Cowl Firewall Grommet
p/n: 20-1560-20
This Cowl Firewall Grommet fits into the upper section of the firewall for the main wiring harness. Also used to run the dash wires on the firewall and through the firewall.
Cowl Lacing Rubber Seal
p/n: 20-1587-42
This Cowl Lacing Rubber Seal is designed from the original part for superior fitment and seal. This seal mounts at the rear of the engine bay directly to the body to seal between the firewall and hood.
Cowl Vent Gasket
p/n: 20-1613-54
This Cowl Vent Gasket is designed from the original part for superior fitment and seal. Manufactured to OEM specifications to install for an authentic fit and finish.
Door Bumper
p/n: 20-0067-71
This Door Bumper is designed from the original part for an authentic fit, finish and function. Installs on back edge of door. Usually two (2) to eight (8) per vehicle.
Door Bumper
p/n: 70-2725-71
Bumper, door, upper rear corner attaches to the door. Two (2) needed per car.
Door Bumper - Lower
p/n: 70-3308-71
This Lower Door Bumper is designed from the original part for superior fitment and function. Bumper pushes into slot on door at bottom.
Door Bumper Set
p/n: 20-2365-71
Set, convertible striker bumper. Consists of four (4) bumpers for striker plates and four (4) bumpers for above and below striker.
Door Bumper, Upper / Lower
p/n: 20-2825-71
This Door Bumper is a quality reproduction of the original factory part. Upper / Lower push-in type. Four (4) required per car.
Door Check Arm Bumper
p/n: 20-1639-70
This Door Check Arm Bumper is designed from the original part for superior fitment and function. This rubber with arm slot bumper mounts on the door check arm. Works to cushion the door swing.
Door Check Link Rod End Stop
p/n: 20-1640-70
This Door Check Link Rod End Stop is designed from the original part for superior fit and function. This door stop fits between the door and body to limit the swing opening of the door preventing overtravel. Door check arm and bumper. Enough for one door.
Door drain hole seal
p/n: 70-3034-70
Seal, door inner panel drain. Attaches to bottom of door with one (1) carrot retainer on either end.
Door handle gasket
p/n: 20-2584-69
Pads, outside door handle. Set includes four (4) pieces for two (2) handles.
Door Hinge Weatherstrips
p/n: 20-1643-73
This Door Hinge Weatherstrip pair is designed from the original parts for superior fitment and sealing. These door edge weatherstrips are molded specifically to fit the door hinge area of the vehicle.
Door Jamb Bumper
p/n: 20-2366-71
This Door Jamb Bumper is a quality reproduction of the original factory part. This rubber bumper mounts into a slot in the door jamb to cushion the door closure. Two (2) required per door.
Door Lower Weatherstrips
p/n: 20-1652-73
This three (3) piece Lower Door Weatherstrip set is designed from the original part for superior fitment and seal. Use full-length for front doors, cut third piece in half to complete installation for both rear doors.
Door Vent Window Foot
p/n: 20-2556-62
This Door Vent Window Foot installs at the base of the front door vent window frame. Sold as a pair.
Door weatherstrip
p/n: 20-1647-73
Weatherstrips, closed car back of door. Vertical section on lock side of door.
Door weatherstrip
p/n: 70-2717-73
Seal, lower door. Mounts to bottom of door assembly. Runs from just below the lower hinge and down the length of the bottom of the door.
Door Weatherstrip
p/n: 70-2720-73
This Door Weatherstrip is for the upper door front auxiliary. The pair mounts on door where the window frame comes in contact with the A-post.
Door Weatherstrip
p/n: 20-0104-72
This Door Weatherstrip pair is designed from the original parts for superior fitment and seal. These primary door weatherstrips mount (push pin) to seal the driver and passenger doors when closed.
Door Weatherstrip
p/n: 20-1190-72
This Door Weatherstrip pair is the primary door to body weatherstrip. These door weatherstrips mount, with pre-installed pins, directly on the vehicle body. Ends are molded with metal cores.
