Fender Washer - Rubber
p/n: 20-2191-44
This quality rubber Fender Washer is designed from the original part for superior fitment and function. For the mounting of the rear fender. Large type, one and one half (1-1/2") inches diameter.
Fender Washer - Rubber
p/n: 20-2190-44
This quality rubber Fender Washer is designed from the original part for superior fitment and function. For the mounting of the front fender. Small type. One and one fourth (1-1/4") inches diameter.
Standard rubber washer
p/n: 60-0726-45
Washer, for attaching moldings, emblems, and fender guards as required on body.
Front Fender To Body Pillar Pad
p/n: 20-2764-45
This Front Fender To Body Pillar Pad is designed from the original part for superior fitment and function. Two (2) required per car, this pad fits between the front fender and A-pillar.
Hood Bumper
p/n: 20-2753-42
This Hood Bumper is a quality reproduction of the original factory part. The bumper attaches to the front fenders to support/cushion the hood closure. Used to provide a cushion for the hood closure that also minimizes vibration.
Hood and Fender Bumper
p/n: 70-3446-42
This Hood / Fender Bumper is a quality reproduction of the original factory part. This adjustable rubber bumper attaches to the front fender to support / cushion the hood closure.
Hood to Fender Bumper
p/n: 82-0022-42
This single molded Hood to Fender Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the front fender to support / cushion the hood closure. Usually requires four (4) bumpers each per vehicle.
Bumper support bar pad
p/n: 20-2765-45
Pads, front bumper bracket to fender. Two (2) required per car.
Hood to Fender Bumper
p/n: 70-3305-42
This Hood to Fender Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure. Four (4) required per car.
11/16" Hood Bumper
p/n: 33-0003-42
Bumper, hood, 2 uses. Hood to radiator shell at side panel, hood to fender, as required.
Hood Bumper
p/n: 33-0861-42
This Hood Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
1-3/8" Wiring Grommet
p/n: 32-0369-20
This Wiring Grommet is fully molded and designed from the original part for superior fitment and seal. Designed to run the wiring harness through the fender skirts or hood latch lower mounting panels.
3/8" Inner Fender Bumper
p/n: 33-0512-44
Inner fender to inner splash pan bumper. This bumper is not a generic replacement, and will only be seen when inner fender is removed.
1/2" Hood Bumper
p/n: 33-0031-42
Self-retaining hood bumper, along edge of hood against fender. Up to twenty (20) per car.
Hood To Fender Bumper
p/n: 70-1836-42
This Hood To Fender Bumper is designed from the original part for superior fitment, finish and function. This bumper is manufactured with quality EPDM dense rubber and measures 1-7/16" x 11/16" inches.
15/16" Firewall Grommet
p/n: 32-0066-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. Designed for firewall applications such as running the headlight wire through the fender.
Fender Flare Edge Trim
p/n: 70-4080-120
This Fender Flare Edge Trim mounts between the fender flare and the body to protect your vehicle by minimizing contact, vibrations and gaps. Available by the foot.
3/4" Trunk Floor Pan Plug
p/n: 35-0070-87
This Trunk Floor Pan Plug is fully molded and designed from the original part for superior fitment and seal. This plug is made from high-quality EPDM dense rubber to provide excellent durability.
Fender Flare Edge Trim
p/n: 70-4080-99
This Fender Flare Edge Trim mounts between the fender flare and the body to protect your vehicle by minimizing contact, vibrations and gaps. Available by the foot.
Peel-N-Stick Body / Fender Weatherstrip
p/n: 70-3973-445
A Peel-N-Stick Body / Fender Weatherstrip made from high-quality EPDM dense rubber. This weatherstrip is designed to fill the gaps between body panels and fender flares. Available by the foot.
Hood bumper
p/n: 70-3377-42
Bumper, hood-to-fender. Slides into slot on fender flange. Four (4) required per car.
Front Fender Plugs
p/n: 20-0753-20
This Front Fender Plug pair is a reproduction manufactured to OEM specifications to install for an authentic fit and finish. Used on the top of the front fender towards the rear to help reduce heat and fumes from entering the cab.
Hood to Fender Bumper
p/n: 70-1638-42
This Hood to Fender Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure. Two (2) required per car.
Hood to Fender Bumper
p/n: 70-1962-42
This Hood to Fender Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure. Four (4) required per car.
Hood Bumper
p/n: 70-1962-108
Steele Rubber Products has the best quality stem bumpers for your Street Rod or Custom Build project. Excellent for use in many applications.
Front fender center pad
p/n: 20-1865-45
Pads, back center of front fender. Mounts where fender bolts to cowl.
Wiper Hose Grommet
p/n: 20-2206-53
This Wiper Hose Grommet is used where the wiper hose and temperature gauge wire go through the firewall. The grommet can also be used where the headlight bucket wires go through the inner fender.
1-5/8" Access Hole Plug
p/n: 35-0517-45
This Access Hole Plug is fully molded and designed from the original part for superior fitment and seal. This plug is made from high-quality EPDM dense rubber to provide excellent durability. Designed for rocker panel end, under fender.
