Side Window Vertical Leading Edge Weatherstrips
p/n: 50-0344-80
This Side Window Vertical Leading Edge Weatherstrips pair is designed from the original part for superior fitment and seal. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised.
Side Window Weatherstrip
p/n: 70-3868-77
This Side Window Weatherstrip set contains the left and right seals for the two (2) fixed windows on the side of the vehicle. The seals have properly molded corners for a precise, factory fit.
Sliding Quarter Window Seal
p/n: 70-2162-78
Weatherstrip, sliding quarter window. Vertically mounted in body where leading edge of sliding quarter window fits when closed.Length: 13.75 inches.
Sliding Quarter Window Seal
p/n: 60-0398-78
Weatherstrip, sliding quarter window. Mounted vertically in body where leading edge of sliding window fits when closed. Right & left rubber only.
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft. lengths.
Solenoid Plunger Boot
p/n: 60-0567-21
Boot, solenoid plunger, starter switch at starter.Height: 1.625 inches.
Spark plug grommet
p/n: 70-1180-21
Grommet, spark plug & coil wire at distributor cap outlets. For nine (9mm) millimeter wire, earlier years.
Spark plug grommet
p/n: 70-1181-21
Grommet, spark plug and coil wire at distributor cap outlets. For seven (7mm) millimeter, later years.
Splash Apron / A-Arm Dust Shield
p/n: 70-3316-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Splash Apron / A-Arm Dust Shield Filler
p/n: 70-3484-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler pair is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Left and Right pieces fit over suspension a-arms and inside front inner fenders.
Splash Apron / A-Arm Dust Shield Filler
p/n: 70-3068-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler pair is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Left and Right pieces fit over suspension a-arms and inside front inner fenders.
Splash Apron / A-Arm Dust Shield Filler
p/n: 70-3069-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler pair is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Left and Right pieces fit over suspension a-arms and inside front inner fenders.
Splash Apron / A-Arm Dust Shield Filler Set
p/n: 70-3309-45
This five (5) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and function. Filler pieces are die cut from quality masticated rubber to authentic original dimensions.
Splash Apron / A-Arm Dust Shield Filler Set
p/n: 70-3332-45
This five (5) piece Splash Apron / A-Arm Dust Shield Filler Set is designed from the original part for superior fitment and function. Filler pieces are die cut from quality masticated rubber to authentic original dimensions.
Splash Apron / A-Arm Dust Shield Fillers
p/n: 70-3483-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler pair is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Left and Right pieces fit over suspension a-arms and inside front inner fenders.
Spring shackle seal
p/n: 70-1125-33
Washer, front and rear spring shackle, seal for shackle pin. Constructed of neoprene.
Stabilizer Bar Bushings
p/n: 70-4678-34
This Stabilizer Bar to Frame Bushing pair may fit either front or rear stabilizer / sway bars depending on the vehicle. Manufactured with quality materials to original specifications.
Stabilizer Bar End Link Set
p/n: 70-0567-34
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt. 5/16"-24NF x 7-5/8" long. Includes metal sleeves, cup washers and rubber grommets.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Stabilizer Bushing
p/n: 27-0085-34
Bushings, for stabilizer bracket. Fully molded rubber. Correct dimensions, not an aftermarket replacement.
Starter Button
p/n: 27-0048-21
Button, starter pedal rod. All rubber, made to work directly onto pedal rod three eighths (3/8) inch hole.
Starter Pedal Pad
p/n: 25-0049-89
Pad, starter pedal. Original pattern, brown rubber, exact copy.Height: .50 inches.
Stationary Quarter Window Gasket
p/n: 60-0424-77
This Stationary Quarter Window Gasket pair is designed from the original part for an authentic fit, finish, and appearance. This fixed rear quarter window channel is vulcanized in one piece with correct sharp corner. No splicing required.
Steering Column - Floor Seal
p/n: 70-3358-36
This Steering Column is designed from the original part for superior fitment and sealing. Seal part is die cut from quality masticated rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan inside the vehicle.
