Fuel Neck Grommet
p/n: 40-0091-39
Grommet, fuel filler neck. Fully molded large oval style. Bottom is flat. Four and one half inch (4-1/2") outside width by five by one half inch (5-1/2") outside length. Two and five sixteenths inch (2-5/16") inside hole diameter.
Brake Master Cylinder Filler Access Hole Cover
p/n: 60-0016-24
This Master Cylinder Access Hole Cover is designed from the original part for superior fitment and seal. Secures the Brake Master Cylinder Filler and Inspection Access Hole in the vehicle.
Rumble Seat Step Pad
p/n: 40-0050-44
Pad, rumble seat step, with "P" logo, fully detailed slipover pad for old core. Fits original trim ring.Height: .50 inches.
Front Spring Bumper
p/n: 50-0423-35
Bumper, front spring. Fits onto original bracket.Length: 2..125 inches. Width: 2.0 inches. Height: 1.875 inches.
Clutch and Brake Pedal Pads - BLACK
p/n: 25-0024-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. A reproduction with authentic type ribbing, to replace worn original pedal pads. Manufactured in Black rubber.
Beltline Weatherstrips
p/n: 70-1121-61
These Beltline Weatherstrips (sometimes called "scraper seal") come in a three (3) foot pair. For use on front, rear, and quarter windows without a chrome reveal molding at the window beltline. Available in 3ft pair.
Fuel Neck Grommet
p/n: 50-0217-39
Grommet, fuel filler neck. Fully molded rubber. Four and one half inch (4-1/2") outside diameter by two and one eighths inch (2-1/8") inside diameter by thirteen sixteenth inch (13/16") height.
Axle Rebound Pad
p/n: 50-0265-35
Bumpers, rear axle to frame.Width: 2.0 inches. Height: 1.25 inches.
Windshield Gasket
p/n: 40-0320-52
This Windshield Gasket comes in a four (4) foot strip and is for the lower glass frame to cowl. This weatherstrip is for 2 piece windshields.
Hood Corner Pad
p/n: 40-0128-42
Pads, hood corners. Square type, brass core. Integral installation tabs. 90 degree angle, used on front or rear corners, as required.
Rear Window Gasket
p/n: 70-0084-77
This Rear Window Gasket comes in a seven foot, six inch (7' 6") strip and mounts around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Fuel Filler Neck Grommet
p/n: 30-0158-41
This Fuel Filler Neck To Body Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler neck between the filler neck and vehicle body.
Quarter Window Weatherstrip
p/n: 60-0446-77
Weatherstrip, stationary quarter windows. Eight (8) foot strip for two (2) quarter windows. Most models with stationary windows.Length: 96.0 inches.
Windshield Weatherstrip
p/n: 60-0004-52
This Windshield Weatherstrip is made of a high-quality EPDM dense rubber extrusion. The four (4) foot strip mounts on the lower windshield for easy installation.
Clutch and Brake Pedal Pads - BROWN
p/n: 25-0024-89
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. A reproduction with authentic type ribbing, to replace worn original pedal pads. Manufactured in Brown rubber.
Parking Light Mounting Pad
p/n: 70-0253-16
Pads, parking light to fender mounting.Length: 2.875 inches.
Windshield filler
p/n: 40-0318-52
Seal, windshield outer trim. Four (4) piece set for top and bottom of division post trim and for right and left lower corners of windshield panels.
Hood Corner Pad
p/n: 40-0127-42
Pads, hood corners, brass core. Approximately 80 degree angle. Integral tabs for installing.Length: 1.50 inches.
Accelerator Pedal Pad - Black
p/n: 50-0080-40
Accelerator pedal pad manufactured in Black rubber. Full slip-over type and a perfect copy. For Brown see our #50-0080-89.
Headlight Mounting Pad
p/n: 70-0259-14
Mounting pads, headlight bar to radiator shell brace rod (at shell).
Door Bumper
p/n: 40-0262-70
Bumper, door.Chrysler 1934 Bumper, door. Chrysler 1932-34 Bumper, decklid. Two (2) required per car. Length: 2.50 inches. Width: 1.8125 inches.