Door Weatherstrip
p/n: 70-3367-72
Door edge weatherstrip. This part is the primary door to body weatherstrip.
Door weatherstrip
p/n: 20-2368-73
Seals, lower door. Comes as a three (3) piece set but is enough to do all four (4) doors. The seal for the rear doors will need to be cut in half.
Door Weatherstrip
p/n: 70-2718-73
This Door Weatherstrip pair is designed from the original parts for superior fitment and seal. These primary front door weatherstrips push-on like original to seal the driver and passenger doors when closed.
Door Weatherstrip
p/n: 70-2719-73
This Door Weatherstrip seals the upper door at the drip rail. It attaches to the body of the car. Located on A-post and continues across roof line and down the B-post.
Door weatherstrip
p/n: 20-1644-73
Weatherstrips, open car door hinge. Door seals molded to fit hinge area.
Door weatherstrip
p/n: 20-1649-73
Weatherstrip, back of door, vertical section. Material enough for all four doors, cut to fit at installation.
Door Weatherstrip - Lower
p/n: 20-1651-73
This Lower Door Weatherstrip is designed from the original part for superior fitment and seal. This weatherstrip mounts in the lower door seal retainer. One (1) piece cuts to do two (2) doors.
Door Weatherstrip Kit
p/n: 20-1655-72
Door edge weatherstrip. This set is the primary door to body perimeter weatherstrip.
Door Weatherstrip Set
p/n: 20-1653-72
This nine (9) piece Door Weatherstrip Set is designed from the original part for superior fitment and seal. This set contains the primary door / door edge to body perimeter weatherstripping.
Door Weatherstrip Set
p/n: 20-1654-72
This Door Weatherstrip set is designed from the original part for superior fitment and seal. These Front and Rear door edge perimeter serve as the primary door to body weatherstripping for all four (4) doors.
Door Weatherstrips
p/n: 20-2827-72
This Door Weatherstrip is designed from the original parts. These gaskets are the the primary door to body weatherstrips. Molded ends with metal cores. Includes two (2) pins.
Door Weatherstrips
p/n: 20-2828-72
This Door Weatherstrip pair is designed from the original parts for superior fitment and seal to keep the elements out and reduce road noise while driving. Molded ends with metal cores.
Door Weatherstrips
p/n: 20-2829-72
This Door Weatherstrip pair is designed from the original parts for superior fitment and seal to keep the elements out and reduce road noise while driving. Molded ends with metal cores.
Emergency Brake Cable Grommet
p/n: 20-2310-24
This Emergency Brake Cable Grommet is used when running the brake cable to the frame. Made from high-quality dense rubber to provide excellent durability.
Emergency Brake Cable Grommet
p/n: 20-2299-20
This Emergency Brake Cable Grommet is used for running the emergency brake cable and the speedometer cable through the firewall. Made from high-quality dense rubber to provide excellent durability.
Engine Mount
p/n: 20-1978-11
This Engine Mount is designed from the original part for superior fitment and function. This engine mount works to absorb and isolate engine and driveline vibrations. The set services one mount. 1937-1941 require four (4) sets for both Front and Rear. 1942-1948 require two (2) sets.
Fender Skirt Edge Weatherstrip
p/n: 20-3017-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Fender Skirt Edge Weatherstrip
p/n: 20-0111-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish and sealing function. Two five (5) foot strips that fit between the rear wheel fender skirt and rear quarter panel.
Fender Skirt Edge Weatherstrip
p/n: 20-3019-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Fender Washer - Rubber
p/n: 20-2191-44
This quality rubber Fender Washer is designed from the original part for superior fitment and function. For the mounting of the rear fender. Large type, one and one half (1-1/2") inches diameter.
Fender Washer - Rubber
p/n: 20-2190-44
This quality rubber Fender Washer is designed from the original part for superior fitment and function. For the mounting of the front fender. Small type. One and one fourth (1-1/4") inches diameter.
