Hood to Fender Bumper
p/n: 25-0091-42
This Hood to Fender Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure. Six (6) required per car.
Hood Weatherstrip Clip
p/n: 70-1255-42
Clip, hood to cowl weatherstrip. Normal usage is fourteen (14) to sixteen (16) per car as needed.
Horn trumpet grommet
p/n: 70-0302-21
Grommets, horn projector. For under hood horn brackets. Two (2) per car.
Hydraulic Pump Mounting Cushion
p/n: 70-0852-67
This Hydraulic Pump Mounting Cushion is designed from the original part for superior fitment and function. Used on models with hydraulic window lifts or a hydraulic convertible top. Two (2) to three (3) required per car.
Hydraulic Pump Mounting Pad
p/n: 70-0986-62
Mounting bracket and pad, for hydraulic pump. Number used as required.Length: 1.75 inches. Width: .8125 inches.
Hydraulic Pump Mounting Pad
p/n: 70-0946-67
This Hydraulic Pump Mounting Pad is designed from the original part for superior fitment and function. For folding top hydraulic pump mount. Special design to hold pump mounting bracket to floor pan. Four (4) pads needed per car. Height: 1" inch.
Leading Edge Weatherstrip
p/n: 70-2002-80
Rear door window vertical seals. Fully molded rubber with metal cores.
Leaf Spring to Shackle Bushings
p/n: 70-3344-35
This Leaf Spring To Shackle Bushing set is designed from the original part for superior fitment and function. This bushing installs into the leaf spring eye to fit between the rear shackle to leaf spring. This is a four (4) piece set for both rear leaf springs.
License Light Mounting Pad
p/n: 25-0045-17
Pad, rear license light body.Length: 7.0 inches. Width: 3.375 inches.
Liftgate Weatherstrip
p/n: 70-2250-85
This liftgate weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the liftgate opening directly to the body.
Lock Cylinder Gasket
p/n: 70-0955-86
Gasket, trunk lock cylinder. Steel rule die cut from one thirty seconds (1/32) inch dense rubber.
Lock Cylinder Gasket
p/n: 60-0641-69
This Lock Cylinder Gasket is die cut from one-thirty-second (1/32) inch neoprene.
Lock pillar filler
p/n: 70-0939-79
Door lock pillar seal. Longer type (4 -3/4"). This part seals the bottom of the rear side window, and may also be known as a door jamb seal. Fully molded authentic rubber construction with metal core.
Lock Pillar Water Deflector
p/n: 70-3635-62
Door panel water deflector, at lock. Fully molded for both left and right hand sides.
Lower Sash Channel Filler
p/n: 70-2844-57
This Lower Sash Channel Filler is designed from the original part for superior fitment and function. A flexible EPDM rubber extrusion that goes between glass and metal sash lift channel. Available by the foot.
Luggage Rack Pads
p/n: 70-3459-87
This Luggage Rack Pad set is designed from the original part for superior fitment and seal. A five (5) piece set for Station Wagon models with an OEM factory luggage rack.
M6-1.0 Anchor Set - GM Vehicles
p/n: 70-4867-46
A top-quality neoprene rubber Well Nut, Washer and Screw Anchor for GM vehicle models. Well nut has a metric M6-1.0 captive brass nut. Overall length is 21/32". Replaces GM factory number #20130258.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Multi-Purpose Clips
p/n: 70-4802-45
A ten (10) piece set of Multi-Purpose Clips. Commonly used to retain Hood to Cowl Weatherstrips or Inner Fender Splash Panels.
Outer Beltline Scraper Weatherstrips
p/n: 50-0455-61
This Outer Beltline Scraper Weatherstrip pair is fully molded with EPDM rubber over a corrosion resistant brass metal core. These window scrapers are for models with the chrome strip on the door.
Outer Beltline Weatherstrip
p/n: 50-0496-61
This Outer Beltline Weatherstrip is fully molded with EPDM rubber over a corrosion resistant brass metal core. These window scrapers are for models with the chrome strip on the door. Designed like original with attaching tabs.
Outer Beltline Weatherstrip
p/n: 50-0497-61
This Outer Beltline Weatherstrip is fully molded with EPDM rubber over a corrosion resistant brass metal core. These window scrapers are for models with the chrome strip on the door. Designed like original with attaching tabs.
Outer Beltline Weatherstrip
p/n: 50-0466-61
This Outer Beltline Weatherstrip is fully molded with EPDM rubber over a corrosion resistant brass metal core. These window scrapers are for models with the chrome strip on the door.
