Brake and Clutch Shank Seal
p/n: 40-0016-24
Seal, brake and clutch pedal shank to floorboard (draft excluder).Length: 2.4375 inches. Width: 1.875 inches.
Brake and Clutch Shank Seal
p/n: 50-0066-24
Grommet, brake and clutch pedal floor seal.Width: 1.8125 inches. Height: 2.375 inches.
Flexible Run Channel - 30 Inch Pair
p/n: 40-0309-57
Channel, side window glass, vertical run. Flexible, felt lined, rubber covered channel. Available in 30" pair.
Horn trumpet grommet
p/n: 40-0086-21
Grommet for trumpet horn wire through motor cover. Close reproduction. Two (2) per car.
Brake and Clutch Shank Seal
p/n: 40-0175-24
Seal, brake and clutch pedal shank to floorboard. One and one half (1-1/2) inch by two and one eighth (2-1/8) inch by three fourths (3/4) inch thick.
Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Fender Welting 1/4" Bead - 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty-five (25) foot roll. Typically used to attach two (2) fenders to body.
Fuel Neck Grommet
p/n: 40-0067-39
Grommet, fuel filler neck. Oblong, fully molded rubber. Four and one eighth inch (4-1/8") outside length by two and one fourth inch (2-1/4") inside diameter.
Hood Bumper
p/n: 40-0354-42
Bumper, fender to hood. Two (2) per car. Held by four (4) rivets.Length: 2.9375 inches.
Cowl Vent Gaskets
p/n: 40-0170-54
This Cowl Vent Gasket is manufactured from high quality EPDM sponge rubber. For twin cowl vents of thirty four (34") inch circumference.
Rumble Seat Step Pad
p/n: 40-0050-44
Pad, rumble seat step, with "P" logo, fully detailed slipover pad for old core. Fits original trim ring.Height: .50 inches.
Hood Corner Pad
p/n: 40-0128-42
Pads, hood corners. Square type, brass core. Integral installation tabs. 90 degree angle, used on front or rear corners, as required.
Rear Window Gasket
p/n: 70-0084-77
This Rear Window Gasket comes in a seven foot, six inch (7' 6") strip and mounts around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Brake and Clutch Pedal Pads
p/n: 40-0213-22
Pad, brake and clutch pedals. Horizontal oval style, slip over type.Length: 3.8125 inches. Width: 2.375 inches.
Carpet Heel Plate
p/n: 40-0087-88
Heel pad for carpet. Identical to original. Five and three fourths (5-3/4) inch by ten and one half (10-1/2) inch, to be stitched in place.Length: 10.
Accelerator Pedal Service - Brown
p/n: 40-0201-89
Revulcanization Service Only for Brown Rubber Accelerator Pedal Pad. For Black see our #40-0201-40.
Fender Welting 1/4" Bead - 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body.
Chrome Fender Welting - 50ft
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Fender Welting with 3/16" Bead - 50ft
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Accelerator Pedal Pad Service - Black
p/n: 40-0201-40
Revulcanization Service Only for Black Rubber Accelerator Pedal Pad. For Brown see our #40-0201-89.
Door Check Strap
p/n: 40-0535-70
Strap, door check. T-type, special heavy duty construction of rubber with multiple ply webbing and molded-in steel crossbar. Full length as original with one eighth (1/8) inch by seven eighths (7/8) inch steel crossbar.
Gearshift Floorplate
p/n: 40-0049-88
Floorplate, gearshift and handbrake. Includes brass core and mounting holes.Length: 10.5625 inches. Width: 6.125 inches.