Fuel Neck Grommet
p/n: 50-0059-39
Grommet, fuel filler neck. Fully molded rubber. Four and five eighths inch (4 5/8") outside diameter by two and three sixteenths inch (2-3/16") inside diameter by three fourths inch (3/4") height.
Hood Corner Pad
p/n: 50-0036-42
Pads, hood corners, front. Original type with metal core and retaining tab.Width: 1.625 inches.
Body to Frame Webbing
p/n: 20-1599-48
This Body to Frame Webbing is designed from the original part for superior fitment and function. This webbing is used to shim the body to the frame. Also used as a noise reducer material. Webbing is two (2) inch wide, twenty-five (25) foot long roll.
Windshield Post To Door Weatherstrips
p/n: 20-2092-63
These Windshield Post To Door Weatherstrips attach to the body and seals between the windshield A-post and the front section of the door or vent window frame when the door is closed. Includes special molded foot. Fits one (1) inch wide channel.
Steering Column Floorplate
p/n: 17-0001-36
Grommet, steering column floor, black rubber only, excellent copy of original.Length: 5.0 inches.
Brake and Clutch Pedal Pads
p/n: 40-0213-22
Pad, brake and clutch pedals. Horizontal oval style, slip over type.Length: 3.8125 inches. Width: 2.375 inches.
Hood Louver Corner Stop
p/n: 33-0129-42
Corner stop, hood louver, self-holding, original size and profile, fits one fourth (1/4) inch hole in sheet metal.
Accelerator Pedal Pad - Brown
p/n: 50-0080-89
Accelerator pedal pad manufactured in Brown rubber. Full slip-over type and a perfect copy.
Rear Bumper Grommet
p/n: 60-0406-28
Grommets, rear bumper. Right and left sides. Left side has clearance for tail light wire.
Headlight Mounting Pad
p/n: 30-0145-14
Pads, headlight bracket to fender mounting. Proper edge form.Length: 4.375 inches.
Brake and Clutch Pedal Pads
p/n: 30-0188-22
Pads, brake and clutch pedal, slip over type. Black rubber only. For black and red (semi-automatic clutch models) see our #30-0188-89.Length: 3.875 inches.
Carpet Heel Plate
p/n: 40-0087-88
Heel pad for carpet. Identical to original. Five and three fourths (5-3/4) inch by ten and one half (10-1/2) inch, to be stitched in place.Length: 10.
Rear Bumper Grommet
p/n: 40-0180-30
Grommet, rear bumper support bar to gas tank apron. One and three fourths (1-3/4) inch inside diameter.
Rear Spring Bumper
p/n: 60-0137-32
Bumper, rear spring. Fits original retainer.Width: 2.5625 inches.
Rear Bumper Grommet
p/n: 40-0296-30
Grommets, rear bumper clamp to frame end. Comes as a four (4) piece set. Fully molded rubber.
Rumble Seat Step Pad
p/n: 40-0055-44
Pad, rumble seat step, with "DeSoto" logo, full slipover type to fit old carcass and outer trim ring. See also our #40-0353-44.Height: .50 inches.
Clutch and Brake Pedal Pads - Black
p/n: 50-0077-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Brake and Clutch Pedal Pads
p/n: 40-0038-22
Pad, brake and clutch pedal. See also our #40-0072-22.Length: 3.8125 inches. Width: 2.3125 inches.
Rumble Seat Step Pad
p/n: 40-0353-44
Pad, rumble seat step, with "DS" logo. Fits old bracket and bezel. See our #40-0055-44 also.Height: .50 inches.
Hood Corner Pad
p/n: 30-0225-42
Pads, front and rear hood corners, brass core, right angle.Length: 2.625 inches. Width: 2.625 inches.
Steering Column Grommet
p/n: 70-1512-36
Insulator, steering column bracket. Two (2) pieces of extruded rubber like original.Width: 1.3125 inches.
Red Brake and Clutch Pedal Pad
p/n: 30-0188-89
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0188-22.Length: 3.875 inches. Width: 2.875 inches.
Accelerator Pedal Service - Brown
p/n: 40-0201-89
Revulcanization Service Only for Brown Rubber Accelerator Pedal Pad. For Black see our #40-0201-40.