Outer Beltline Weatherstrip
p/n: 50-0465-61
This Outer Beltline Weatherstrip is fully molded with EPDM rubber over a corrosion resistant brass metal core. These window scrapers are for models with the chrome strip on the door. Designed like original with attaching tabs.
Outer Beltline Weatherstrip
p/n: 70-0802-61
This Outer Beltline Weatherstrip is fully molded with EPDM rubber over a corrosion resistant brass metal core. These window scrapers are for models with the chrome strip on the door. Designed like original with attaching tabs.
Outer Beltline Weatherstrip
p/n: 70-0829-61
This Outer Beltline Weatherstrip is fully molded with EPDM rubber over a corrosion resistant brass metal core. These window scrapers are for models with the chrome strip on the door. Designed like original with attaching tabs.
Outer Beltline Weatherstrip
p/n: 70-0879-61
This Outer Beltline Weatherstrip is fully molded with EPDM rubber over a corrosion resistant brass metal core. These window scrapers are for models with the chrome strip on the door. Designed like original with attaching tabs.
Outer Beltline Weatherstrip
p/n: 70-0803-61
This Outer Beltline Weatherstrip is fully molded with EPDM rubber over a corrosion resistant brass metal core. These window scrapers are for models with the chrome strip on the door. Designed like original with attaching tabs.
Outer Beltline Weatherstrip
p/n: 50-0548-61
This Outer Beltline Weatherstrip is fully molded with EPDM rubber over a corrosion resistant brass metal core. These window scrapers are for models with the chrome strip on the door. Designed like original with attaching tabs.
Outer Beltline Weatherstrip
p/n: 50-0376-61
This Outer Beltline Weatherstrip is fully molded with EPDM rubber over a corrosion resistant brass metal core. These window scrapers are for models with the chrome strip on the door.
Outer Beltline Weatherstrip
p/n: 50-0549-61
This Outer Beltline Weatherstrip is fully molded with EPDM rubber over a corrosion resistant brass metal core. These window scrapers are for models with the chrome strip on the door. Designed like original with attaching tabs.
Outer Beltline Weatherstrip
p/n: 70-0830-61
This Outer Beltline Weatherstrip is fully molded with EPDM rubber over a corrosion resistant brass metal core. These window scrapers are for models with the chrome strip on the door. Designed like original with attaching tabs.
Outer Beltline Weatherstrip
p/n: 50-0488-61
This Outer Beltline Weatherstrip is fully molded with EPDM rubber over a corrosion resistant brass metal core. These window scrapers are for models with the chrome strip on the door. Designed like original with attaching tabs.
Outer Beltline Weatherstrip
p/n: 50-0378-61
This Outer Beltline Weatherstrip is fully molded with EPDM rubber over a corrosion resistant brass metal core. These window scrapers are for models with the chrome strip on the door.
Outer Beltline Weatherstrip
p/n: 50-0377-61
This Outer Beltline Weatherstip is fully molded with EPDM rubber over a corrosion resistant brass metal core. These window scrapers are for models with the chrome strip on the door Does not have chrome strip on weatherstrip).
Outline Beltline Weatherstrip
p/n: 70-0860-61
This Outer Beltline Weatherstrip is fully molded with EPDM rubber over a corrosion resistant brass metal core. These window scrapers are for models with the chrome strip on the door. Designed like original with attaching tabs.
Parking Brake Pedal Pad
p/n: 25-0071-22
Pad, parking brake pedal.Length: 2.125 inches. Width: 2.0 inches.
Parking Light Grommet
p/n: 60-0452-17
Grommet, parking light wiring harness through fender.Length: 3.25 inches.
Parking Light Lens Gasket
p/n: 25-0088-16
Gasket, parking light lens.Length: 6.625 inches. Width: 1.625 inches.
Parking/Backup Light Lens Gasket
p/n: 70-1272-16
Gasket, parking light lens and backup light lens. Die cut from one eighth (1/8) inch rubber.
Peel-N-Stick Door Edge Weatherstrip
p/n: 70-0390-WT
This Peel-N-Stick Door Edge Weatherstrip is designed for a specific set of vehicles but with its generic shape, has many uses outside of its original purpose. Available by the foot. Available by the foot.
Peel-N-Stick Door Weatherstrip
p/n: 70-0331-WT
This Peel-N-Stick Door Weatherstrip is made from high-quality EPDM sponge rubber. Available by the foot.
Peel-N-Stick Door Weatherstrip
p/n: 70-0145-WT
This Peel-N-Stick Door Weatherstrip is made from a high-quality EPDM sponge rubber. Available by the foot.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0773-WT
This Peel-N-Stick Trunk Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk directly to the body.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0774-WT
This Peel-N-Stick Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0510-WT
This Peel-N-Stick Trunk Weatherstrip is made from a high-quality EPDM sponge rubber. Available by the foot.
