Search Results
Please click on the part name in red in order to get a complete description.
Firewall grommet
p/n: 32-0422-20
Grommet, firewall, speedometer cable through firewall. Two (2) used per car. Sheet Metal Hole: 1-3/16" Center Hole: 1/2" Outside Diameter: 1-7/16" Slot Width: 1/4"
Firewall grommet
p/n: 30-0060-21
Grommet, firewall. For coil wire and temperature gauge line. Excellent workmanship and correct design.Height: 1.0 inches.
Firewall grommet
p/n: 32-0133-21
Special grommet with wide spacing for frame metal, to pass electrical wiring and cables through frame. Sheet Metal Hole: 31/32" Center Hole: 3/4" Outside Diameter: 1-3/16" Slot Width: 3/16"
Firewall grommet
p/n: 32-0001-37
Grommet, firewall and spare wheel sidemount. Sheet Metal Hole: 1-1/8" Center Hole: 3/4" Outside Diameter: 1-9/16" Slot Width: 1/16"
Firewall grommet kit
p/n: 70-1149-21
Grommets, firewall, intended for spark and choke rods, fuel line, oil gauge line and radiator brace rods. Six (6) piece set.
Firewall Grommet Set
p/n: 70-1147-21
Grommet set, firewall, intended for spark and choke rods, fuel line, oil gauge line and radiator brace rods. Six (6) piece set.
Flexible run channel
p/n: 40-0309-57
Channel, side window glass, vertical run. (Use our #40-0280-57 across top).
Front apron crossbar grommet
p/n: 70-1130-45
Grommets, front splash apron crossbar.Width: 3.5 inches. Height: 3.6875 inches.
Front apron crossbar grommet
p/n: 70-1131-45
Grommets, front splash apron crossbar.Width: 3.5 inches. Height: 3.5 inches.
Front bow weatherstrip
p/n: 30-0066-67
Pad, folding top, front frame to windshield. Five sixteenths (5/16) inch by one half (1/2) inch rectangular section, fifty (50) inches long.Length: 50.
Front bumper grommet
p/n: 70-0103-28
Grommets, front bumper. Theses are for the round, tubular bumper support.
Front spring bumper
p/n: 50-0238-35
Bumpers, front spring, Two (2) per car.Width: 2.0 inches. Height: 1.75 inches.
Front spring bumper service
p/n: 15-0006-35
Bumper, front spring to frame. Revulcanization service only.Width: 4.625 inches.
Front spring mounting block
p/n: 11-0015-33
Shock insulator or mounting block, front spring, both ends. Four (4) piece set.
Fuel line grommet
p/n: 30-0045-41
Grommet, fuel gauge and gas line through rear frame cross member. For five eighths (5/8) inch by two and three eighths (2-3/8) inch slot.Length: 2.
Fuel line grommet
p/n: 32-0714-41
Grommet, fuel line and other uses through firewall. Sheet Metal Hole: 1" Center Hole: 3/8" Outside Diameter: 1-5/16" Slot Width: 1/16"
Fuel neck grommet
p/n: 30-0099-41
Grommet, fuel filler neck. Three and one half (3-1/2) inch inside diameter for four (4) inch hole in apron.
Fuel neck grommet
p/n: 30-0232-41
Grommet, fuel filler neck. 2-5/8" inside diameter. Fits 3-3/8" hole in sheet metal. Overall width 4-1/8".
Gearshift boot
p/n: 40-0076-88
Dust boot, gearshift, beehive type. Excellent copy and material. Used on some shift ball sockets.Length: 4.75 inches.
Gearshift floorplate
p/n: 40-0146-88
Floorplate, gearshift and handbrake. Perfect reproduction, including brass core.Length: 8.0 inches. Width: 7.25 inches.
Gearshift floorplate
p/n: 40-0362-88
Draft pad or plate, gearshift and handbrake. Brass core as original.Length: 10.25 inches. Width: 7.0 inches.
Golf Bag Door Weatherstrip
p/n: 70-0118-85
This golf bag door weatherstrip is designed from the original part for superior fitment and seal. This seal mounts directly to the golf bag door.
Handbrake floorplate
p/n: 11-0005-24
Floor plate, handbrake lever. Brass core as original, fully detailed.
Headlight bar grommet
p/n: 11-0002-14
Grommet, headlight bar-to-radiator shell. Includes clearance groove, faithful detail. 1-1/8 inch inside diameter.
Headlight Bracket Pad
p/n: 50-0222-14
Headlight bracket-to-fender pad. POA #1245890-1, right and left.
Headlight grommet
p/n: 25-0039-14
Base, headlight wire conduit and support post. (Vertical post under headlight).
