Please click on the part name in red in order to get a complete description.
Pad kit, body to frame. Thirty-four (34) piece set. Includes installation instructions.
Webbing, body to frame. Two (2) inch wide, twenty five (25) foot long roll.
Channel, door glass flexible run. Fabric covered bead. Sixty (60) inches long. Measures 9/16” tall x 5/8” wide. Used with 1/4” glass.
Grommets, front bumper arm.
Grommets, rear bumper arm.
Boot, floor mounted gear shift. Black.Width: 4.0 inches. Height: 5.0 inches.
Bumper kit, hood. Standard.
Window felt inner and/or outer. One (1) pair of three (3) foot lengths. Flexible, pile lined, rubber covered, with black bead. For front door, rear door and quarter windows.
This front door weatherstrip pair is designed from the original parts for superior fitment and seal. These door seals mount directly to the body to seal against the full perimeter of both the front left and front right doors.
Seals, quarter window. Ends pre-bonded together.
Windshield weatherstrip gasket seal. Fully molded rubber channel for installing front window glass. Seals windshield glass to body and protects interior of vehicle. All corners are correctly molded to fit perfectly. Exact reproduction of original sea
Fender welting. Thirty (30) foot roll. Black, textured finish. 1/4" bead.
Kit, motor mount. Enough for one motor mount. Kit includes one (1) each of 78-6029-A, B-6038-C, 78-6048-A, B-6039-A, and B-6047.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Pad, trunk handle base to trunk.
Gasket, cowl vent.
Pads, brake and clutch pedal. Molded on metal like original. Exact pyramid design.Ford Truck 1937-40 Pads, pedal.
Boot, gear shift. Taupe.
Pedal, accelerator. Original type.
Pads, fuel tank to frame.
Fender welting. Eight (8) foot length.
Weatherstrips, top of door. Mounts on body from approximately just above the hinge to near the beltline on the lock side of the car. Each door opening strip is made from top quality closed cell sponge rubber approximately 54 inches long.
Hose, fuel tank to filler neck connecting.
Bumper, rear axle.
Axle Rebound Pad - Suspension bumper for front axle.
Seal, door glass to body. Fits in metal channel that holds glass. Also functions as the door to window seal when window is rolled up. Sold in a 36 inch strip.
Seal, transmission cover to top of transmission.
Kit, hood to cowl weatherstrip. Forty-nine inch (49") extruded rubber strip includes installation screws.
Stops, rumble lid. Lower. Installs on floor.
Grommets, dash. Black.Ford Truck 1940 Grommets, dash. Black. Ford Cars 1938-40 Grommets, choke and throttle dash. Replacement rubber type.
Pads, taillight bucket
Seal, transmission cover to floor.
Kit, door check arm and bumper. Enough for one door.
Seal, lower door.
Seals, tie rod end. Four (4) piece set.
Seal, headlight bucket to fender.
Pads, outside door handle.
Grommet, cowl wiring firewall.
Grommet, fuel filler neck. Fully molded rubber with small retaining lip. Three and five eighths inch (3 5/8") outside diameter by two and nine sixteenths inch (2 9/16") inside hole diameter by three and three sixteenths (3 3/16") sheet metal hole/retainin
Pads, upper hood hinge.
Grommets, horn bell to bracket.
Front or rear upper motor mount. Useage: Front motor mount for 1932-1947 Ford Trucks with 6 and 8 cylinders. Front motor mount for 1948-1951 Ford Trucks F-1, F-2, F-3. Two (2) required for trucks. Also used for 1932-1948: Ford & Mercury cars as a front
Pads, taillight bucket. Cork as original.
Mount, front motor. Lower.Ford Truck 1932-47: All Ford Trucks, 2 each required. 1948-51: Ford F100 Series both 6 or 8 cylinder, 1 each required.
Pads, door striker plate.
Seals, taillight lens to bucket.
Seal, wiper pivot shaft to roof or cowl. Small type. Replaces factory #11A-17541. Note: this part is used as a wiper pivot shaft to roof in 1937-1939. It is used as a wiper pivot shaft to cowl in 1941-1948.
Pad, rear license plate bracket. Cork.
Pads, outside door handle. Paper as original.
Bumper, door jam.Qty Required:2 Two (2) required per car.
Pad, hood ornament base. Paper. Deluxe.
Pad, hood ornament base. Paper. Standard.
Pads, radiator to frame.
Pad, trunk handle base to handle.
Gasket, trunk handle license plate light lens.
Grommet, choke and throttle rod or hood pull cable firewall.1932-47: All Trucks for choke & throttle rod; 1957-63: All Trucks for choke & wiper.
Bumpers, glovebox door.Ford Cars 1960 Bumpers, fuel tank door. All Galaxie models. Ford Truck 1935-47 Bumpers, glovebox door.
Bumper, door check arm.