Please click on the part name in red in order to get a complete description.
This windshield gasket set contains two (2) seals that mount around the perimeter's of both pieces of glass. It also has properly molded corners for a precise, factory fit.
Pads, center pillar post. Two (2) upper and two (2) lower in set.
Pads, quarter to top bow.
Convertible Hinge Pillar Weatherstrip - Attaches to the body and seals between the windshield post and the front section of the door or vent window frame when the door is closed. Includes special molded foot. Fits one (1) inch wide channel.
Webbing, body to frame. Two (2) inch wide, twenty five (25) foot long roll.
Grommets, front bumper arm.
Grommets, rear bumper arm. Fully molded rubber. Five and one half inch (5-1/2") outside length by two and thirteen sixteenths inch (2-13/16") outside width by one and one half inch (1-1/2") inside hole length by three eighths inch (3/8") inside hole width
Grommets, rear bumper arm.
Boot, floor mounted gear shift. Black.Width: 4.0 inches. Height: 5.0 inches.
Bumper kit, hood. Standard.
Pad, convertible top resting block. Used when top is down. One (1) required per vehicle.
Convertible Hinge Pillar Weatherstrip - Attaches to the body and seals between the A-pillar post and the front section of the door or vent window frame when the door is closed. Includes special molded foot. Fits three fourths (3/4) inch wide channel.
Window felt inner and/or outer. One (1) pair of three (3) foot lengths. Flexible, pile lined, rubber covered, with black bead. For front door, rear door and quarter windows.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Seals, front of door.
Seal, lower door.
Fender welting. Thirty (30) foot roll. Black, textured finish. 1/4" bead.
Kit, motor mount. Enough for one motor mount. Kit includes one (1) each of 78-6029-A, B-6038-C, 78-6048-A, B-6039-A, and B-6047.
Bumpers, convertible header bow. Four (4) piece set.
Pad, trunk handle base to trunk.
Gasket, cowl vent.
Pads, brake and clutch pedal. Molded on metal like original. Exact pyramid design.Ford Truck 1937-40 Pads, pedal.
Boot, gear shift. Taupe.
Pedal, accelerator. Original type.
Pads, fuel tank to frame.
Fender welting. Eight (8) foot length.
Hose, fuel tank to filler neck connecting.
Pads, trunk hinge.
Bumper, rear axle.
Axle Rebound Pad - Suspension bumper for front axle.
Seal, door glass to body. Fits in metal channel that holds glass. Also functions as the door to window seal when window is rolled up. Sold in a 36 inch strip.
Seal, transmission cover to top of transmission.
Kit, hood to cowl weatherstrip. Forty-nine inch (49") extruded rubber strip includes installation screws.
Seal, door glass and stainless frame special. Top, bottom, and sides for one door.Width: .375 inches. Height: .625 inches.
Grommets, dash. Black.Ford Truck 1940 Grommets, dash. Black. Ford Cars 1938-40 Grommets, choke and throttle dash. Replacement rubber type.
Pads, taillight bucket
Seal, header bow.
Seal, transmission cover to floor.
Kit, door check arm and bumper. Enough for one door.
Seals, tie rod end. Four (4) piece set.
Seal, headlight bucket to fender.
Pads, outside door handle.
Grommet, cowl wiring firewall.
Grommet, fuel filler neck. Fully molded rubber with small retaining lip. Three and five eighths inch (3 5/8") outside diameter by two and nine sixteenths inch (2 9/16") inside hole diameter by three and three sixteenths (3 3/16") sheet metal hole/retainin
Pads, upper hood hinge.
Grommets, horn bell to bracket.
Front or rear upper motor mount. Useage: Front motor mount for 1932-1947 Ford Trucks with 6 and 8 cylinders. Front motor mount for 1948-1951 Ford Trucks F-1, F-2, F-3. Two (2) required for trucks. Also used for 1932-1948: Ford & Mercury cars as a front
Seal, top iron to door glass. One (1) inch wide by thirty (30) inch length.
Pads, wiper stand. Replaces factory #78-17556.
Pads, taillight bucket. Cork as original.
Mount, front motor. Lower.Ford Truck 1932-47: All Ford Trucks, 2 each required. 1948-51: Ford F100 Series both 6 or 8 cylinder, 1 each required.
This Convertible Roof Rail Weatherstrip is designed from the original part for superior fitment and seal. This window channel seal fits between windshield posts and door. Also fits along the top irons. This part is one (1) each. Five (5) individual pieces are required for the complete top.
Bumper, door jam.
Seals, taillight lens to bucket.
Pad, rear license plate bracket. Cork.
Pads, outside door handle. Paper as original.
Bumper, door jam.Qty Required:2 Two (2) required per car.
Pad, hood ornament base. Paper. Standard.
Pad, hood ornament base. Paper. Deluxe.
Pads, radiator to frame.
Pad, trunk handle base to handle.
Gasket, trunk handle license plate light lens.
Grommet, choke and throttle rod or hood pull cable firewall.1932-47: All Trucks for choke & throttle rod; 1957-63: All Trucks for choke & wiper.
Bumpers, glovebox door.Ford Cars 1960 Bumpers, fuel tank door. All Galaxie models. Ford Truck 1935-47 Bumpers, glovebox door.
Bumper, door check arm.