Crankshaft Vibration Damper - Revulcanization Only
p/n: 30-0376-12
This Revulcanization Service Only is designed to restore the Crankshaft Vibration Damper to a like new original condition. This revulcanizing service is for the rubber cushion elements. Service requires your metal core.
Suspension bushing
p/n: 30-0385-36
Bushing and pin assembly, cartridge, Inlox type, front wheel lower support arm inner pin. Shipped with instructions for re-installing.Length: 5.75 inches.
Front Door Vent Window Weatherstrips
p/n: 30-0089-55
These Front Door Vent Window Weatherstrips are designed from the original parts for superior fitment and seal. The pieces are molded as left and right and are one piece with the division post seal.
Front spring bushing
p/n: 30-0391-32
Bushing assembly, front wheel support; upper and outer. Inlox type cartridge bushing assembly.
Fluted radiator hose
p/n: 30-0258-31
Hose, radiator, upper. Fluted outside diameter just like original.
Front suspension bumper
p/n: 30-0490-32
Bumper, front suspension (inside of coil spring). Made with three five sixteenths (5/16) inch studs as original.
Door check strap
p/n: 40-0535-70
Strap, door check. T-type, special heavy duty construction of rubber with multiple ply webbing and molded-in steel crossbar. Full length as original with one eighth (1/8) inch by seven eighths (7/8) inch steel crossbar.
Windshield Gasket
p/n: 30-0514-50
This Windshield Gasket mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation. It also has the slot to accommodate the outer edge's decorative molding.
Hood to cowl bumper
p/n: 30-0223-42
Bumpers, hood to cowl. Brass core, one and one half (1-1/2) inch by four and one half (4-1/2) inch.Length: 4.50 inches. Width: 1.50 inches.
Engine Mount Service – Revulcanization Only
p/n: 30-0185-11
This Revulcanization Service Only is designed to restore your Rear Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Windshield Gasket Weatherstrip
p/n: 30-0014-52
This windshield gasket weatherstrip comes in a ten foot (10') strip and mounts around the full perimeter of the front glass. It has the slot to accommodate the outer edge's decorative molding and the ends may require trimming and bonding for installation.
Front suspension bushing
p/n: 30-0239-32
Bushings, front suspension torque arm. Necessary for proper front end geometry.
Headlight Mounting Pad
p/n: 30-0134-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. Made with a metal core. This pad acts as the headlight adjusting collar.
Front suspension bumper
p/n: 30-0229-32
Bumper assembly, front suspension rebound (upper arm). Straight style with stud.
Engine Mount Service – Revulcanization Only
p/n: 30-0543-11
This Revulcanization Service Only is designed to restore your Engine Mount Stabilizer Bracket to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Rear bumper grommet
p/n: 30-0008-29
Grommets, rear bumper. Fully molded rubber. Three and five eighths inch (3-5/8") outside diameter by one and nine sixteenths inch (1-9/16") inside hole length by three eighths inch (3/8") inside hole width by one and one half inch (1-1/2") height.
Spare wheel mounting pad
p/n: 30-0480-37
Cushion, spare wheel in fenderwell.1937: 12's only (2 pair required). 1938-39: 12's only (3 pair required).Length: 12.875 inches. Width: 3.0 inches.
Axle rebound pad
p/n: 30-0371-32
Bumper, rear frame to axle rubber. Two (2) per car.Length: 5.1875 inches. Width: 2.0625 inches.
Door Weatherstrip
p/n: 30-0084-73
A high-quality Door Weatherstrip for the front or rear doors. Sold as an each this upgrade part has a hollow bulb weatherstrip construction rather than composite sponge and solid rubber. Held in by clips, (sold separately).
Rear bumper grommet
p/n: 30-0006-29
Grommets, rear bumper.Length: 3.625 inches. Width: 3.3125 inches.
Front bumper grommet
p/n: 30-0001-28
Grommet, front bumper. Molded right and left with hollow construction as found on original.Length: 4.0 inches. Width: 2.25 inches.
Running Board Edge Seal
p/n: 30-0169-44
Liner, running board to body, (side apron to body seal). Set consists of two (2) pieces seven (7) foot long. One (1) inch width is after fold over.
Brake vacuum cylinder rod boot
p/n: 30-0115-24
Boot, vacuum brake cylinder main rod. Accordion type, two (2) inches diameter by six (6) inches. Top quality workmanship and material.Length: 6.0 inches.
Hood corner pad
p/n: 30-0088-42
Pad, hood front corner. Metal core, retained by four (4) tabs.Length: 3.25 inches. Width: 1.25 inches.
Stabilizer bushing
p/n: 30-0483-33
Bearings, stabilizer rear rod. Requires two (2) per car. Fully molded rubber. Two and one fourth inch (2 1/4") length by one and thirteen sixteenths inch (1 13/16") width by eleven sixteenths inch (11/16") inside hole diameter by two and one eighths inch
Plug wire sleeve
p/n: 30-0204-21
Sleeve, plug wire tube to distributor cap. One (1) pair required per car.Height: .9375 inches.
Rigid Run Channel
p/n: 30-0180-57
Channel, rigid run, for vent window division bar. Chrome beaded edge, mohair lined steel channel to proper dimensions for window side of wing window frame.
Stabilizer bushing
p/n: 30-0484-33
Bearings, stabilizer front rod. Requires two (2) per car. Fully molded rubber. Two and one fourth inch (2 1/4") length by one and thirteen sixteenths inch (1 13/16") width by nine sixteenths inch (9/16") inside hole diameter by two and one eighths inch (2
Gearshift seal
p/n: 30-0165-24
Seal, gearshift to floorboard.Length: 5.625 inches. Width: 4.875 inches.
Spare wheel carrier grommet
p/n: 30-0334-37
Grommet, rear spare wheel carrier bracket. Two (2) per car. (Also order our #32-0355-37 separately).
Engine Mount Pad
p/n: 30-0331-11
This Engine Mount Pad pair is used as a support at the timing gear cover. One (1) pair required per car. Sold only in pairs.
Fender welting 1/4" bead 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Fender welting 50ft chrome
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Fender Welting with 3/16 Bead - 50 Ft. Roll
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Red brake and clutch pedal pad
p/n: 30-0188-89
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0188-22.Length: 3.875 inches. Width: 2.875 inches.
Prop shaft retainer bushing
p/n: 70-2268-27
Retainer, intermediate bearing. All models with two piece driveshafts.
Brake and clutch pedal pad
p/n: 30-0188-22
Pads, brake and clutch pedal, slip over type. Black rubber only. For black and red (semi-automatic clutch models) see our #30-0188-89.Length: 3.875 inches.
Taillight mounting pad
p/n: 30-0201-15
Pads, taillight bracket mounting, with proper beading and shape. For two and one eighths (2-1/8) inch by five and one half (5-1/2) inch base.Length: 5.
Headlight lens gasket
p/n: 30-0176-14
Gaskets, headlight lens and reflector mounting. A three sixteenths (3/16) inch cross section rubber ring of proper diameter.
Door Bumper
p/n: 34-0305-71
Bumper assembly, front door hinge, upper, stop. Two (2) per car, steel core as original.Height: .6875 inches.
Taillight mounting pad
p/n: 30-0318-15
Gaskets, taillight mounting, with proper beading and shape as original. For all models with center license mounting.Length: 7.125 inches.