Firewall Grommet
p/n: 60-0013-20
This Firewall Grommet is used to run the wiring harness and speedometer cable through the toe board. Designed from the original part for superior fit and seal.
Brake and Clutch Pedal Bumpers
p/n: 60-0104-24
Bumpers, brake and clutch pedal shank, rides under floorboard. One and one eighth (1-1/8) inch clearance for pedal shaft. Compare with part 60-0579-24.
Starter Button
p/n: 60-0322-21
Starter button, push on replacement to rod. Two (2) inch outside diameter.
Starter Pedal Bellows
p/n: 60-0487-21
Bellows, starter pedal shaft-to-floorboard. One and three fourths (1-3/4) inch by two and one fourth (2-1/4) inch.Length: 2.25 inches. Width: 1.75 inches.
5" Wide Bow Drill Cloth Tape
p/n: 70-1175-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Battery Carrier Edge Liner
p/n: 60-0112-21
Edge liner, battery carrier cover.Length: 42.0 inches. Width: .25 inches. Height: .6875 inches.
Horn Button Contact Ring
p/n: 60-0157-21
Ring, horn button contact. Accessory banjo steering wheel. Four and one eighth (4-1/8) inch outside diameter.
Horn Button Contact Cushion
p/n: 60-0192-21
Cushion, standard steering wheel horn button contact. Two and one half (2-1/2) inch diameter.
Brake and Clutch Pedal Bumper
p/n: 60-0024-24
Bumpers, brake and clutch pedal shank to floorboard. Rides pedal shank under floorboard.
Cowl vent weatherstrip
p/n: 70-0143-54
Gasket, cowl vent. Perfect copy of original, not a sponge substitute, top quality material.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Rumble Seat Lid Corner Pad
p/n: 70-0152-87
Pads, rumble seat lid corners, original rounded triangle shape.Length: 1.5 inches. Width: .4375 inches.
Fuel Neck Grommet
p/n: 60-0040-41
Grommet, fuel filler neck. Fully molded rubber, slightly angled with retaining flange. Three and five sixteenths inch (3-5/16") outside width by three and one half inch (3-1/2") outside length by two and one eighth inch (2-1/8") inside hole diameter.
Front Bumper Seal
p/n: 70-1103-28
Seals, front bumper. Fully molded rubber, U-shaped. Three and one half inches (3-1/2") long by three and one half inches (3-1/2") wide by thirteen sixteenths inch (13/16") height. For the grommets see our #70-1104-28, sold separately.
Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Accelerator Rod Seal
p/n: 60-0136-41
Grommet, accelerator rod through toe board. Brass core and center bushing as original.
Fender Welting 1/4" Bead - 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty-five (25) foot roll. Typically used to attach two (2) fenders to body.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.