Plastic Guide Plate
p/n: 50-0385-58
Plastic guide plate, attaches to various outer scraper weatherstrips.Length: 1.625 inches. Width: .625 inches.
Power Top Cylinder Spacer
p/n: 70-0822-67
This Power Top Cylinder Spacer is used as the folding top power cylinder support. Molded from 100% EPDM dense rubber for durability. Four (4) spacers used per car.
Pressure Ring
p/n: 70-0261-69
Pressure ring (washer), sponge rubber, interior door handle and window regulator escutcheon. One and three fourths (1-3/4) inches outside diameter by three eighths (3/8) inch thick.
Prop Shaft Support
p/n: 25-0043-25
Insulator, drive shaft support, center, molded rubber on heavy steel core. Note: Not used on models with Air Ride suspension.
Quarter Window Bumper
p/n: 70-1583-62
Bumper, quarter window stop on sash channel.Length: .8125 inches. Width: .75 inches. Height: .50 inches.
Quarter window filler
p/n: 70-2048-67
Filler, quarter window weatherstrip, rear on inner panel. Hard to see part found at bottom of rear side window. Fully molded with metal core.Width: 2.
Quarter window filler
p/n: 70-2518-67
Filler, quarter window weatherstrip, rear on inner panel. Fully molded with metal core.
Quarter window filler
p/n: 70-3433-67
Weatherstrip, quarter window filler on rear inner panel. Original appearance, constructed with a brass core for longevity. Pair includes filler for both sides of vehicle.
Quarter Window Lock Pillar Fillers
p/n: 60-0602-79
This Quarter Window Lock Pillar Filler pair seals the bottom of the rear side window, and may also be known as a u-jamb or door jamb seal. Fully molded authentic rubber construction with brass metal core.
Quarter Window U Jamb Door Lock Pillar Fillers
p/n: 70-0982-79
This Quarter Window U Jamb Door Lock Pillar Filler pair seals the bottom of the rear side window. May also be known as a door jamb seal.
Quarter Window U Jamb Lock Pillar Fillers
p/n: 70-1532-79
This Quarter Window U Jamb Door Lock Pillar Filler pair is designed from the original part for superior fitment and sealing. This right and left weatherstrip filler mounts at the bottom of the rear side window, lower leading edge to seal the rear quarter window. Also known as a Door U Jamb Seal.
Quarter Window Vertical Leading Edge
p/n: 70-0141-58
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
Quarter window weatherstrip
p/n: 50-0282-77
Weatherstrip, fixed rear quarter window. Each vulcanized in one piece for ease of installation.
Quarter window weatherstrip
p/n: 60-0453-77
Channel, rear door stationary quarter window, right and left. Molded with all the original features.
Quarter window weatherstrip
p/n: 70-3278-77
Weatherstrip, rear stationary side window. Fully molded with proper joints and cross section.
Quarter window weatherstrip
p/n: 70-2030-77
Weatherstrip, rear quarter stationary vent window. This gasket is for the triangular window just behind the rear door.
Quarter Window Weatherstrip
p/n: 50-0557-77
Weatherstrip, fixed quarter window. Used on four (4) door sedans with reveal molding on doors.Width: 10.125 inches. Height: 14.25 inches.
Quarter Window Weatherstrip
p/n: 60-0281-77
This fixed rear quarter window channel is sold as a pair for the left and right. The seals are fully vulcanized for installation ease and a precise, factory fit.
Quarter window weatherstrip
p/n: 70-2125-77
Weatherstrip, rear quarter stationary vent window. This gasket is for the triangular window just behind the rear door on four (4) door post sedans.
Quarter Window Weatherstrip
p/n: 60-0446-77
Weatherstrip, stationary quarter windows. Eight (8) foot strip for two (2) quarter windows. Most models with stationary windows.Length: 96.0 inches.
Quarter Window Weatherstrips
p/n: 27-0040-77
This Quarter Window Weatherstrips pair is designed from the original part for superior fitment and seal. This seal mounts around the full perimeter of the quarter glass for a precise, factory fit. For fixed, stationary windows only.
Radiator Bracket Cushion
p/n: 70-2014-31
Radiator support bracket, insulator, upper. Two (2) used per car.Length: 6.0 inches.
Radiator Core Support Fillers
p/n: 70-4918-31
This two (2) piece Radiator Core Support Filler set is designed from the original part for superior fitment and function. Filler pieces are die cut from quality 3/32" masticated rubber to authentic original dimensions.