Fender Welting
p/n: 20-1591-44
This black Fender Welting is designed from the original part for superior fitment and seal. This welting material fits between the fenders and the vehicle body. Eight (8) foot length.
Fender Welting
p/n: 20-1590-44
This black Fender Welting is designed from the original part for superior fitment and seal. This welting material fits between the fenders and the vehicle body. Thirty (30) foot roll.
Firewall To Hood Bumpers
p/n: 20-2758-42
These Firewall To Hood Bumpers are a quality reproduction of the original factory part. Includes attaching screws. Three (3) piece set.
Firewall to Hood Weatherstrip
p/n: 70-3123-42
This Firewall to Hood Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. Installs with the pre-installed clips on the front edge of the cowl.
Firewall to Hood Weatherstrip
p/n: 20-2750-42
This Firewall to Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This weatherstrip installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
Firewall to Hood Weatherstrip
p/n: 70-4200-43
This Firewall to Hood Weatherstrip is designed from the original part for superior fitment and seal. This seal has the proper cowl radius to fit correctly. Mounts with ten (10) pre-installed clips at the rear of the engine bay directly to the body.
Firewall To Hood Weatherstrip
p/n: 20-2751-42
This Firewall To Hood Weatherstrip is designed from the original part for superior fitment and seal. This seal mounts at the rear of the engine bay firewall directly to the body to keep water and debris out.
Firewall to Hood Weatherstrip
p/n: 20-2760-42
This Firewall To Hood Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This weatherstrip installs at the rear of the engine bay to seal between the hood and the vehicle firewall.
Firewall to Hood Weatherstrip - Cowl Lacing
p/n: 20-3006-43
This Firewall to Hood Weatherstrip - Cowl Lacing is designed from the original part for superior fitment and seal. This seal mounts with installation tacks at the rear of the engine bay firewall directly to the body.
Firewall to Hood Weatherstrip - Cowl Lacing
p/n: 20-1456-42
This Firewall to Hood Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This single piece cowl lacing seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl / firewall.
Firewall to Hood Weatherstrip - Cowl Lacing
p/n: 20-1088-42
This Firewall to Hood Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This single piece cowl lacing seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl / firewall.
Firewall to Hood Weatherstrip - Cowl Lacing
p/n: 20-1089-42
This Firewall To Hood Weatherstrip - Cowl Lacing is designed from the original part for superior fitment and seal. An exact reproduction using dense and sponge rubber extrusion with fasteners imbedded in place as original.
Firewall to Hood Weatherstrip - Cowl Lacing
p/n: 20-2183-42
This Firewall to Hood Weatherstrip - Cowl Lacing is designed from the original part. This cowl lacing mounts with screws at the rear of the engine bay firewall directly to the body to seal between the hood and vehicle body cowl.
Firewall to Hood Weatherstrip - Cowl Lacing
p/n: 20-1457-42
This Firewall to Hood Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This single piece cowl lacing seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl / firewall.
Firewall to Hood Weatherstrip - Cowl Lacing
p/n: 20-3007-43
This Firewall to Hood Weatherstrip - Cowl Lacing is designed from the original part for superior fitment and seal. A reproduction using dense rubber extrusion and tack fasteners.
Firewall to Hood Weatherstrip - Cowl Lacing
p/n: 20-1091-42
This Firewall To Hood Weatherstrip - Cowl Lacing mounts under the rear of the hood on the cowl panel. This is a die-cut extrusion with pre-installed clips as original.
Firewall to Hood Weatherstrip - Cowl Lacing
p/n: 70-3374-42
This Firewall to Hood Weatherstrip - Cowl Lacing is designed from the original part for superior fitment and seal. Measuring 67-1/2” long x 1-1/4” wide to provide complete coverage.
