Pad set, detachable center post, folding top upper and lower, right and left. Steel cores as original. 4 piece set.Width: 3.0 inches. Height: 2.75 inches.
Bushing and pin assembly cartridge. Inlox type, front wheel lower support arm inner pin. Shipped with instructions for reinstalling.Length: 5.75 inches.
Insulator assembly, rear engine support at transmission housing. Revulcanization service only.
This Windshield Gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit.
Bumper, front suspension (inside of coil spring). Made with three five sixteenths (5/16) inch studs as original.
This four (4) piece Front Door Vent Window Weatherstrips contain the upper and lower seals that cover the top, front, and bottom of the vent window. All of the pieces are designed from original parts for a precise, factory fit.
Bumper assembly, front suspension inside coil spring, with five sixteenths (5/16) inch threaded studs as found originally.
Bushing assembly, front wheel support; upper and outer. Inlox type cartridge bushing assembly.
Weatherstrip, side window. Fits metal channel. Rubber only. Twelve (12) foot strip.Length: 144.0 inches. Width: .75 inches.
Stabilizer, fore and aft transmission to frame. A factory service part used to remedy clutch chatter. Steel core as original.Length: 7.50 inches.
Insulator, motor support, rear assembly. Revulcanization service only.
Bushings, front suspension torque arm. Necessary for proper front end geometry.
This Revulcanization Service Only is to restore your front or rear Door Lock Striker to it's like new original condition. Service requires your old metal striker core. Please call or email for more service details and ordering.
Bumper assembly, front spring rebound (upper arm). Steel core, with treaded stud just like original.
Pad, convertible top right and left latches.Width: 3.0 inches. Height: 2.50 inches.
Pads, hood front corners, large type. Molded right and left with metal cores and double tab retainers.Length: 3.1875 inches. Width: 2.125 inches.
Weatherstrip, door edge. Retained by metal clips. (For clips, see our #70-0391-73). Fifteen (15) feet per strip.
Bumper, rear frame to axle rubber. Two (2) per car.Length: 5.1875 inches. Width: 2.0625 inches.
Boot, gearshift cover. For cane shifts only.Length: 4.0 inches. Width: 3.0 inches. Height: 5.125 inches.
Pads, hood rear corners. High quality rubber with metal core as original.Length: 3.4375 inches. Width: 1.875 inches.
Pedal, accelerator. Revulcanization service only. Includes new ball sockets as original, with correctly detailed tread pattern.Length: 9.625 inches.
Grommets, rear bumper.Length: 4.3125 inches. Width: 2.6875 inches.
Cushions, motor support, at timing gear cover. One (1) pair required per car. Sold only in pairs.
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Channel, rigid run, for division bar opposite vent windows.
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0188-22.Length: 3.875 inches. Width: 2.875 inches.
Grommets, front or rear bumper. On models without trunk racks. Two (2) pair used per car if needing both front and rear bumper grommets. Three and five eighths inch (3-5/8") outside length by two and one fourth inch (2-1/4") outside width by one and five eighths
Retainer, intermediate bearing. All models with two piece driveshafts.
Pads, brake and clutch pedal, slip over type. Black rubber only. For black and red (semi-automatic clutch models) see our #30-0188-89.Length: 3.875 inches.
Bumper, convertible top pillar.Width: 1.9375 inches.
Bumper assembly, front door hinge, upper, stop. Two (2) per car, steel core as original.Height: .6875 inches.
Gaskets, taillight mounting, with proper beading and shape as original. For all models with center license mounting.Length: 7.125 inches.
Gasket, cowl vent. Perfect reproduction, high quality, original configuration, not a sponge substitute.Length: 14.0 inches. Width: 5.75 inches.
Rubber grip, handbrake lever.Length: 4.125 inches.
Grommet instrument board cables through firewall. Oval type with masked hole for six (6) wires or cables. Necessary replacement for correct restoration.
Grommet, fuel filler neck.
Knob, gearshift (floor shift type).
This Beltline Weatherstrip is sold as a three (3) foot pair. The beltline is used for side window inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Filler, windshield division channel ends, upper and lower. Two (2) piece set.
Boot, brake and clutch pedal shank at toe board.Length: 2.9375 inches.
Grommet, steering column at toe board.
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Pad, convertible top center latch. Excellent workmanship with metal insert like originalWidth: 2.0 inches. Height: 1.1875 inches.
Bowdrill cloth tape is used for covering convertible side window weatherstrip. Available in a 5 ft roll.
Gaskets, taillight door lens. For cars without center license light. Two (2) strips eleven and one half (11-1/2) inches long each.Length: 11.5 inches.
Bushing, spring shackle. Six (6) per car. Packard's "self flanging" type.