Headlight grommet
p/n: 32-0039-14
Grommet, headlight and horn conduit through fender, made to clear nut on end of conduit. Three (3) per car. Sheet Metal Hole: 15/16" Center Hole: 1/4" Outside Diameter: 1-1/4" Slot Width: 1/16"
Headlight stanchion pad
p/n: 70-0255-21
Mounting pads, horn and headlight stanchion base to hood latch shelf. Two and one half (2-1/2) inches by four and one fourth (4-1/4) inches.Length: 4.
Headlight tube flange gasket
p/n: 50-0223-14
Headlight tube flange gasket. Two (2) per car. Replaces #1234556.
Hood bumper
p/n: 60-0034-42
Bumper stop, hood, lower center. Two (2) required per vehicle.Length: 1.0 inches. Width: .75 inches. Height: .4375 inches.
Hood bumper
p/n: 70-0013-42
Pads, hood hold-down clamp, mount on clamp swivels to hold hood corners in. Set of four (4) rubber pads in solid brass, chrome plated cups.
Hood corner pad
p/n: 40-0128-42
Pads, hood corners. Square type, brass core. Integral installation tabs. 90 degree angle, used on front or rear corners, as required.
Hood hinge top strap pivot
p/n: 70-0045-42
Pivot, hood hinge top strap. Cold rolled steel as original. Furnished in a four and one half (4-1/2) foot strip long enough for all models.
Hood latch swivel
p/n: 70-0061-42
Swivel, hood latch. Exact copy from .075 steel, pierced for rivets, not plated.
Hood latch swivel pad
p/n: 34-0408-42
Pad, hood latch swivel for hood latch pressure against hood corners. For screw or rivet.
Hood ventilator bumper kit
p/n: 70-0011-42
Pad set, hood vent door open limit. Set of twenty (20) pads for one (1) hood, including split rivets for installing.
Inner Fender Seal
p/n: 60-0288-45
Inner Fender Seal for anti-rattle, runningboard apron to body, or fender splash panels. Nine sixteenths (9/16) inch by seven eighths (7/8) inch slotted sponge rubber to accept rivets. Sold in eight (8) foot strips.
Inner side window bumper
p/n: 70-0775-62
Bumper, inner side window garnish molding. One (1) per door.Length: 1.0 inches. Width: .3125 inches. Height: .25 inches.
LaSalle monogram
p/n: 70-0056-49
LaSalle monograms for center of runningboard matting, exact copy, to be in-laid.
LaSalle monogram pedal pad
p/n: 70-0037-22
LaSalle pedal pads, clutch and brake, excellent copy from authentic original with LaSalle monogram.
Motor Mount
p/n: 70-0300-11
Motor mount. Intermediate motor mount for support bolts. Split in half if needed at installation. Four (4) piece set.
Motor Mount
p/n: 70-0443-11
Rear motor support pad at transmission. Four (4) piece set after splitting.
Motor mount pad
p/n: 11-0026-11
Mounting pad, engine. Original pattern, superior workmanship.Qty Required:2 Height: 1.875 inches.
Motor mount pad
p/n: 11-0029-11
Mounting pad, engine. One half (1/2) inch hole, one and five sixteenths (1-5/16) inch outside diameter. Original pattern, superior workmanship.
Motor mount pad
p/n: 50-0266-11
Motor mount pad, rear. Special soft grade rubber, as original. Four (4) piece set.
Motor mount pad
p/n: 11-0028-11
Mounting pad, engine. One half (1/2) inch hole, one and five eighths (1-5/8) inch outside diameter. Original pattern, superior workmanship.
Motor mount pad
p/n: 11-0027-11
Mounting pad, engine. Three eighths (3/8) inch hole, one and five eighths (1-5/8) inch outside diameter.
Motor mount pad
p/n: 25-0038-11
Cushion set, rear motor mounts. Four (4) piece set.Length: 4.4375 inches.
Muffler bypass floor plate
p/n: 11-0006-88
Floor plate, muffler bypass control. Brass core as original, fully detailed.
Parking light mounting pad
p/n: 30-0282-17
Gaskets, parking light (fender light).Length: 2.75 inches. Width: 1.75 inches.
Pressure ring
p/n: 70-0261-69
Pressure ring (washer), sponge rubber, interior door handle and window regulator escutcheon. One and three fourths (1-3/4) inches outside diameter by three eighths (3/8) inch thick.
Radiator brace filler strip
p/n: 70-0020-31
Filler strip, radiator brace rods. Retains ignition wire and thermometer tube in hollow brace rods. Thirty (30) inch strips.
Rear spring bumper
p/n: 60-0137-32
Bumper, rear spring. Fits original retainer.Width: 2.5625 inches.
Rear Spring Pad
p/n: 70-0191-32
Pad, rear spring insulator for two (2) inch wide springs. (see our number 70-0245-32 for two and one fourth (2-1/4) inch springs). Cloth reinforced. Four (4) per vehicle.
