Grommets, sidemount. These are the very large type, right and left. Used simultaneously with our #70-0388-37. Compare with your original. (See also our #70-0388-37).
Grommets/seals, for sidemounted spares, cover hole in fender. Large, fully flanged for fender metal, compare to our #70-0341-37 and your original. Symmetrical, right and left. Approximately five and three fourths (5-3/4) inches by eight (8) inches outside
Hoses, carburetor air intake. Two (2) per car. Sixteen and three fourths (16-3/4) inches long, two (2) inches inside diameter one end, two and one fourth (2-1/4) inches inside diameter other end. Trim to proper length when installing.
This eight piece kit includes the inner and outer windowfelts, upper rigid run channels, and flexible run channels needed to complete two doors. Used for front or rear doors in models with vent windows in the door.
Radiator hoses, fluted style. V-12, V-16.
Grommets, spare wheel sidemount arm.
Weatherstrip, rear door vent. Note: we do not have a matching metal core division post seal for this part. Please order our part #70-0040-56 separately.
Bumper, front spring, upper arm on frame. Rubber with heavy steel core, including five sixteenths (5/16) inch stud.
Grommets, rear bumper. For vehicles without luggage racks.
This front door vent window weatherstrip set is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
This six (6) piece kit includes the inner and outer windowfelts and flexible run channels needed to complete two (2) doors. Used for front or rear doors in models without vent windows in the door.
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Weatherstrip, front bow-to-windshield, soft rubber, hollow body, proper screw holes, hinged flaps front and back.
Pivot, hood hinge top strap. Cold rolled steel as original. Furnished in a four and one half (4-1/2) foot strip long enough for all models.
Grommets, ride regulator control rod through fender splash shield. Two (2) per car.Length: 5.875 inches. Width: 1.75 inches.
Installing tool, door and trunk handle ferrule. For cars and trucks using door and trunk handle ferrules such as our #70-0111-69.
Pad, motor support, rear. Revulcanization service only. Send in your old plates with studs intact. Rebound cushion, furnished with mount.
Grommet kit, rear spare wheel mount for cars without luggage rack. Three (3) piece set consisting of two (2) large grommets, one (1) small grommet.
Protector, hood center. Brass core as original threaded to fit original screws.
Seals, shock absorber and rear stabilizer link. Eight (8) piece set.
Pads, headlight to bracket mounting.Length: 11.0 inches.
Mounting pads, headlight bracket to fender, right and left. Length: 11.375 inches.
Grommets, luggage rack brace rod through body. Styles with luggage rack arms.
Bumper, front spring lower arm.
Pads, hood corners. right and left. Threaded brass core.
Cushion strip for large hubcap (wheel cover). Original type, replaces that old brittle rubber to keep from losing the cover. Set of four (4) strips, approximately four (4) foot long, enough for all four (4) wheels.
Boot, vacuum brake cylinder main rod. Accordion type, two (2) inches diameter by six (6) inches. Top quality workmanship and material.Length: 6.0 inches.
Cadillac Motors pedal pads. Authentic straight diamond pattern. Especially good copy, fine detail.
Seals, shock absorber and rear stabilizer link. Eight (8) piece set.Width: 1.1875 inches.
Pads, hood corner, right and left. Threaded brass core.
Pad, taillight mounting. Double bead as original.
Grommets, front bumper. Theses are for the round, tubular bumper support.
Motor mount pad. Cloth base as original, low type, two (2) inches outside diameter by seven eighths (7/8) inch thick.
Bumper, hood ventilator door, self retaining. Five sixteenths (5/16) inch diameter, forty eight (48) piece set.
Boot, brake vacuum cylinder rod, for piston type vacuum cylinder.
Shield, gearshift through floorboard, molded in all detail, including bolt holes.Length: 7.5 inches. Width: 5.875 inches.
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty fi
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Front motor mount pad. Thick type, cloth base as original. Two and five eighths (2-5/8) inch outside diameter by one and seven eighths (7/8).
Mounting pad, filler neck extension. Four and nine sixteenths (4-9/16) inches diameter, double bead.
Pad, door jamb edge. With metal insert as original.Length: 1.1875 inches. Width: 1.5625 inches.
Knob, gearshift. Rubber only for flanged top nut on gearshift lever.
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
Sleeve, coil wire to distributor. Fluted to match upper water hoses rubber only. V-12 & V-16 with coils mounted in radiator, V-8 with coils mounted horizontally on brace rods.
Inner Fender Seal for anti-rattle, running board apron to body, or fender splash panels. Nine sixteenths (9/16) inch by seven eighths (7/8) inch slotted sponge rubber to accept rivets. Sold in eight (8) foot strips.
Boot, gearshift. Brown rubber. For black see our #50-0035-24.Color:brown Width: 2.8125 inches.
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Seal, steering column to toe board. Three fourths (3/4) inch thick, high grade sponge, die cut holes.Length: 3.875 inches. Width: 3.875 inches.