel Tank Filler Neck Connection Hose
p/n: 20-1584-39
This Fuel Tank Filler Neck Connection Hose is designed from the original part for superior fitment and function. Connects the fuel tank to the fuel filler pipe.
Glovebox bumper
p/n: 20-2391-88
Bumpers, glovebox door.Ford Cars 1960 Bumpers, fuel tank door. All Galaxie models. Ford Truck 1935-47 Bumpers, glovebox door.
Glovebox Door Bumper Stops
p/n: 20-1698-88
Bumper stops for the glovebox door - lower. Rubber Coated Steel like original. This part prevents the glovebox door from opening too far, reduces paint-chipping.
Headlight Bucket To Fender Gasket
p/n: 20-1542-14
This Headlight Bucket To Fender Gasket is designed from the original part for superior fitment and seal. These gasket fits the headlight bucket and front fender.
Hood Bumper Set
p/n: 20-1588-42
This twelve (12) piece Hood Bumper set is designed from the original parts for superior fitment and function.
Inner Fender Bumper
p/n: 20-1594-45
This six (6) piece Inner Fender Bumper set is designed from the original part for superior fitment and seal. These rubber bumpers plug into the holes in the inner fender apron to help eliminate squeaks and rattles.