Rear spring thrust washer
p/n: 40-0525-32
Thrust washer, rear spring. "Silent Block". Three sixteenths (3/16) inch thick. One (1) inch by one and three fourths (1-3/4) inch.
Rear spring thrust washer
p/n: 40-0526-32
Thrust washer, rear spring. "Silent Block". Three sixteenths (3/16) inch thick. Seven eighths (7/8) inch by one and five eighths (1-5/8).
Rear Window Gasket
p/n: 70-0018-83
This rear window gasket weatherstrip comes in a seven foot, three inch (7' 3") strip and mounts around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Red brake and clutch pedal pad
p/n: 30-0188-89
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0188-22.Length: 3.875 inches. Width: 2.875 inches.
Rigid run channel
p/n: 70-0130-58
Special channel, felt lined rubber, for door upper front post for convertibles with cast upper post. Each piece sixteen (16) inches long.Length: 16.
Rumbleseat lid bumper pad
p/n: 60-0191-87
Bumper pad, rumbleseat lid, upper corners. Compare with our #70-0120-87.Width: 1.0 inches. Height: 1.125 inches.
Rumbleseat lid corner pad
p/n: 70-0120-87
Pad, rumbleseat lid corner, Compare with our #60-0191-87.Length: .75 inches.
Rumbleseat step pad
p/n: 40-0209-44
Pad, rumbleseat step slip over style for original core, "DB" logo.
Rumbleseat step pad
p/n: 60-0126-45
Pad, rumbleseat step, on rear bumper bracket or fender. Rubber cover only, full slip-over type with bowtie emblem.
Rumbleseat step pad
p/n: 40-0012-44
Pad, rumbleseat step bears Chrysler medallion logo in center.Height: .50 inches.
Rumbleseat step pad
p/n: 40-0124-44
Pad, rumbleseat step, with "Dodge" logo, slip over type to fit old steel core. Perfect detail and lettering.Height: .50 inches.
Rumbleseat step pad
p/n: 11-0012-87
Cover, rumbleseat step pad, slipover type, excellent copy.Width: 5.0 inches. Height: 5.0 inches.
Rumbleseat step pad
p/n: 40-0353-44
Pad, rumbleseat step, with "DS" logo. Fits old bracket and bezel. See our #40-0055-44 also.Height: .50 inches.
Rumbleseat step pad
p/n: 40-0050-44
Pad, rumbleseat step, with "P" logo, fully detailed slipover pad for old core. Fits original trim ring.Height: .50 inches.
Rumbleseat Weatherstrip
p/n: 70-0166-85
This rumbleseat weatherstrip is designed from the original part for superior fitment and seal. The strip seals the lower edge of the rumbleseat.
Runningboard matting
p/n: 70-0420-49
Runningboard matting. Fully molded rubber strips with full length steel cores molded in.
Runningboard matting
p/n: 11-0003-49
Edge panel, runningboard. Exact copy including 1/4 inch mounting studs. A perfect replica in highest quality material. 43-1/2 inch long.
Sash channel filler 1/16 cork
p/n: 70-1115-57
Filler strip, window glass sash channel. One sixteenths (1/16) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherstrip type of filler. This is the highest quality linen back, rubber cork composition on
Sash Channel Filler 1/16 Rubber
p/n: 70-2170-57
Filler strip, window glass sash channel. One sixteenths (1/16) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler. This is the highest quality rubber like polymer designed for settin
Sash channel filler 1/32 cork
p/n: 70-1114-57
Filler strip, window glass sash channel. One thirty seconds (1/32) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler. This is the highest quality linen back, rubber cork composition
Sash Channel Filler 1/32 Rubber
p/n: 70-2169-57
Filler strip, window glass sash channel. One thirty seconds (1/32) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler.
Shock absorber arm bushing
p/n: 30-0192-32
Bushing, shock absorber arm. Restore proper shock action.Height: 1.375 inches.
Shock absorber arm bushing
p/n: 15-0005-33
Bushing, shock absorber arm ball joint.Height: .875 inches.
Shock absorber bushing
p/n: 40-0069-32
Bushing, shock absorber link, flanged at both ends. Seven eighths (7/8) inch long between flanges, one (1) inch diameter barrel.
Shock absorber bushing
p/n: 40-0273-32
Bushing. shock absorber link, smaller type. Eight (8) required per car. Compare with our #40-0069-32 (larger type).Length: .9375 inches. Width: .
Shock and stabilizer bushing
p/n: 50-0220-32
Bushing, for shock absorber link cross pin or stabilizer link cross pin.1931-36 Bushing, rubber, for shock absorber link cross pin, #41151.
Side mount spare grommet kit
p/n: 70-1136-37
Grommet set, spare wheel fender mount, for various applications to support arms, brace rods and cowl standoff posts. Six (6) piece set.