Engine Mount Pad
p/n: 70-0741-11
This Engine Mount Pad pair is used as an intermediate support cushion. Made of rubber only to install in your original case.
Windshield Mounting Pad
p/n: 60-0360-52
Pad, windshield lower weatherstrip, retainer-to-cowl.Length: 44.0 inches. Width: 1.5625 inches.
Sidemount Wheel Carrier Grommet
p/n: 60-0002-37
This Sidemount Wheel Carrier Grommet for the wheel carrier brace support-at-cowl panel. Manufactured with a heavy brass core. Has a flexible neck. A close copy of original.
Front Spring Bumper
p/n: 60-0021-35
Rebound bumper, front spring and rear spring for beam axle cars, steel ring reinforced as original.Height: 2.4375 inches.
Chrome Fender Welting - 50ft
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Fender Welting 1/4" Bead - 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body.
Fender Welting with 3/16" Bead - 50ft
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Brake and Clutch Pedal Pads
p/n: 40-0072-22
Pad, brake and clutch pedal.Length: 3.9375 inches. Width: 2.9375 inches.
Rumble Seat Step Pad
p/n: 40-0012-44
Pad, rumble seat step bears Chrysler medallion logo in center.Height: .50 inches.
Front Spring Bumper
p/n: 50-0238-35
Bumpers, front spring, Two (2) per car.Width: 2.0 inches. Height: 1.75 inches.
Shock absorber arm seal
p/n: 40-0081-32
Dust seal set, shock absorber link, rubber only. Eight (8) piece set.
Hood Corner Pad
p/n: 60-0042-42
Pads, hood corners, right and left. Four (4) piece set.Width: 1.125 inches. Height: 1.125 inches.
Rear Spare Wheel Carrier Seal
p/n: 40-0141-37
Grommet, rear spare wheel carrier.Some models require 3 pieces (1-1/2 prs).Length: 3.375 inches.
Rumble Seat Step Pad
p/n: 60-0501-45
Step pad, rumble seat, on rear fender, with bowtie emblem. Steel core with bolt.Width: 4.375 inches. Height: 5.25 inches.
Carpet Heel Plate
p/n: 70-0617-88
Heel mat, front carpet insert.Length: 13.5625 inches. Width: 9.75 inches.
Brake Vacuum Cylinder Rod Boot
p/n: 70-0485-24
This Brake Vacuum Cylinder Rod Boot is designed from the original part for superior fitment and function. For piston type vacuum cylinders.
Rumble Seat Step Pad
p/n: 40-0124-44
Pad, rumble seat step, with "Dodge" logo, slip over type to fit old steel core. Perfect detail and lettering.Height: .50 inches.
Cadillac V-8 Pedal Pad
p/n: 70-0148-22
Cadillac V-8 pedal pads, clutch and brake. Another rare one we finally found to copy. Superior copy.
Swing-Out Windshield Weatherstrip Set
p/n: 40-0171-52
This three (3) piece Swing-Out Windshield Weatherstrip Set is designed for superior fitment, finish and function. Three (3) piece set, consisting of stationary weatherstripping for bottom and sides.
Side Mount Grommet
p/n: 30-0041-37
Grommets, sidemount support arm, right and left.Length: 5.50 inches. Width: 4.25 inches.
Engine Mount Pad
p/n: 30-0156-11
This Engine Mount Pad pair is used as an insulator cushion. These pads are the rectangular ring type. Made of a high-quality EPDM rubber.
Luggage Rack Grommet
p/n: 17-0021-46
Grommet, luggage rack support arm through body.Length: 2.25 inches. Width: 1.25 inches.
Swing-Out Windshield Weatherstrip
p/n: 40-0033-52
This Swing-Out Windshield Weatherstrip comes in an eleven (11') foot strip. The seal slides into the track (channel) attached to the glass that goes all the way around the windshield and creates a seal when the glass is pressed against the body of the vehicle.
Horn Cover Bumper
p/n: 30-0283-21
Bumpers, horn cover. Rubber with brass core construction like original.Length: 4.0 inches. Width: .625 inches.
Engine Mount Pad
p/n: 70-1161-11
This Engine Mount Pad pair is designed from the original for an exact original configuration. For cars with round cone-type front mounts.