Horn Button Contact Cushion
p/n: 60-0192-21
Cushion, standard steering wheel horn button contact. Two and one half (2-1/2) inch diameter.
Gearshift Boot - At Floor
p/n: 60-0108-24
This Gearshift Boot is designed from the original part for superior fitment and function. Cup style boot to fit over the gear shifter stick at the floorboard.
Shock Absorber Bushing
p/n: 30-0024-33
Bushings, rear shock link assembly. Designed to act like sleeve inside link arm.Height: .9375 inches.
Firewall Grommet Set
p/n: 50-0048-20
This Firewall Grommet Set contains two (2) pieces including one (1) round grommet for temperature and oil pressure lines and one (1) oval grommet for vacuum lines, throttle, choke, and speedometer cables.
Antenna Boot
p/n: 70-0212-21
This Antenna Boot is designed from the original part for superior fitment and function. This boot fits at the vehicle running board antenna wire connection.
Horn Button Contact Ring
p/n: 60-0157-21
Ring, horn button contact. Accessory banjo steering wheel. Four and one eighth (4-1/8) inch outside diameter.
Flexible Run Channel - 30 Inch Pair
p/n: 40-0309-57
Channel, side window glass, vertical run. Flexible, felt lined, rubber covered channel. Available in 30" pair.
Fender Welting
p/n: 20-1590-44
This black Fender Welting is designed from the original part for superior fitment and seal. This welting material fits between the fenders and the vehicle body. Thirty (30) foot roll.
Gearshift Seal
p/n: 60-0471-24
This Gearshift Seal is designed from the original part for superior fitment and function. For the gearshift at floor.
Gearshift Boot
p/n: 50-0035-24
Boot, gearshift. Black rubber. For brown see our #50-0035-89.Width: 2.8125 inches.
License Light Mounting Pad
p/n: 40-0174-17
Pad, license light mounting. Plain type without edge bead as original.Length: 8.0 inches. Width: 3.25 inches.
Battery Carrier Edge Liner
p/n: 60-0112-21
Edge liner, battery carrier cover.Length: 42.0 inches. Width: .25 inches. Height: .6875 inches.
Side Mount Cover Pad
p/n: 70-0077-37
Pads, channel type, for sidemount covers. Eight (8) piece set.Width: .25 inches. Height: .6875 inches.
Engine and Transmission Mount
p/n: 20-1978-11
This Engine and Transmission Mount is designed from the original part for superior fitment and function. This engine mount works to absorb and isolate engine and driveline vibrations. The set services one mount. 1937-1941 require four (4) sets for both Front and Rear. 1942-1948 require two (2) sets.
5" Wide Bow Drill Cloth Tape
p/n: 70-1175-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Brake and Clutch Shank Seal
p/n: 50-0066-24
Grommet, brake and clutch pedal floor seal.Width: 1.8125 inches. Height: 2.375 inches.
Trunk Weatherstrip
p/n: 20-1688-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. This sponge rubber weatherstrip mounts around the full perimeter of the trunk directly to the body.
Side Mount Grommet
p/n: 40-0533-37
Grommets, sidemount. Please see sketches and specify #40-0533-37 or #40-0534-37 when ordering.
Starter Pedal Bellows
p/n: 60-0487-21
Bellows, starter pedal shaft-to-floorboard. One and three fourths (1-3/4) inch by two and one fourth (2-1/4) inch.Length: 2.25 inches. Width: 1.75 inches.
Trunk Hinge Mounting Pad
p/n: 60-0139-87
Pad, trunk hinge mounting, upper and lower. Four (4) piece set.
Accelerator Rod Seal
p/n: 40-0205-88
This Accelerator Rod Seal is used as an accelerator rod through the toeboard. Molded from a high-quality EPDM dense rubber.
Side mount grommet
p/n: 40-0534-37
Grommets, sidemount. Please see sketches and specify #40-0533-37 or #40-0534-37 when ordering.
