Body Weatherstrip Kit
p/n: 90-3183-90
This Body Weatherstrip Kit includes the major weatherstrip components and some other essential parts needed for the body of your restoration project.
Body Weatherstrip Kit
p/n: 90-3174-90
This Body Weatherstrip Kit includes the major weatherstrip components and some other essential parts needed for the body of your restoration project.
Convertible Roof Rail Weatherstrip Set
p/n: 70-2403-65
This seven (7) piece Convertible Roof Rail Weatherstrip Set fits on the folding roof of the vehicle and seals the side window when the window is fully raised.
Convertible Roof Rail Weatherstrip Set
p/n: 60-0612-65
This seven (7) piece Convertible Roof Rail Weatherstrip Set fits on the folding roof of the vehicle and seals the side window when the window is fully raised.
Front Door Vent Window Weatherstrip Set
p/n: 90-0426-90
This four (4) piece Front Door Vent Window Weatherstrip Set contains the main vent window and division post weatherstrips. All of the pieces were designed from original parts for a precise, factory fit.
Front Door Weatherstrips
p/n: 70-0819-72
This Door Edge Weatherstrip with molded ends pair is the primary weatherstrip which seals the door to body. Includes four (4) pins and twenty-six (26) sockets for easy installation.
Windshield Gasket
p/n: 70-0858-50
This Windshield Gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit.
Front Door Vent Window Weatherstrips
p/n: 38-0092-55
These Front Door Vent Window Weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Convertible Hinge Pillar Weatherstrips
p/n: 70-0850-63
This Convertible Hinge Pillar Weatherstrip pair attaches to the body and seals between the A-pillar post and the front section of the door or vent window frame when the door is closed. Includes two (2) pins.
Front Engine Support Insulator
p/n: 25-0041-11
This Front Engine Support Insulator is designed from original for an exact aftermarket replacement.
Cowl Drain Gutter
p/n: 70-0780-73
Gutter, windshield lower corner, left and right. Rubber with metal core as original. Seven and three quarters long (7-3/4").Length: 7.75 inches.
Beltline Weatherstrip
p/n: 70-0961-60
This Beltline Weatherstrip is thick pile lined without chrome bead. Available in 4ft pairs.
Taillight Gasket
p/n: 25-0078-15
Gasket, taillight housing to body. Note: Two (2) pairs are required for Starfires. All other vehicles need one (1) pair.
Beltline Weatherstrips
p/n: 70-1121-61
These Beltline Weatherstrips (sometimes called "scraper seal") come in a three (3) foot pair. For use on front, rear, and quarter windows without a chrome reveal molding at the window beltline. Available in 3ft pair.
U Jamb Door Lock Pillar Fillers
p/n: 60-0571-79
This U Jamb Door Lock Pillar Filler pair is designed from the original part for superior fitment and sealing. This right and left weatherstrip filler mounts at the bottom of the rear side window, lower leading edge to seal the rear quarter window. Also known as a Door U Jamb Seal.
Run Channel Upper Bumper
p/n: 70-0779-62
This run channel upper bumper is manufactured as original with a brass metal core and molded for a precise, factory fit. The seal is installed at the top of the front door vent window frame on the division post.
Outer Beltline Weatherstrip
p/n: 50-0488-61
This Outer Beltline Weatherstrip is fully molded with EPDM rubber over a corrosion resistant brass metal core. These window scrapers are for models with the chrome strip on the door. Designed like original with attaching tabs.
Beltline Weatherstrip
p/n: 70-1120-61
This Beltline Weatherstrip comes in a six (6) foot length for the outer beltline (sometimes called "scraper seal"). For use on front, rear, and quarter windows without a chrome reveal molding at the window beltline. Available in 6ft lengths.
Beltline Weatherstrip Channel
p/n: 70-0651-58
This Beltline Weatherstrip Channel is a five (5) foot length of rigid channel with a flocked rubber lip and a flat stainless bead. Can be used as the inner beltline weatherstrip on front doors, rear doors and quarter windows.
