Engine Mount
p/n: 30-0292-11
This Engine Mount pair is used as the engine crank case link ball insulator. Correctly designed with careful attention to detail as original. Sold only in pairs.
Engine Mount Pad
p/n: 30-0331-11
This Engine Mount Pad pair is used as a support at the timing gear cover. One (1) pair required per car. Sold only in pairs.
Engine Mount Service – Revulcanization Only
p/n: 30-0543-11
This Revulcanization Service Only is designed to restore your Engine Mount Stabilizer Bracket to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Engine Mount Service – Revulcanization Only
p/n: 30-0185-11
This Revulcanization Service Only is designed to restore your Rear Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Fender Welting 1/4" Bead - 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty-five (25) foot roll. Typically used to attach two (2) fenders to body.
Fender Welting 1/4" Bead - 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body.
Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Fender Welting with 3/16" Bead - 50ft
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Front Bumper Grommet
p/n: 30-0171-28
Grommets, front bumper. Molded right and left with correct detail as originally found. Fully molded rubber.
Front Door Vent Window Set
p/n: 90-0327-90
This six (6) piece Front Door Vent Window Set contains the upper and lower seals that cover the top, front, and bottom of the vent window as well as the division post seals.
Front Door Vent Window Weatherstrip Set
p/n: 30-0103-55
This four (4) piece Front Door Vent Window Weatherstrip Set contains the upper and lower seals that cover the top, front, and bottom of the vent window. All of the pieces are designed from original parts for a precise, factory fit.
Front Fender Seal
p/n: 30-0189-44
Liners, front fender to running board. Reversible right and left like original. Length: 15.0 inches.
Front spring bushing
p/n: 30-0393-32
Bushing assembly, front wheel support; upper and outer. Inlox type cartridge bushing assembly.
Front Suspension Bumper
p/n: 30-0490-32
Bumper, front suspension (inside of coil spring). Made with three five sixteenths (5/16) inch studs as original.
Front suspension bushing
p/n: 30-0239-32
Bushings, front suspension torque arm. Necessary for proper front end geometry.
Fuel Tank Support Pad
p/n: 30-0482-41
This Fuel Tank Support Pad is made of a high quality EPDM dense rubber. This cushion is used to help reduce noise. Available by the foot.
Gearshift Seal
p/n: 30-0165-24
Seal, gearshift to floorboard.Length: 5.625 inches. Width: 4.875 inches.
Headlight Lens Gasket
p/n: 30-0176-14
Gaskets, headlight lens and reflector mounting. A three sixteenths (3/16) inch cross section rubber ring of proper diameter.