Hood to Fender Bumper
p/n: 70-1637-42
This Hood to Fender Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure. Two (2) required per car.
1-1/4" Headlight Cable Grommet
p/n: 32-0492-14
This Headlight Cable Grommet is fully molded and designed from the original part for superior fitment and seal. Designed for firewall applications such as running the headlight cable through the fender.
5/8" Hood Corner Pad
p/n: 33-0117-108
This Hood Corner Pad is molded from quality dense rubber to ensure durability. Designed for the hood, the generic shape makes this bumper usable for a variety of applications on your Street Rod or Custom Build project.
3/4" Hood Side to Fender Bumper
p/n: 33-0542-42
A quality Hood Side To Fender Bumper. Button type and self-retaining. Replaces factory #391463.
Tailgate Latch Striker Bumper
p/n: 70-1911-87
This Tailgate Latch Striker Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the station wagon tailgate to cushion its closure. Usually requires two (2) bumpers each per vehicle.
Trunk Bumper
p/n: 70-2607-87
This Trunk Bumper is quality reproduction of the original factory part. This rubber bumper attaches to the rear body to support / cushion the Trunk / Decklid closure. Usually requires two (2) bumpers each per vehicle.
1-1/2" Antenna Hole Plug
p/n: 35-0327-45
This Antenna Hole Plug is fully molded and designed from the original part for superior fitment and seal. Designed for antenna mounting for inner fender at shroud, vehicles without a fender-mounted antenna.
Hood Side Bumper
p/n: 20-0953-42
This Hood Side Bumper is a quality reproduction of the original factory part. This rubber bumper mounts on the front fender to support / cushion the hood closure. Usually requires two (2) bumpers each per vehicle.
Hood Bumper
p/n: 50-0468-42
Bumper, hood side to fender. Six (6) required per car.Width: 1.8125 inches. Height: 1.8125 inches.
Hood Bumper
p/n: 70-1607-42
This Hood Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to support / cushion the hood closure.
Hood to Fender Bumper
p/n: 70-4176-42
This Hood to Fender Bumper is a quality reproduction of the factory part. This rubber bumper attaches to the front fender to support or cushion the hood closure. Usually requires four (4) bumpers each per vehicle.
Taillight Gasket
p/n: 70-1051-15
Weatherstrip, taillight housing to fender.Length: 50.0 inches. Width: .3125 inches.
Trunk Bumper
p/n: 70-2612-87
This Trunk Bumper is quality reproduction of the original factory part. This rubber bumper attaches to the rear body to support / cushion the Trunk / Decklid closure. Usually requires two (2) bumpers each per vehicle.
Hood to Fender Bumper
p/n: 70-1630-42
This Hood to Fender Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure. Four (4) to six (6) required per vehicle.
Hood Bumper
p/n: 70-0991-42
Bumper, hood to fender ledge. Typically four (4) to six (6) used per car.Length: 1.15625 inches. Width: .3125 inches.
Headlight Seal
p/n: 27-0090-119
Steele Rubber Products has the best quality headlight seals for your Street Rod or Custom Build project.These headlight seals are made of top-quality EPDM rubber with a high level of fit and finish for the Builder’s creative application and use.
1" Body/Fender Seal
p/n: 50-0528-457
EPDM dense rubber seal designed to fill the gap between body and fenderettes. Available by the foot.
Hood to Fender Bumper
p/n: 70-1639-42
This Hood to Fender Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure. Two (2) required per car.
Hood To Fender Bumper
p/n: 70-2609-42
This Hood To Fender Bumper is a quality reproduction of the original factory part. Original extruded style cut to proper width.
Front Fender Pads
p/n: 20-1866-45
This Front Fender Pad pair is designed from the original part for superior fitment and seal. These weatherstrip pads fit at the top rear of the front fender to cowl panel.
1/4" Headlight seal
p/n: 27-0090-14
Seal, headlight bezel to fender. Replaces factory #5948942, 5949836. Available by the foot.
Hood to Fender Bumper
p/n: 40-0503-42
Bumper, hood to fender ledge. Correct original cross-section. Up to ten (10) required per car.
Hood To Fender Bumper
p/n: 70-3397-42
This Hood to Fender Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the front fender to support / cushion the hood closure. Usually requires six (6) bumpers each per vehicle.
Hood Bumper
p/n: 70-1608-42
This Hood Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Hood to Fender Bumper
p/n: 70-1963-42
This Hood to Fender Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Front Fender Dust Shield Clip
p/n: 70-0681-44
This Front Fender Dust Shield Clip is designed from spring tempered wire, to original configuration. Up to sixteen (16) per car required.
Hood Bumper
p/n: 70-1963-108
Steele Rubber Products has the best quality stem bumpers for your Street Rod or Custom Build project. Excellent for use in many applications.
Hood Bumper
p/n: 70-3397-108
Steele Rubber Products has the best quality stem bumpers for your Street Rod or Custom Build project. Excellent for use in many applications.