Flexible Run Channel
p/n: 20-1146-58
This Flexible Run Channel helps to eliminate window rattle, provides a smooth sliding surface for glass movement, and works to protect the glass. Stainless steel beaded. Available in sixty (60) inch strips.
Flexible Run Channel - 60 Inch
p/n: 20-1619-58
Channel, side window glass, vertical run. Flexible, felt lined, rubber covered channel. Available 60" lengths.
Front & Rear Door Weatherstrip
p/n: 20-2593-72
This Door Weatherstrip set is designed from the original parts for superior fitment and seal. Includes front and rear door seals. These door seals mount directly to the left and right side doors to seal the full perimeter of the doors against the vehicle body when the door is closed.
Front + Rear Door Weatherstrip
p/n: 20-3114-72
Door edge weatherstrip. Includes front and rear doors. This part is the primary door to body weatherstrip.
Front and Rear Door Weatherstrip Set
p/n: 20-1181-72
Door edge weatherstrip. Includes both front and rear door seals. These parts are the primary door to body weatherstrips. Contains plastic pins and metal tabs that are attached to the door weatherstrips. Also includes four (4) screws.
Front and Rear Door Weatherstrips
p/n: 20-3116-72
This Front and Rear Door Weatherstrip set is designed from the original parts for superior fitment and seal. These primary door weatherstrips mount (glue-on) directly to the four (4) doors acting to seal the full perimeter of the doors against the vehicle body when the door is closed.
Front Axle Bumper
p/n: 20-1577-33
This Front Axle Bumper is a quality reproduction of the original factory part. These bottoming bump stops are dense rubber blocks that mount with a stud to a front axle bracket.
Front Axle Bumpers
p/n: 20-2175-33
This Front Axle Bumper pair is designed from the original part for an authentic fit, finish and function.
Front Bow Weatherstrip
p/n: 20-2798-64
This Front Bow Weatherstrip is designed from the original part for superior fitment and seal. This header seal installs directly to the windshield frame to seal between the soft top and the top of the windshield.
Front Bumper Arm Grommets
p/n: 20-1566-28
This four (4) piece Front Bumper Arm Grommet set is designed from the originals for an authentic fit and finish.
Front Door At Beltline Weatherstrips
p/n: 20-0094-73
This Front Door At Beltline Weatherstrip pair is designed from the original part for superior fitment and seal. This inner dog leg door seal fits at the door front at beltine inner.
Front Door Lower Weatherstrip
p/n: 70-2837-73
This Front Door Lower Weatherstrip pair is designed from the original parts for superior fitment and seal. This seal mounts to bottom of door assembly and runs from just below the lower hinge and down the length of the bottom of door.
Front Door Upper Weatherstrip
p/n: 70-2730-73
This Front Door Upper Weatherstrip attaches to the body of the car along the drip rail. The seal mounts on the A-post and continues across roof line and down the B-post. Door weatherstrip pair is designed from the original parts for superior fitment and seal.
Front Door Vent Window Set
p/n: 90-0439-90
This four (4) piece Front Door Vent Window Set contains the main vent window seals and division post seals. The main seals are molded in the shape of the window and designed from original parts for superior fitment and seal.
Front Door Vent Window Set
p/n: 90-0450-90
This four (4) piece Front Door Vent Window Set contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Front Door Vent Window Set
p/n: 90-0444-90
This four (4) piece Front Door Vent Window Set contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Front Door Vent Window Set
p/n: 90-0324-90
This four (4) piece Front Door Vent Window Set contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Front Door Vent Window Set
p/n: 90-0312-90
This four (4) piece Front Door Vent Window Set contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Front Door Vent Window Set
p/n: 90-0311-90
This four (4) piece front Front Door Vent Window Set contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Front Door Vent Window Set
p/n: 90-0323-90
This four (4) piece Front Door Vent Window Set contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Front Door Vent Window Set
p/n: 90-0301-90
This four (4) piece Front Door Vent Window Set contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.