Side Window Vertical Leading Edge Weatherstrips
p/n: 70-1820-80
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised.
Side Window Vertical Leading Edge Weatherstrips
p/n: 70-0926-80
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised.
Side Window Vertical Leading Edge Weatherstrips
p/n: 50-0344-80
This Side Window Vertical Leading Edge Weatherstrips pair is designed from the original part for superior fitment and seal. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised.
Side Window Vertical Leading Edge Weatherstrips
p/n: 70-0882-80
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised.
Sliding Quarter Window Seal
p/n: 70-2162-78
Weatherstrip, sliding quarter window. Vertically mounted in body where leading edge of sliding quarter window fits when closed.Length: 13.75 inches.
Sliding Quarter Window Seal
p/n: 60-0398-78
Weatherstrip, sliding quarter window. Mounted vertically in body where leading edge of sliding window fits when closed. Right & left rubber only.
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft. lengths.
Solenoid Plunger Boot
p/n: 60-0567-21
Boot, solenoid plunger, starter switch at starter.Height: 1.625 inches.
Spark plug grommet
p/n: 70-1180-21
Grommet, spark plug & coil wire at distributor cap outlets. For nine (9mm) millimeter wire, earlier years.
Spark plug grommet
p/n: 70-1181-21
Grommet, spark plug and coil wire at distributor cap outlets. For seven (7mm) millimeter, later years.
Splash Apron / A-Arm Dust Shield
p/n: 70-3232-45
This two (2) piece Splash Apron / A-Arm Dust Shield pair is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Splash Apron / A-Arm Dust Shield
p/n: 70-3066-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Splash Apron / A-Arm Dust Shield
p/n: 70-3065-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Splash Apron / A-Arm Dust Shield
p/n: 70-3067-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Splash Apron / A-Arm Dust Shield
p/n: 70-3064-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Splash Apron / A-Arm Dust Shield Filler
p/n: 70-2799-45
This Splash Apron / A-Arm Dust Shield Filler pair is designed from the original part for superior fitment and seal. Filler pair pieces are die cut from quality masticated rubber to authentic original dimensions. Left and Right pieces fit over suspension a-arms and inside front inner fenders.
Splash Apron / A-Arm Dust Shield Fillers
p/n: 70-3483-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler pair is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Left and Right pieces fit over suspension a-arms and inside front inner fenders.
Stabilizer Bar Bushings
p/n: 70-4678-34
This Stabilizer Bar to Frame Bushing pair may fit either front or rear stabilizer / sway bars depending on the vehicle. Manufactured with quality materials to original specifications.
Stabilizer Bar End Link Set
p/n: 70-0567-34
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt. 5/16"-24NF x 7-5/8" long. Includes metal sleeves, cup washers and rubber grommets.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Standard rubber washer
p/n: 60-0726-45
Washer, for attaching moldings, emblems, and fender guards as required on body.
Starter Pedal Pad
p/n: 25-0049-89
Pad, starter pedal. Original pattern, brown rubber, exact copy.Height: .50 inches.
Stationary Quarter Window Gasket
p/n: 60-0424-77
This Stationary Quarter Window Gasket pair is designed from the original part for an authentic fit, finish, and appearance. This fixed rear quarter window channel is vulcanized in one piece with correct sharp corner. No splicing required.
Steering Column Gasket - Automatic Transmission
p/n: 70-4467-36
This Steering Column gasket is designed from the original part for superior fitment and sealing. Gasket is machine cut from quality sponge rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan.
Steering Knuckle Support Seal
p/n: 50-0199-35
Seal, steering knuckle support, upper pivot pin. Four (4) required per car.Height: .5 inches.
Suspension Bumper - Front Lower Control Arm
p/n: 50-0092-32
This Suspension Bumper is designed from the original part for superior fitment and function. Bumper mounts to the front suspension lower control arm. Two (2) per car required.
