This windshield gasket set contains two (2) seals that mount around the perimeter's of both pieces of glass. It also has properly molded corners for a precise, factory fit.
Pads, quarter to top bow.
Convertible Hinge Pillar Weatherstrip - Attaches to the body and seals between the windshield post and the front section of the door or vent window frame when the door is closed. Includes special molded foot. Fits one (1) inch wide channel.
This Body To Frame Webbing is designed from the original part for superior fitment and function. This webbing is used to shim the body to the frame. Also used as an anti-squeak material. Webbing is two (2") inch wide, twenty-five (25') foot long roll.
Grommets, front bumper arm.
Bumper kit, hood.
Grommets, rear bumper arm.
Boot, floor mounted gear shift. Black.Width: 4.0 inches. Height: 5.0 inches.
Convertible Hinge Pillar Weatherstrip - Attaches to the body and seals between the A-pillar post and the front section of the door or vent window frame when the door is closed. Includes special molded foot. Fits three fourths (3/4) inch wide channel.
Window felt inner and/or outer. Flexible, pile lined, rubber covered, with black bead. Available in 3ft pair.
Seals, front of door.
This trunk/rumbleseat weatherstrip set is designed from the original parts for superior fitment and seal. The set includes the strip that mounts to the body and the strip that mounts to the lid.
This black Fender Welting is designed from the original part for superior fitment and seal. This welting material fits between the fenders and the vehicle body. Thirty (30) foot roll.
Kit, motor mount. Enough for one motor mount. Kit includes one (1) each of 78-6029-A, B-6038-C, 78-6048-A, B-6039-A, and B-6047.
Bumpers, convertible header bow. Four (4) piece set.
Gasket, cowl vent.
Brake and Clutch Pedal Pad pair. Molded on metal like original. Exact pyramid design. 1937-1940 Ford Trucks.
This Gearshift Boot is designed from the original part for superior fitment and seal. This boot fits over the gearshift tower to make a weathertight connection for the transmission gearshift rod as it passes up through the vehicle floorboard.
Pedal, accelerator. Original type.
Pads, fuel tank to frame.
This black Fender Welting is designed from the original part for superior fitment and seal. This welting material fits between the fenders and the vehicle body. Eight (8) foot length.
Hose, fuel tank to filler neck connecting.
Axle Rebound Pad - Suspension bumper for front axle.
Bumper, rear axle.
This Channel Filler Weatherstrip is designed from the original part for superior fitment and seal. This door glass to body filler seal fits in the metal channel that holds the glass piece. Sold in a 36" strips.
Seal, lower door.
Seal, transmission cover to top of transmission.
Kit, hood to cowl weatherstrip. Forty-nine inch (49") extruded rubber strip includes installation screws.
Pads, trunk hinge.
Seal, door glass and stainless frame special. Top, bottom, and sides for one door.Width: .375 inches. Height: .625 inches.
Stops, rumble lid. Lower. Installs on floor.
Pads, taillight stand. Rubber with bead.
This Door Check Link Rod End Stop is designed from the original part for superior fit and function. This door stop fits between the door and body to limit the swing opening of the door preventing overtravel. Door check arm and bumper. Enough for one door.
Seal, header bow.
Seal, transmission cover to floor.
Seals, tie rod end. Four (4) piece set.
Seal, headlight bucket to fender.
Grommet, cowl wiring firewall.
Grommet, fuel filler neck. Fully molded rubber with small retaining lip. Three and five eighths inch (3-5/8") outside diameter by two and nine sixteenths inch (2-9/16") inside hole diameter.
Pads, upper hood hinge.
This Front or Rear Upper Motor Mount reproduction is designed from the original part for superior fitment and durability. This mount fits between the engine and chassis to support the engine and reduce harmonic vibrations.
Seal, top iron to door glass. One (1) inch wide by thirty (30) inch length.
Pads, taillight stand. Rubber WITHOUT bead. Original type.
Pads, wiper stand. Replaces factory #78-17556.
Mount, front motor. Lower.Ford Truck 1932-47: All Ford Trucks, 2 each required. 1948-51: Ford F100 Series both 6 or 8 cylinder, 1 each required.
This Convertible Roof Rail Weatherstrip is designed from the original part for superior fitment and seal. This window channel seal fits between windshield posts and door. Also fits along the top irons. This part is one (1) each. Five (5) individual pieces are required for the complete top.
Seals, taillight lens to bucket.
Pad, trunk lid handle.
Gasket, rear license plate lamp lens.
Bumper, door jam.Qty Required:2 Two (2) required per car.