Side Window Vertical Leading Edge
p/n: 60-0644-80
This Side Window Vertical Leading Edge weatherstrip pair attaches to the vertical edge of the rear side windows when the rear side windows are fully raised. Molded authentic rubber construction with metal core, this part does not include the chrome piece.
Vent Division Bar Weatherstrip
p/n: 70-0849-56
Front vent window division post seal. Eleven and one half inches (11.5") and one half inch high. Fully molded with metal core and attaching tabs.
Door Hinge Seals
p/n: 70-1460-70
This Door Hinge Seal installs on the front door hinge pillar at the beltline. These seals are sold as a pair for the left and right side.
Taillight Lens Gasket
p/n: 25-0079-15
Gasket, taillight lens to housing. Shear die cut sponge rubber.Length: 10.0 inches.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0773-WT
This Steele exclusive Peel-N-Stick Trunk Weatherstrip is designed from the original part for superior fitment and seal. This easy to install weatherstrip mounts around the full perimeter of the trunk directly to the body.
Trunk Weatherstrip
p/n: 70-0773-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Firewall Grommet
p/n: 25-0099-20
This Firewall Grommet is used to run accessory wiring through the firewall. Designed from the original part for superior fit and seal.
Radiator Mounting Pad
p/n: 70-0963-31
Radiator mounting pad, insulator. Up to four (4) used per car.Length: 6.0 inches.
Radiator Mounting Pad
p/n: 25-0087-31
Insulator, radiator support. Two (2) to four (4) used per car.Length: 6.75 inches.
Fuel Filler Neck Grommet
p/n: 70-1439-39
This Fuel Filler Neck Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler neck between the filler neck and vehicle body. Fits as original.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Rocker Panel Inner Drain Cover
p/n: 70-2392-45
This Rocker Panel Inner Drain Cover pair is designed from the original part for superior fitment and seal. Fully molded with proper attaching teeth and flap.
Vent Window Rebuild Set
p/n: 70-4801-70
This Vent Window Rebuild Set includes glass setting tape (1/16 thick), hinge pivot step rivet pair, and a rivet peening punch. The set has enough materials for both the passenger side and driver side vent window assemblies.
Beltline Guide Plate - Plastic
p/n: 50-0384-62
This Beltline Guide Plate is designed from the original part for superior fitment and function. High quality plastic plate attaches to various outer beltline window scraper weatherstrips.
Hood Bumper
p/n: 25-0076-42
This Hood Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure. Six (6) required per car.
Body Mount Isolator Pad
p/n: 50-0507-48
Isolator, body mounting. Fully molded rubber. Two inches (2") outside diameter by seven eighths inch (7/8") inside hole diameter by three fourths inch (3/4") height.
Plastic Guide Plate
p/n: 50-0385-58
Plastic guide plate, attaches to various outer scraper weatherstrips.Length: 1.625 inches. Width: .625 inches.
Multi-Purpose Clips
p/n: 70-4802-45
A ten (10) piece set of Multi-Purpose Clips. Commonly used to retain Hood to Cowl Weatherstrips or Inner Fender Splash Panels.
Window Stop Stem Bumper
p/n: 33-0540-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and function. Designed as a window stop cushion for front and rear door, rear side and quarter windows as needed.
Vent Window Rivets and Setting Tool
p/n: 70-4789-70
This Vent Window Rivet pair and Setting Tool includes the peening punch and step rivets to replace the hinge pivot rivet for both left and right vent window assemblies.
5/8" Door Weatherstrip with Clips
p/n: 70-1112-73
This Door Weatherstrip with Clips is made made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
13/16" Door Weatherstrip with Clips
p/n: 70-1245-73
This Door Weatherstrip is made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Brown Door Lock Knob
p/n: 70-0660-70
This is the Knob or push button for the inside door lock. The part fits over 1/8" steel rod to door lock. Neutral brown color that may be lacquered with other colors as required. A hard rubber part fits many different vehicles.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32") inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons and other project uses.