Brake and Clutch Shank Seal
p/n: 40-0016-24
Seal, brake and clutch pedal shank to floorboard (draft excluder).Length: 2.4375 inches. Width: 1.875 inches.
Firewall Grommet
p/n: 40-0222-21
This Firewall Grommet is used to run the throttle cable and wiper vacuum line through the firewall as well as a drain hole for the cowl vent. The holes in the three (3) hole design measure: 9/16", 3/8", and 1/4".
Horn projector grommet
p/n: 60-0161-21
Grommet, horn trumpet through horn mounting bracket. For Deluxe country horn.
Trunk Weatherstrip
p/n: 20-2265-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Firewall Grommet
p/n: 70-1203-20
This Firewall Grommet is used to run various electrical and dash gauge wires through the firewall. Also see our 32-1201-20 and 32-0225-20.
Taillight Lens Gasket
p/n: 30-0336-15
Gaskets, taillight door lens. For cars without center license light. Two (2) strips eleven and one half (11-1/2) inches long each.Length: 11.5 inches.
Clutch and Brake Pedal Pads - Black
p/n: 50-0054-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Cowl Vent Gasket
p/n: 60-0087-54
Gasket, cowl vent, lip type. Sponge rubber, for three and seven eighths (3-7/8) inch by fifteen (15) inch cowl vent.Length: 15.0 inches. Width: 3.
Door Weatherstrips
p/n: 20-0390-72
This Door Weatherstrip is designed from the original part for superior fitment, finish and function. This rectangular sponge rubber extrusion is made of a superior grade, 100% EPDM rubber. It is designed to last- it will not fade, shrink or crack. Excellent at resisting moisture, Ozone and UV exposure.
Firewall Grommet
p/n: 40-0221-21
This Firewall Grommet is used to run the speedometer cable, oil tube, and the temperature tube through the firewall. The three (3) holes measure 5/16", 1/4", 3/16".
Firewall Grommet
p/n: 50-0272-20
This Firewall Grommet is used to run the water temperature indicator pipe through the dash. Designed from the original part for superior fit and seal.
Starter Button Cover
p/n: 60-0322-21
This Starter Button Cover is designed from the original part for an authentic fit, finish, and appearance. A push on replacement to rod. Two (2") inch outside diameter.
Transmission Mounting Pad
p/n: 50-0228-25
Pad, transmission support. Two (2) per car.Height: .5 inches.
Cowl Vent Gasket
p/n: 20-1613-54
This Cowl Vent Gasket is designed from the original part for superior fitment and seal. Manufactured to OEM specifications to install for an authentic fit and finish.
Trunk Weatherstrip
p/n: 70-0798-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Brake and Clutch Pedal Pads
p/n: 20-2307-22
Brake and Clutch Pedal Pad pair. Molded on metal like original. Exact pyramid design. 1937-1940 Ford Trucks.
Taillight Mounting Pad
p/n: 60-0495-15
Pad, taillight bracket to fender. Can be used for right or left hand. Two and one half (2-1/2) inch by three and five eighths (3-5/8) inch overall.
Horn trumpet grommet
p/n: 70-0302-21
Grommets, horn projector. For under hood horn brackets. Two (2) per car.
Rear Spring Pad
p/n: 70-0245-32
Pad, rear spring insulator for two and one fourth (2-1/4) inch wide springs. (see our number 70-0191-32 for two (2) inch springs). Four (4) per vehicle.
Rear Window Gasket
p/n: 30-0086-83
This Rear Window Gasket comes in a seven (7) foot strip and mounts around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Clutch and Brake Pedal Bumpers
p/n: 60-0104-24
This Clutch and Brake Pedal Bumper is designed from the original part for superior fitment and function. Pedal shank rides under floorboard. One and one-eighth (1-1/8") inch clearance for pedal shaft.
Taillight Mounting Pad
p/n: 60-0472-15
Pad, taillight bracket mounting. Two and three sixteenths (2-3/16) inch by three and three fourths (3-3/4) inch inside of bead.
