Runningboard matting. Fully molded right and left hand. Top quality rubber, flawless detail. Includes rubber cross molding for in front of rear fender.
Support assembly, rear of engine right and left. Revulcanization service only.
Bushing and pin assembly cartridge. Inlox type, front wheel lower support arm inner pin. Shipped with instructions for reinstalling.Length: 5.75 inches.
Bumper assembly, front suspension inside coil spring, with five sixteenths (5/16) inch threaded studs as found originally.
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts but both strips need to be cut in to three (3) sections to facilitate installation. Instruction sheet included showing how to make a six (6) piece set.
Bushing assembly, front wheel support; upper and outer. Inlox type cartridge bushing assembly.
Stabilizer, fore and aft transmission to frame. A factory service part used to remedy clutch chatter. Steel core as original.Length: 7.50 inches.
Bushing assembly, rear spring, front. Inlox cartridge type.
Bushings, front suspension torque arm. Necessary for proper front end geometry.
Bumper assembly, front spring rebound (upper arm). Steel core, with treaded stud just like original.
Pads, rear axle rebound.Length: 5.125 inches. Width: 1.4375 inches.
Pads, front axle rebound. Correct shape and design like original.Length: 3.625 inches. Width: 2.125 inches. Height: 2.125 inches.
Grommets, rear bumper. Molded right and left as original.Length: 4.875 inches. Width: 3.125 inches.
This swing-out windshield weatherstrip comes in an twelve foot (12') strip and mounts into the metal channel attached to the glass. The rubber slides into the T-groove and creates a seal when the glass is pressed against the body of the vehicle.
Grommets, front bumper. Molded right and left, including retaining flange. Fully molded rubber. Three and fifteen sixteenths inch (3-15/16") outside length by two and five eighths inch (2-5/8") outside width by one and one half inch (1-1/2") inside hole l
Pedal, accelerator. Revulcanization service only. Includes new ball sockets as original, with correctly detailed tread pattern.Length: 9.625 inches.
Cushion, upper (thin) spare wheel in fender well. Two (2) per car.Length: 11.25 inches. Width: 3.0 inches.
Grommets, rear bumper. For models with luggage racks.Length: 4.125 inches. Width: 3.375 inches.
Cushions, motor support, at timing gear cover. One (1) pair required per car. Sold only in pairs.
Insulator, front coil springs.
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty fi
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Channel, rigid run, for division bar opposite vent windows.
Cushion, lower (thick) spare wheel in fender well. Two (2) per car.Length: 11.0 inches. Width: 3.0 inches.
Pads, hood front corners. 2 rivet type.Length: 3.25 inches.
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0188-22.Length: 3.875 inches. Width: 2.875 inches.
Gaskets, headlight stanchion.Length: 11.25 inches.
Gaskets, taillight mounting. Proper type lip as original. One and eleven sixteenths (1-11/16) inch by four and one half (4-1/4) inch.Length: 4.25 inches.
Pads, brake and clutch pedal, slip over type. Black rubber only. For black and red (semi-automatic clutch models) see our #30-0188-89.Length: 3.875 inches.
Grommet, fuel filler neck. For inside of body, on floor of wheel carrier.
Pad, radiator lower splasher to grille. Fastens into place with rivets. One four (4) piece set required per car.Length: .875 inches. Width: .875 inches.
Grommet, fuel filler neck.
Sleeve, rear brake cable anti-rub. Six (6) piece set. One half (1/2) inch inside diameter, seven eighth (7/8) inch outside diameter.
Grommets, spare wheel sidemount brace, lower.Length: 2.625 inches. Width: 2.50 inches.
Gasket, cowl vent, original labyrinth type, not sponge.Length: 14.75 inches. Width: 5.50 inches.
Weatherstrip, door window inner and outer, front and rear doors. Bend to fit. Available in a 3ft pair.
Gasket, rumbleseat step center.Length: 5.875 inches.
Boot, brake and clutch pedal shank at toe board.Length: 2.9375 inches.
Grommet, steering column at toe board.
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Gasket, rumbleseat step. For left hand drive upper.Length: 5.0 inches.
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, twenty five (25) foot roll. Typially used for attaching two (2) fenders to body. For f
Bumpers, rumbleseat stop bracket. Self retaining type as original.Length: 1.1875 inches. Width: .75 inches. Height: .375 inches.
Bumper, inclined toe board pedal hole, carried on toe board to meet our #30-0055-24 pedal. dust cover.
Bowdrill cloth tape is used for covering convertible side window weatherstrip. Available in a 5 ft roll.
Gaskets, taillight door lens. For cars without center license light. Two (2) strips eleven and one half (11-1/2) inches long each.Length: 11.5 inches.
Pad, door jamb (Atwood type), one and five eighths (1-5/8) inch long.Width: 1.5625 inches. Height: 1.375 inches.
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.