Steering Column Gasket - Automatic Transmission
p/n: 70-4467-36
This Steering Column gasket is designed from the original part for superior fitment and sealing. Gasket is machine cut from quality sponge rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan.
Steering Knuckle Support Seal
p/n: 50-0199-35
Seal, steering knuckle support, upper pivot pin. Four (4) required per car.Height: .5 inches.
Suspension Bumper - Front Lower Control Arm
p/n: 50-0092-32
This Suspension Bumper is designed from the original part for superior fitment and function. Bumper mounts to the front suspension lower control arm. Two (2) per car required.
Swing-Out Quarter Window Weatherstrips
p/n: 70-4124-76
This Swing-Out Quarter Window Weatherstrip pair is not a reproduction of an OEM part, but rather an expertly engineered solution specific for this application. Guaranteed performance and "factory-like" look.
Tailgate Bumper - Upper and Lower
p/n: 70-1827-87
This upper / lower Tailgate Bumper is designed from the original part for superior fitment and seal. Fully molded with top quality EPDM rubber over corrosion resistant brass cores to ensure durability and function.
Tailgate Latch Striker Bumper
p/n: 70-1911-87
This Tailgate Latch Striker Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the station wagon tailgate to cushion its closure. Usually requires two (2) bumpers each per vehicle.
Tailgate Lower Weatherstrip
p/n: 70-2123-85
This Tailgate Lower Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts to the sides and bottom of the tailgate with properly spaced plastic clips.
Tailgate or Back Door Weatherstrip
p/n: 70-3604-84
This Tailgate or Back Door Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts with properly spaced plastic clips around the full perimeter of the rear opening.
Tailgate Outer Window Felt Weatherstrip
p/n: 80-0011-57
This reproduction Original material Tailgate Glass Outer Window Felt Weatherstrip is designed from the original part for superior fitment and seal. This flat chrome bead outer window felt wipes the outside tailgate window glass when the glass is lowered.
Tailgate run channel filler
p/n: 70-3302-87
Tailgate glass run channel, upper molded section, left and right. Molded piece with metal core ready to attach to tailgate window run channel.
Tailgate Weatherstrip
p/n: 70-2091-85
This Tailgate Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts to the sides and bottom of the tailgate with properly spaced plastic clips. Includes molded ends.
Tailgate Weatherstrip
p/n: 70-3299-85
These tailgate weatherstrips are designed from the original part for superior fitment and seal. The seals mount to the sides and bottom of the tailgate opening directly to the body. Includes molded ends.
Tailgate Weatherstrip
p/n: 82-0181-84
This tailgate weatherstrip is designed from the original part for superior fitment and seal. The seal mounts to the sides and bottom of the tailgate opening directly to the body. Includes molded ends.
Tailgate Weatherstrip
p/n: 70-1909-85
This Tailgate Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts to the sides and bottom of the tailgate with properly spaced plastic clips. Includes molded ends that contain brass cores.
Tailgate Weatherstrip
p/n: 70-3424-84
This Tailgate Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts to the sides and bottom of the tailgate with properly spaced plastic clips. Includes molded ends.
Tailgate Weatherstrip
p/n: 70-1519-87
Weatherstrip, tailgate opening. Pinchweld finish on body. This tailgate weatherstrip reproduction is designed from the original part for superior fitment and seal.
Tailgate Window Felt Beltline Weatherstrips
p/n: 80-0804-57
This Tailgate Glass Window Felt Beltline Weatherstrip reproduction pair is designed from the original part for superior fitment and seal. This window felt molding mounts to the tailgate with the included fasteners.
Taillight Gasket
p/n: 60-0671-15
Gasket, taillight to fender. Two 1/4" strips of sponge rubber cut 26-3/4" long. One (1) pair required per car.
Taillight Gasket Kit
p/n: 70-3566-15
Kit, taillight lens and mounting gaskets. Ten (10) piece set. Includes 1 pair of #70-3565-15 lens to tail light body mounting seals and eight (8) each of 70-3564-15 tail light assembly to body seals.