Swing-Out Quarter Window Weatherstrips
p/n: 70-4124-76
This Swing-Out Quarter Window Weatherstrip pair is not a reproduction of an OEM part, but rather an expertly engineered solution specific for this application. Guaranteed performance and "factory-like" look.
Tailgate bumper
p/n: 70-2854-87
Bumper, tailgate support. Two (2) bumpers mount on tailgate and two (2) mount on body in lower sections. Four (4) required.
Tailgate Bumper - Upper and Lower
p/n: 70-1827-87
This upper / lower Tailgate Bumper is designed from the original part for superior fitment and seal. Fully molded with top quality EPDM rubber over corrosion resistant brass cores to ensure durability and function.
Tailgate Latch Striker Bumper
p/n: 70-1911-87
This Tailgate Latch Striker Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the station wagon tailgate to cushion its closure. Usually requires two (2) bumpers each per vehicle.
Tailgate Lower Weatherstrip
p/n: 70-2123-85
This Tailgate Lower Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts to the sides and bottom of the tailgate with properly spaced plastic clips.
Tailgate Outer Window Felt Weatherstrip
p/n: 80-0011-57
This reproduction Original material Tailgate Glass Outer Window Felt Weatherstrip is designed from the original part for superior fitment and seal. This flat chrome bead outer window felt wipes the outside tailgate window glass when the glass is lowered.
Tailgate Weatherstrip
p/n: 82-0181-84
This tailgate weatherstrip is designed from the original part for superior fitment and seal. The seal mounts to the sides and bottom of the tailgate opening directly to the body. Includes molded ends.
Tailgate Weatherstrip
p/n: 70-1519-87
Weatherstrip, tailgate opening. Pinchweld finish on body. This tailgate weatherstrip reproduction is designed from the original part for superior fitment and seal.
Tailgate Weatherstrip
p/n: 70-3424-84
This Tailgate Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts to the sides and bottom of the tailgate with properly spaced plastic clips. Includes molded ends.
Tailgate wedge
p/n: 70-2855-87
Wedge, tailgate bumper anti-rattler. Mounts on both end jamb areas on tailgate.
Tailgate Window Felt Beltline Weatherstrips
p/n: 80-0804-57
This Tailgate Glass Window Felt Beltline Weatherstrip reproduction pair is designed from the original part for superior fitment and seal. This window felt molding mounts to the tailgate with the included fasteners.
Tailgate Window Felt Outer Beltline Weatherstrip
p/n: 80-0793-57
This Tailgate Glass Outer Only Window Felt Beltline Weatherstrip reproduction is designed from the original part for superior fitment and seal. This window felt molding mounts to the tailgate with tabs. These window felts wipe the tailgate window glass when the glass is lowered.
Taillight Gasket
p/n: 25-0078-15
Gasket, taillight housing to body. Note: Two (2) pairs are required for Starfires. All other vehicles need one (1) pair.
Taillight Lens Gasket
p/n: 25-0079-15
Gasket, taillight lens to housing. Shear die cut sponge rubber.Length: 10.0 inches.
Taillight Lens Gasket
p/n: 25-0100-15
Gasket set, taillight housing and lens. Eight (8) piece set used on taillight and backup light.
Taillight Mounting Gaskets
p/n: 70-3793-15
This two (2) piece Taillight Mounting Gasket is die cut sponge rubber to authentic original dimensions.
Taillight Mounting Pad
p/n: 25-0053-15
Mounting Pad set, tail light to body and crown molding to rear fender, right and left. Sold as four (4) piece set only.
Torque Ball Boot
p/n: 25-0034-24
Cushion, propeller shaft (drive shaft) bearing.Height: 1.0625 inches.
Track Bar Bushing
p/n: 25-0080-32
Bushing, rear axle track bar. Made in halves for easier replacement. Sold in pairs, two (2) pair needed per bar.Height: .75 inches.
Transmission Filler Flaps
p/n: 70-3686-25
This Transmission Filler Flap pair is designed from the original part for superior fitment and seal. For Cutlass and 442 models with automatic transmission. Two (2) piece filler flap pair located where the frame meets the firewall on the right and left sides.