2-5/8" Run Channel Mohair Liner
p/n: 70-2863-58
This Run Channel Mohair Liner helps to reline the guide bars on the lock side of hardtops and convertibles. This mohair liner comes with a rubber backing and installs with adhesive to the division bars and channel. Available by the foot.
Brown Door Lock Knob
p/n: 70-0354-70
This is the knob or button for the inside door lock control rod. Neutral brown color rubber, 3/32 inch hole. The part fits many different vehicles.
1-1/16" Trunk Weatherstrip
p/n: 70-0346-85
This Trunk Weatherstrip is designed from an original part for a specific application but has many uses outside of its original purpose. Available by the foot.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0510-WT
This Peel-N-Stick Trunk Weatherstrip is made from a high-quality EPDM sponge rubber. Available by the foot.
1" Trunk Weatherstrip
p/n: 70-0510-85
This Trunk Weatherstrip was designed from an original part for a specific application but has many uses outside of its original purpose. Available by the foot.
13/16" Door Weatherstrip without Clips
p/n: 70-1244-73
This Door Weatherstrip is made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
2-1/4" Body Hole Plug
p/n: 35-0863-45
This Body Hole Plug is fully molded and designed from the original part for superior fitment and seal. Designed for the trunk, however the generic shape makes this plug usable for a variety of applications.
5/8" Door Weatherstrip without Clips
p/n: 70-1111-73
This Door Weatherstrip made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
1/16" Sash Channel Filler - Cork
p/n: 70-1115-57
This 1/16" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
Quarter Window Bumper
p/n: 70-1583-62
Bumper, quarter window stop on sash channel.Length: .8125 inches. Width: .75 inches. Height: .50 inches.
1/16" Sash Channel Filler - Rubber
p/n: 70-2170-57
This 1/16" Sash Channel Filler offers the best quality rubber product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
Door or Tailgate Bumper
p/n: 33-1228-71
This Door Bumper is fully molded and designed from the original part for superior fitment. This rubber bumper attaches to the vehicle body to support / cushion the door closure. Usually requires two (2) bumpers each per vehicle.
1/32" Sash Channel Filler - Cork
p/n: 70-1114-57
This 1/32" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
1/32" Sash Channel Filler - Rubber
p/n: 70-2169-57
This 1/32" Sash Channel Filler offers the best quality rubber product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
1/4" Universal Mounting Pad
p/n: 70-0308-17
This Universal Mounting Pad is used for lights, hinges, brackets, and other bright work when no molded pad is available. Manufactured with a special edge lip to hug bright work when clamped down. Shape outline to suit application.
Door Bumper
p/n: 33-1227-71
This Door Bumper is fully molded and designed from the original part for superior fitment. The twin retainer style rubber bumper attaches to the vehicle body to support/cushion the door closure. Usually requires two (2) bumpers each per vehicle.
3/4" Floor Pan Plug
p/n: 35-0262-20
This Floor Pan Plug is fully molded and designed from the original part for superior fitment and seal. This plug is made from high-quality EPDM dense rubber to provide excellent durability. Up to twelve (12) used per vehicle.
Hydraulic Pump Mounting Pad
p/n: 70-0946-67
This Hydraulic Pump Mounting Pad is designed from the original part for superior fitment and function. For folding top hydraulic pump mount. Special design to hold pump mounting bracket to floor pan. Four (4) pads needed per car. Height: 1" inch.
1/4" Trunk Bumper
p/n: 33-0293-87
This 7/8" Trunk Bumper is a quality reproduction of the original factory part. Self-retaining bumper is manufactured to OEM specifications to install for an authentic fit, finish, and function.
Lock Cylinder Gasket
p/n: 60-0641-69
This Lock Cylinder Gasket is die cut from one-thirty-second (1/32) inch neoprene.
Vent Window Pivot Post Rivet
p/n: 70-4757-98
This Vent Window Pivot Post Rivet is used to replace the hinge pivot rivet for both left and right vent window assemblies. Commonly used for General Motors car and truck models.