Fender Bumper
p/n: 33-0545-30
Bumper, fender extension to quarter panel. Fully molded rubber. One and one fourths inch (1-1/4") length by eleven sixteenths inch (11/16") base diameter.
Hood To Fender Bumpers
p/n: 70-4733-42
This Hood To Fender Bumper pair is a quality reproduction of the original factory part. These rubber bumpers attach to the front fenders to support / cushion the hood closure.
Hood Bumper
p/n: 50-0511-42
Bumper, hood to fender ledge. Correct detail, made from highest quality rubber.Width: .75 inches. Height: .875 inches.
Hood Bumper
p/n: 70-0866-42
This Hood Bumper is a quality reproduction of the original factory part. The hood bumpers provide a cushion for the hood closure that also minimizes vibration.
Inner Fender Seal
p/n: 60-0667-45
Seal, inner fender to frame. Extruded rubber strip replacement. Available by the foot.
Fender To Hood Side Cushion Bumper
p/n: 70-2610-42
This Fender To Hood Side Cushion Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the front fender to support / cushion the hood closure. Usually requires four (4) bumpers each per vehicle.
Brown Trunk Bumper
p/n: 30-0299-89
Cap for covering fender bolt, trunk interior. Brown rubber.Height: .8125 inches.
Inner Fender Filler
p/n: 60-0660-45
This Inner Fender Filler is designed from the original part for an authentic fit, finish, and appearance. Available by the foot.
Hood To Fender Bumper
p/n: 50-0473-42
This Hood to Fender Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the front fender to support / cushion the hood closure.
Antenna to Front Fender Mount Pad
p/n: 20-1809-19
This Antenna to Front Fender Mount Pad is a high-quality reproduction of the original factory part. This mount pad installs between the antenna mounting base and top of front fender to protect the painted surface.
Hood To Fender Bumpers
p/n: 70-4735-42
This Hood to Fender Bumper pair is a quality reproduction of the original factory part. These rubber bumpers attach to the front fenders to support / cushion the hood closure.
Taillight Gasket
p/n: 60-0671-15
Gasket, taillight to fender. Two 1/4" strips of sponge rubber cut 26-3/4" long. One (1) pair required per car.
Hood To Fender Bumpers
p/n: 70-4734-42
This Hood to Fender Bumper pair is a quality reproduction of the original factory part. These rubber bumpers attach to the front fenders to support / cushion the hood closure.
Front Fender or Quarter Panel Extensions
p/n: 20-2761-45
This Front Fender or Rear Quarter Panel Extension pair is designed from the original part for superior fitment and seal. The pair comes as one solid unit that is perforated for the customer to split apart and is easy to install.
Door Bumper
p/n: 34-0131-37
Bumper, front door above the upper hinge on the upper radius of the door. Stiff-backed, retained by screw, mounted on door only.
Hood Bumper
p/n: 27-0103-42
Bumper, hood to fender ledge. Uses four (4) per car.Width: 1.25 inches. Height: .9375 inches.
Fender Bumper
p/n: 33-0441-44
Bumper, between grill and fender. One fourth (1/4) inch thickness, five sixteenths (5/16) inch sheet metal holes.
Headlight Bucket To Fender Gasket
p/n: 20-1542-14
This Headlight Bucket To Fender Gasket is designed from the original part for superior fitment and seal. These gasket fits the headlight bucket and front fender.
Headlight to fender gasket
p/n: 20-2295-14
Gasket, headlight bucket to fender. Cork. Two (2) required per vehicle.
Front and Rear Door Bumper
p/n: 34-0025-42
High quality steel core Front and Rear Door Bumper for front and rear body hinge pillar. Mounted by screw. For auxiliary use only where needed to prevent door rattles. Replaces factory #372341.
Door Bumper
p/n: 50-0203-41
This Door Bumper is used for the fuel filler door on the rear fender. Molded from top-quality EPDM rubber over a steel core for durability. These bumpers are screw retained.
Inner Fender Bumper
p/n: 20-0402-41
This four (4) piece Inner Fender Bumper set are used to plug the holes in the inner fender apron to protect from bumping against the frame. Helps to eliminate squeaks and rattles.
Adjustable Hood Bumper
p/n: 70-0973-42
This Adjustable Hood Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the front fender to support / cushion the hood closure. 1957-1958 models use four (4) per vehicle. 1959-1960 models use two (2) per vehicle.
Multi-Purpose Clips
p/n: 70-4802-45
A ten (10) piece set of Multi-Purpose Clips. Commonly used to retain Hood to Cowl Weatherstrips or Inner Fender Splash Panels.
Hood bumper
p/n: 50-0095-42
Bumper, hood to fender ledge. Self retaining type. See our # 50-0194-42 for center type.
Hood Bumper
p/n: 50-0490-42
Bumper, hood to fender. Uses four (4) per car for most models.Width: 1.375 inches. Height: 1.25 inches.
Hood to Fender Bumper Set
p/n: 20-1312-42
This four (4) piece Hood to Fender Bumper Set is a quality reproduction of the original factory part. This rubber bumper attaches to the front fender to support / cushion the hood closure.