Vibration damper, crankshaft, front. Revulcanizing service for rubber cushion elements.
Bushing and pin assembly cartridge. Inlox type, front wheel lower support arm inner pin. Shipped with instructions for reinstalling.Length: 5.75 inches.
Bumper, front suspension (inside of coil spring). Made with three five sixteenths (5/16) inch studs as original.
Bushing assembly, front wheel support; upper and outer. Inlox type cartridge bushing assembly.
Strap, door check. T-type, special heavy duty construction of rubber with multiple ply webbing and molded-in steel crossbar. Full length as original with one eighth (1/8) inch by seven eighths (7/8) inch steel crossbar.
This Windshield Gasket mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Guard strip, hood to cowl. Brass core with molded integral hood rest.Length: 14.875 inches.
This Revulcanization Service Only is designed to restore your Rear Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
This windshield gasket weatherstrip comes in a ten foot (10') strip and mounts around the full perimeter of the front glass. It has the slot to accommodate the outer edge's decorative molding and the ends may require trimming and bonding for installation.
Pads, hood front corners. Large self prong type with metal core molded left and right.Length: 3.375 inches.
Bushings, front suspension torque arm. Necessary for proper front end geometry.
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. Made with a metal core. This pad acts as the headlight adjusting collar.
Bumpers, front spring. One (1) pair required per car.
This Revulcanization Service Only is designed to restore your Engine Mount Stabilizer Bracket to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Pads, rear axle rebound.Length: 5.125 inches. Width: 1.4375 inches.
Grommets, rear bumper. Fully molded rubber. Three and five eighths inch (3-5/8") outside diameter by one and nine sixteenths inch (1-9/16") inside hole length by three eighths inch (3/8") inside hole width by one and one half inch (1-1/2") height.
Liners, front fender to running board. Reversible right and left like original. Length: 15.0 inches.
Grommets, rear bumper.Length: 3.625 inches. Width: 3.3125 inches.
Liner, running board to body, (side apron to body seal). Set consists of two (2) pieces seven (7) foot long. One (1) inch width is after fold over.
Grommets, front bumper. Molded right and left with correct detail as originally found. Fully molded rubber. Four inches (4") outside length by three inches (3") outside width by one and nine sixteenths inch (1-9/16") inside hole length by one half inch (1
Channel, rigid run, for vent window division bar. Chrome beaded edge, mohair lined steel channel to proper dimensions for window side of wing window frame.
Bearings, stabilizer front rod. Requires two (2) per car. Fully molded rubber. Two and one fourth inch (2 1/4") length by one and thirteen sixteenths inch (1 13/16") width by nine sixteenths inch (9/16") inside hole diameter by two and one eighths inch (2
Seal, gearshift to floorboard.Length: 5.625 inches. Width: 4.875 inches.
Grommet, rear spare wheel carrier bracket. Two (2) per car. (Also order our #32-0355-37 separately).
Grommet, steering column.Length: 5.625 inches.
This Engine Mount Pad pair is used as a support at the timing gear cover. One (1) pair required per car. Sold only in pairs.
Pads, headlight bracket mounting to fender. Molded left and right. Proper construction with beading as original. Sold in complete pairs only.Length: 9.
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Grommets, sidemount to fender.
Pads, taillight bracket mounting, with proper beading.Length: 6.625 inches.
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0188-22.Length: 3.875 inches. Width: 2.875 inches.
Pads, brake and clutch pedal, slip over type. Black rubber only. For black and red (semi-automatic clutch models) see our #30-0188-89.Length: 3.875 inches.
Gaskets, headlight lens and reflector mounting. A three sixteenths (3/16) inch cross section rubber ring of proper diameter.
Pads, rumbleseat step.
Grommet, fuel filler neck to fender.
Pads, trunk hinge. Four (4) piece set.
Grommet, firewall, for ignition cable and thermometer tube. For two and one half (2-1/2) inch hole in sheet metal.
This Engine Mount pair is used as the engine crank case link ball insulator. Correctly designed with careful attention to detail as original. Sold only in pairs.
Channel, flexible window run, un-beaded. Cloth covered mohair-lined type. Available in 6ft lengths.
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
This Beltline Weatherstrip is sold as a three (3) foot pair. The beltline is used for side window inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Gasket, cowl vent. Top quality sponge of correct section, cut to sufficient length for circumference of vent cover.
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Bumper, inner hood rest. Good copy and material. One (1) pair required per car.Length: 1.50 inches. Width: .875 inches.
Cloth covered mohair-lined type. For sides and top of side windows. Available in 5ft lengths.
Seals, brake and clutch pedal shanks, against underside of floorboard.Length: 2.5625 inches. Width: 1.75 inches.