Firewall Grommet
p/n: 40-0223-21
This Firewall Grommet can be used for a variety of applications since the grommet is plain (no holes). Designed from the original part for superior fit and seal.
Shock Absorber Link Bushings
p/n: 30-0226-33
A Rear Shock Absorber Upper Link Bushing pair designed from the original part for superior fitment and function. Rubber sleeve construction like original.
Starter Pedal Pad
p/n: 25-0049-89
Pad, starter pedal. Original pattern, brown rubber, exact copy.Height: .50 inches.
Gearshift Boot - Brown
p/n: 20-2166-26
This Gearshift Boot is designed from the original part for superior fitment and seal. This boot fits over the gearshift tower to make a weathertight connection for the transmission gearshift rod as it passes up through the vehicle floorboard.
Trunk Handle Grommet
p/n: 50-0183-87
Grommet, trunk handle bezel-thru-trunk lid. Special size, one (1) inch inside diameter.Buick 1937 Grommet, trunk handle bezel-thru-trunk lid.
Antenna Mount Pad
p/n: 50-0305-21
Mounting pad, running board antenna. Use in conjunction with our # 50-0280-21. Length: 1.75 inches. Width: 1.75 inches. Height: 2.0 inches.
1-7/16" Firewall Grommet
p/n: 40-0204-21
This Firewall Grommet is used to run the wiring harness through the firewall. Designed from the original part for superior fit and seal.
2-1/4" Firewall Grommet
p/n: 50-0166-20
This Firewall Grommet is used to run the wiring harness through the firewall mat. Designed from the original part for superior fit and seal.
Windshield Division Bar Gasket
p/n: 70-0098-52
This Windshield Division Bar Gasket is designed from the original part for superior fitment and seal. Part combines inner and outer gasket in one piece as original. For seventeen (17") inch to (20") inch lengths.
Shock Absorber Arm Bushing
p/n: 30-0192-32
Bushing, shock absorber arm. Restore proper shock action.Height: 1.375 inches.
Spring shackle bushing
p/n: 30-0090-32
Bushing, spring shackle, for shackle and eye leaf of rear spring. Eight (8) required per car.
Wiper Transmission Gasket
p/n: 50-0081-53
Gasket, windshield wiper transmission.Width: 2.5625 inches. Height: .8125 inches.
Lower Door Weatherstrips
p/n: 60-0047-73
This Lower Door Weatherstrip pair is designed from the original part for superior fitment and seal. Each 36" length weatherstrip fastens to the cab threshold.
Rear Spring Pad
p/n: 70-0191-32
Pad, rear spring insulator for two (2) inch wide springs. (see our number 70-0245-32 for two and one fourth (2-1/4) inch springs). Cloth reinforced. Four (4) per vehicle.
Fender Welting
p/n: 20-1591-44
This black Fender Welting is designed from the original part for superior fitment and seal. This welting material fits between the fenders and the vehicle body. Eight (8) foot length.
Rear Window Gasket
p/n: 20-0394-81
This Rear Window Gasket is made just like the original and mounts around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Firewall Grommet
p/n: 60-0013-20
This Firewall Grommet is used to run the wiring harness and speedometer cable through the toe board. Designed from the original part for superior fit and seal.
Lower Door Weatherstrip Retainers
p/n: 20-0393-73
This Lower Door Weatherstrip Retainer pair is designed from the original part for superior fitment, finish and function. A pair of retainers for the lower door weatherstrips that mount on the left and right rocker sills. Does not include door weatherstrips.
Door Bumper
p/n: 17-0038-70
Wedge cushion, door dovetail. This is the rubber block which goes behind the dovetail receiving bumper or shoe.
Top Of Door Weatherstrips
p/n: 20-1646-73
This Top of Door Weatherstrip is designed from the original part for superior fitment, finish and function. One weatherstrip is enough for two doors. Cut to fit as needed for each upper door openings.
Firewall Grommet
p/n: 60-0010-45
This Firewall Grommet is the oblong four (4) hole style. The grommet fits the steel retainer for the throttle and choke cables, and the oil and temperature lines.