Taillight Gasket Set
p/n: 70-2243-15
A (6) piece Taillight Gasket Set designed to cushion and protect housing and body sheet metal.
Taillight Lens Gasket
p/n: 70-3565-15
Gasket, taillight lens mounting gasket. Machine die cut from 1/4" thick sponge rubber. Seals tail light lens to tail light assembly. Included in our kit #70-3566-15.
Taillight Lens Gaskets
p/n: 70-3556-15
This Taillight Lens Gasket includes left and right sides. Mounts between the tail-light-lens and the lens-retaining-body for a perfect fit. Made of fully molded soft-dense rubber compound to ensure proper installation and performance.
Taillight Mounting Pad
p/n: 27-0069-15
Pad, taillight mounting pad to body. Fully molded with original details. Length: 6.375 inches.
Taillight Mounting Pad
p/n: 27-0062-15
Pad, taillight to body mounting. Right and left molded as original with proper bead lip. Length: 4.50 inches.
Taillight Mounting Pad
p/n: 27-0068-15
Pad, taillight and license bracket mounting. Not listed in Master Parts Books, but we have seen this part on several original cars.
Taillight Mounting Pad
p/n: 70-2166-15
Pad, taillight mounting to rear quarter panel. Proper extrusion cross section like original. Two (2) strips twenty-four (24) inch long. Length: 24.0 inches.
Taillight Mounting Pad
p/n: 70-3564-15
Gasket, taillight mounting pad. Eight (8) used per car. Machine die cut 5/8" thick sponge rubber seals tail light assembly to body. Included in our kit part number #70-3566-15.
Taillight Mounting Pad
p/n: 27-0025-15
Pad, taillight mounting, right and left.Length: 5.9375 inches.
Traction Bar Bumper
p/n: 70-2293-35
This Traction Bar Bumper is designed from the original part for superior fitment and function. An excellent reproduction of part found on models with radius rod traction bars.
Transmission Mount
p/n: 70-2058-25
This Transmission Mount is a new aftermarket replacement mount manufactured to meet or exceed factory specifications.. One (1) required per vehicle.
Trunk - Decklid Bumper
p/n: 70-3528-87
This Trunk-Decklid Bumper is a quality reproduction of the original factory part. This adjustable rubber bumper attaches to the vehicle body to support / cushion the trunk lid closure.
Trunk Bumper
p/n: 50-0163-87
Bumper, trunk. Brass core, screw held. Two (2) per car.Length: 1.5 inches. Width: .75 inches.
Trunk Bumper
p/n: 34-0399-87
Bumper, trunk opening on lid. Metal core, as original, screw held. Two (2) required per car.
Trunk Bumper
p/n: 70-0296-87
T-nut, trunk bumper in gutter at sides, brass core tapped 10-32 thread. Two (2) required per car. For models having partial weatherstrip in gutter of body.
Trunk Bumper
p/n: 50-0546-87
Bumper, trunk. On side near hinge end. Made with metal core.Width: 1.625 inches. Height: 1.0 inches.
Trunk Deck Lid Rubber Bumpers
p/n: 70-2601-42
This Trunk Deck Lid Rubber Bumper pair is designed from the original part for superior fitment, finish and function. The correct OE style trunk deck lid rubber bumpers stoppers. Two required per car.
Trunk Handle Grommet
p/n: 50-0183-87
Grommet, trunk handle bezel-thru-trunk lid. Special size, one (1) inch inside diameter.Buick 1937 Grommet, trunk handle bezel-thru-trunk lid.
Trunk Hinge Mounting Pad
p/n: 70-1231-87
Mounting pads, trunk hinge. Four (4) piece set.Length: 8.8125 inches.
Trunk Or Hatchback Weatherstrip
p/n: 82-0038-84
This Trunk Or Hatchback Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk or hatchback opening directly to the body.
Trunk or Hood Bumper
p/n: 34-0203-42
This Bumper is designed to be used for the trunk or hood. The bumper is molded with clearance for the screw.