Radiator Lower Filler
p/n: 70-3314-45
This two (2) piece Radiator Lower Filler pair is designed from the original part for superior fitment and function. Filler pieces are die cut from quality masticated rubber to authentic original dimensions.
Radiator Mounting Insulator Pads
p/n: 70-2238-31
A four (4) piece set of Radiator Mounting Insulator Pads. For use on all four corners of the radiator. For vehicle models with three (3) wide core radiators.
Radiator Mounting Pad
p/n: 25-0087-31
Insulator, radiator support. Two (2) to four (4) used per car.Length: 6.75 inches.
Radiator Mounting Pad
p/n: 70-0963-31
Radiator mounting pad, insulator. Up to four (4) used per car.Length: 6.0 inches.
Radiator Top Seal
p/n: 25-0085-42
Seal, upper radiator baffle.Length: 1.625 inches. Width: .0625 inches.
Radiator Upper Support Filler
p/n: 70-3313-45
This two (2) piece Radiator Upper Support Filler pair is designed from the original part for superior fitment and function. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Fits at radiator to radiator upper support.
Rear axle bushing
p/n: 25-0081-32
Insulators, rear axle housing, upper and lower. Four (4) piece set.
Rear Bumper Gravel Shield
p/n: 60-0173-30
This Rear Bumper Gravel Shield, also known as a rear bumper face bar-to-body seal, is made of high quality dense rubber. Fully molded rubber with all original features.
Rear Bumper Grommet
p/n: 70-0164-29
Grommets, rear bumper. (Some cars have this type, some have our #70-0144-29, sold separately. They are both interchangeable and original). Fully molded rubber.
Rear Bumper Step Pad Set
p/n: 70-3637-87
This rear bumper step pad set contains the left, center, and right side step pads in the tailgate opening. They are fully molded with brass cores and designed from originals with factory style tread. All three pieces have correctly placed screw holes and are ready to install.
Rear coil spring pad
p/n: 50-0359-35
Insulators, rear coil spring. Fabric reinforced rubber as original. One (1) pair per car.
Rear Door Hinge Pillar Filler
p/n: 70-2226-79
This Rear Door Hinge Pillar Filler seal pair is designed from the original part for superior fitment and sealing. This part seals the bottom of the rear side window, and may also be known as a door u-jamb seal. Fully molded authentic rubber construction with brass metal core.
Rear Door Hinge Pillar Fillers
p/n: 60-0591-79
This Rear Door Hinge Pillar Filler pair seals the bottom of the rear door side window and may also be known as a rear door jamb seal. Fully molded authentic rubber construction with metal core.
Rear Door Lock Pillar Filler
p/n: 70-2808-79
This Rear Door Lock Pillar Filler pair is designed from the original part for superior fitment and sealing. This right and left weatherstrip filler mounts at the bottom of the rear side window, lower leading edge to seal the rear quarter window. Also known as a door jamb seal.
Rear Door Lock Pillar Fillers
p/n: 70-1816-79
This Rear Door Lock Pillar Filler pair is designed from the original part for superior fitment and sealing. This right and left weatherstrip filler mounts at the bottom of the rear side window, lower leading edge to seal the rear door window. Fully molded authentic rubber construction.
Rear Door Lock Pillar Weatherstrips
p/n: 70-1907-79
This Rear Door Lock Pillar Weatherstrip pair seals the bottom of the rear side window, and may also be known as a door jamb seal. Fully molded authentic rubber construction with metal core. For rear doors.
Rear Door Lower Hinge Pillar Weatherstrips
p/n: 70-0947-73
This Rear Door Lower Hinge Pillar Weatherstrip pair is designed from the original part for superior fitment and seal. This weatherstrip fits at the rear door lower hinge pillar. Length is sixteen (16") inches.
Rear Door Opening Step Pad Mats
p/n: 70-1119-45
This Rear Door Opening Step Pad Mat pair is designed from the original part for an authentic fit, finish, and appearance. Made using high quality rubber with metal backings as OEM original.
Rear Door Pillar Filler
p/n: 70-0837-79
This Rear Door Pillar Filler pair is designed from the original part for superior fitment and sealing. This left and right weatherstrip filler mounts at the bottom of the rear side window, lower leading edge to seal the rear quarter window. Also known as a door jamb seal.
Rear door vent weatherstrip
p/n: 38-0009-74
Weatherstrip, rear door vent. For Buick order our #70-0695-74 division post weatherstrip separately. For Cadillac order our #70-0695-74 division post seal separately. For Chevrolet, we do not have a matching metal core division post seal for this part, yo