Door to Body Conduit, Power Window Wiring
p/n: 70-1538-70
This Door to Body Conduit set is designed from the original part for superior fitment and function. This is the sheathing conduit for the power windows wiring from the front door to the body through the hinge pillar.
Front Door Weatherstrip
p/n: 82-0074-72
Door edge weatherstrip. This part is the primary door to body weatherstrip.
Front Engine Mount
p/n: 60-0462-11
This front Engine Mount is a new replacement mount manufactured to meet or exceed factory specifications. For six (6) cylinder models only.
Hinge Pillar Weatherstrip
p/n: 82-0073-63
Convertible Hinge Pillar Weatherstrip - Attaches to the body and seals between the A-pillar post and the front section of the door or vent window frame when the door is closed.
Hood To Cowl Weatherstrip
p/n: 82-0067-43
This Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This weatherstrip installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
Hydraulic Pump Mounting Pad
p/n: 70-0946-67
This Hydraulic Pump Mounting Pad is designed from the original part for superior fitment and function. For folding top hydraulic pump mount. Special design to hold pump mounting bracket to floor pan. Four (4) pads needed per car. Height: 1" inch.
Lock Cylinder Gasket
p/n: 60-0641-69
This Lock Cylinder Gasket is die cut from one-thirty-second (1/32) inch neoprene.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Multi-Purpose Clips
p/n: 70-4802-45
A ten (10) piece set of Multi-Purpose Clips. Commonly used to retain Hood to Cowl Weatherstrips or Inner Fender Splash Panels.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0774-WT
This Peel-N-Stick Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0510-WT
This Peel-N-Stick Trunk Weatherstrip is made from a high-quality EPDM sponge rubber. Available by the foot.
Radiator Mounting Insulator Pads
p/n: 70-2238-31
A four (4) piece set of Radiator Mounting Insulator Pads. For use on all four corners of the radiator. For vehicle models with three (3) wide core radiators.
Rocker Panel Inner Drain Cover
p/n: 70-2392-45
This Rocker Panel Inner Drain Cover pair is designed from the original part for superior fitment and seal. Fully molded with proper attaching teeth and flap.
Side Window Vertical Leading Edge Weatherstrips
p/n: 50-0344-80
This Side Window Vertical Leading Edge Weatherstrips pair is designed from the original part for superior fitment and seal. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised.
Splash Apron / A-Arm Dust Shield
p/n: 70-3067-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Stabilizer Bar Bushings
p/n: 70-4678-34
This Stabilizer Bar to Frame Bushing pair may fit either front or rear stabilizer / sway bars depending on the vehicle. Manufactured with quality materials to original specifications.
Transmission Filler Flaps
p/n: 70-3686-25
This Transmission Filler Flap pair is designed from the original part for superior fitment and seal. For Cutlass and 442 models with automatic transmission. Two (2) piece filler flap pair located where the frame meets the firewall on the right and left sides.
Transmission Mount
p/n: 70-2058-25
This Transmission Mount is a new aftermarket replacement mount manufactured to meet or exceed factory specifications.. One (1) required per vehicle.
Trunk Weatherstrip
p/n: 70-0774-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk directly to the body.
U Jamb Lock Pillar Filler
p/n: 82-0064-79
This U Jamb Lock Pillar Filler seals the bottom of the rear side window, and may also be known as a door jamb seal.
Vent Window Pivot Post Rivet
p/n: 70-4757-98
This Vent Window Pivot Post Rivet is used to replace the hinge pivot rivet for both left and right vent window assemblies. Commonly used for General Motors car and truck models.
Vent Window Rebuild Set
p/n: 70-4801-70
This Vent Window Rebuild Set includes glass setting tape (1/16 thick), hinge pivot step rivet pair, and a rivet peening punch. The set has enough materials for both the passenger side and driver side vent window assemblies.
Vent Window Rivets and Setting Tool
p/n: 70-4789-70
This Vent Window Rivet pair and Setting Tool includes the peening punch and step rivets to replace the hinge pivot rivet for both left and right vent window assemblies.
Vent Window Weatherstrip Set
p/n: 70-4074-55
This four (4) piece Vent Window Weatherstrip Set is for both driver and passenger doors of GM A-Body 2 door models. All of the pieces were designed from original parts for a precise, factory like fit.
Window Felt Beltline Weatherstrips
p/n: 80-0094-57
This is a Standard material style replacement side window horizontal weatherstrip set (also known as beltline weatherstrip). This eight (8) piece set includes the inner and outer felt beltline weatherstrips for each side and quarter window.