Search Results
Vibration damper service
p/n: 30-0376-12
Vibration damper, crankshaft, front. Revulcanizing service for rubber cushion elements.
Hood hinge top strap pivot
p/n: 70-0045-42
Pivot, hood hinge top strap. Cold rolled steel as original. Furnished in a four and one half (4-1/2) foot strip long enough for all models.
Door check strap
p/n: 40-0535-70
Strap, door check. T-type, special heavy duty construction of rubber with multiple ply webbing and molded-in steel crossbar. Full length as original with one eighth (1/8) inch by seven eighths (7/8) inch steel crossbar.
Headlight mounting pad set
p/n: 30-0236-14
Pad set, headlight mounting. Six (6) piece replacement set. Sold in complete sets only.
Motor mount service
p/n: 30-0185-11
Insulator, motor support, rear assembly. Revulcanization service only.
Motor mount service
p/n: 30-0184-11
Motor mount, motor stabilizer bracket, right hand side. Revulcanization service only.
Headlight mounting pad set
p/n: 30-0161-14
Pad and Grommet Set, headlight support bar to radiator shell. Four (4) piece set, sold in complete sets only.
Windshield weatherstrip
p/n: 30-0083-52
Pad/Seal, windshield frame, lower. Forty six (46) inches overall.Length: 46.0 inches.
Axle rebound pad
p/n: 30-0054-32
Pads, rear axle rebound.Length: 5.125 inches. Width: 1.4375 inches.
Shock absorber bushing
p/n: 30-0407-33
Bushings, shock absorber. Set includes eight (8) large and eight (8) smaller bushings.
Axle rebound pad
p/n: 30-0043-32
Pads, front axle rebound. Correct shape and design like original.Length: 3.625 inches. Width: 2.125 inches. Height: 2.125 inches.
Swing-out Windshield Weatherstrip
p/n: 70-0057-52
This swing-out windshield weatherstrip comes in an twelve foot (12') strip and mounts into the metal channel attached to the glass. The rubber slides into the T-groove and creates a seal when the glass is pressed against the body of the vehicle.
Steering column grommet
p/n: 30-0160-36
Grommet, steering column to toe board. One and five eighths (1-5/8) inch hole for column. Similar to, but larger than our #30-0046-36.Length: 5.25 inches.
Horn cover bumper
p/n: 30-0283-21
Bumpers, horn cover. Rubber with brass core construction like original.Length: 4.0 inches. Width: .625 inches.
Side mount grommet
p/n: 30-0041-37
Grommets, sidemount support arm, right and left.Length: 5.50 inches. Width: 4.25 inches.
Fender welting 1/4" bead 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Fender welting 3/16 bead 50ft
p/n: 70-1100-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty fi
Fender welting 50ft chrome
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Cowl vent gasket
p/n: 30-0097-54
Gaskets, side cowl vent. One fourth (1/4) inch square cross section.
Red brake and clutch pedal pad
p/n: 30-0188-89
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0188-22.Length: 3.875 inches. Width: 2.875 inches.
Hood corner pad
p/n: 30-0225-42
Pads, front and rear hood corners, brass core, right angle.Length: 2.625 inches. Width: 2.625 inches.
Headlight mounting pad
p/n: 30-0145-14
Pads, headlight bracket to fender mounting. Proper edge form.Length: 4.375 inches.
Brake and clutch pedal pad
p/n: 30-0188-22
Pads, brake and clutch pedal, slip over type. Black rubber only. For black and red (semi-automatic clutch models) see our #30-0188-89.Length: 3.875 inches.
Taillight mounting pad
p/n: 30-0148-15
Mounting pad, taillight bracket to fender, with correct beading and shape.Length: 4.5625 inches. Width: 1.875 inches.
Brake cable anti-rub cover
p/n: 60-0443-24
Sleeve, rear brake cable anti-rub. Six (6) piece set. One half (1/2) inch inside diameter, seven eighth (7/8) inch outside diameter.
Radiator mounting pad
p/n: 30-0395-31
Spacer or Pad, radiator anchorage stud, upper stud. One (1) pair required per car.Length: 2.5625 inches.
Cowl vent gasket
p/n: 30-0096-54
Gasket, top cowl vent. Closed cell sponge rubber. One half (1/2) inch by three fourths (3/4) inch. Rectangular cross section.
Firewall grommet
p/n: 30-0056-21
Grommet, firewall, for ignition cable and thermometer tube. For two and one half (2-1/2) inch hole in sheet metal.
Hood rest pad
p/n: 30-0222-42
Pads, hood inner rest center. Rubber only, fits original bracket.Length: 2.0625 inches. Width: .6875 inches.
Motor Mount
p/n: 30-0292-11
Motor crank case link ball insulator. One (1) pair per car. Sold only in pairs.
Radiator mounting pad
p/n: 30-0209-31
Shim, radiator core mounting stud spacer. Fully molded rubber. Use as required. Comes as a pair of two (2). Two and seven eighths inch (2 7/8") square by five eighths inch (5/8") inside hole diameter by three eighths inch (3/8") height.
Fender welting 1/4" bead 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For
Fender welting 25ft chrome
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Fender welting 3/16 bead 25ft
p/n: 70-1099-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, twenty five (25) foot roll. Typially used for attaching two (2) fenders to body. For f
Brake and clutch pedal bumper
p/n: 30-0380-20
Bumper, inclined toe board pedal hole, carried on toe board to meet our #30-0055-24 pedal. dust cover.
Brake and clutch shank seal
p/n: 30-0055-24
Seals, brake and clutch pedal shanks, against underside of floorboard.Length: 2.5625 inches. Width: 1.75 inches.
Parking light mounting pad
p/n: 30-0447-17
Pad, parking light to fender. Requires two (2) per car.Length: 4.125 inches.
Radiator mounting pad
p/n: 30-0451-31
Spacer or Pad, lower radiator anchor stud. Used in conjunction with our #30-0395-31.Height: .3125 inches.
5" Wide Bowdrill Cloth Tape
p/n: 70-1175-65
Bowdrill cloth tape is used for covering convertible side window weatherstrip. Available in a 5 ft roll.
Taillight gasket
p/n: 30-0523-15
Gasket, taillight door. Two (2) strips twelve (12) inches long.Length: 12.0 inches. Width: .25 inches.
Shock absorber arm bushing
p/n: 30-0192-32
Bushing, shock absorber arm. Restore proper shock action.Height: 1.375 inches.
Door bumper
p/n: 30-0152-71
Bumper, door, rubber, round style, screw retained. One and five sixteenths (1-5/16) inch diameter.
Battery clamp cover
p/n: 70-0095-21
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Door bumper
p/n: 30-0002-71
Bumper, door side. One and one fourth (1-1/4) inch by two (2) inch.Length: 2.0 inches. Width: 1.25 inches.
2-1/2" Bowdrill Cloth Tape
p/n: 70-1172-65
Bowdrill cloth tape is used for covering convertible side window weatherstrip. Available in a 5 ft roll.