7/8" Window Weatherstrip
p/n: 70-1192-52
This Window Weatherstrip is for models with chrome reveal molding. Available by the foot.
7/8" Windshield Weatherstrip
p/n: 70-1190-52
This Windshield Weatherstrip is for windows without chrome reveal molding. For a 2 piece windshield, select gasket for division bar. Available by the foot.
9/16" Channel filler weatherstrip
p/n: 70-0489-58
Weatherstrip, channel filler, door window sash channel and some quarter window sash channel. Special type with wide weatherstrip edge to be trimmed at assembly, when necessary. Available by the foot.
Control arm bushing seal
p/n: 60-0094-32
Seal, upper and lower control arm cross shaft bushing, at inner end of arm.1939-48: Lower only, all pass. (exc.
Spare Wheel Mounting Pad
p/n: 30-0446-37
Pad, spare tire inner.Length: .875 inches. Width: .75 inches.
Spring shackle seal
p/n: 70-1125-33
Washer, front and rear spring shackle, seal for shackle pin. Constructed of neoprene.
1/2" Door Weatherstrip
p/n: 70-0311-73
This Door Weatherstrip is designed to be an exact match to the original. The weatherstrip is made from a high-quality EPDM sponge rubber. Available by the foot.
Rear spring pad
p/n: 30-0370-32
Separator, spring leaf, rear. Use as required, up to twenty four (24) needed per car.
Steering Knuckle Support Seal
p/n: 50-0525-36
Seal, steering knuckle support, upper or lower. Die cut one fourth (1/4) inch, four (4) used per car.Height: .25 inches.
Wheel Cover Cushion
p/n: 70-0633-38
Filler, wheel cover to wheel. Approximately two and one eighth (2-1/8) inches long each, twenty (20) required per car. (Five (5) per wheel cover).
1/16" Sash Channel Filler - Cork
p/n: 70-1115-57
This 1/16" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
Tie rod dust cover
p/n: 10-0134-32
Rubber seal, tie rod ends and drag link ends. 2 or 4 required per car. Note: for 4 cylinder vehicles.
1/2" Trunk Weatherstrip
p/n: 70-1106-99
This Trunk Weatherstrip is made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
15/16" Wiring Grommet
p/n: 32-0165-15
This Wiring Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber. Designed to run the taillight wire through the trunk floor pan.
Engine Mount Washer
p/n: 20-0442-11
This Front Upper Engine Mount Washer is made of steel. The large upper engine mount insulator sits in this special washer. Fits all Ford 6 cylinder and Flathead V-8 models.
Run Channel Retaining Clip
p/n: 60-0374-58
This Run Channel Retaining Clip is designed from the original part for an authentic fit, finish and function. Clip fits at the end of door window run channel. Tempered spring steel.
Door Handle Gaskets
p/n: 20-2238-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. Manufactured from paper just as original.
Windshield Wiper Hose Grommet
p/n: 20-1611-20
This Windshield Wiper Hose Grommet is used to run the wiper hose through the firewall. Designed from original part so it fits correctly.
Wiper Hose Grommet
p/n: 20-2206-53
This Wiper Hose Grommet is used where the wiper hose and temperature gauge wire go through the firewall. The grommet can also be used where the headlight bucket wires go through the inner fender.