2-7/16" Firewall Grommet
p/n: 70-0621-20
This Firewall Grommet is used to run the cowl vent drain hose and throttle control cable through the firewall. Designed from the original part for superior fit and seal.
Exhaust System Hanger
p/n: 70-0626-13
Insulator (hanger) tailpipe to frame. See also our #70-0600-13.Length: 3.9375 inches. Width: 1.9375 inches.
Firewall Grommet
p/n: 70-1203-20
This Firewall Grommet is used to run various electrical and dash gauge wires through the firewall. Also see our 32-1201-20 and 32-0225-20.
Exhaust system hanger
p/n: 70-0220-13
Insulator, exhaust system. Double end threaded, for muffler pipe and intermediate pipe bracket on extra long body styles. Two (2) required per car.
Windshield Division Bar Gasket
p/n: 70-0098-52
This Windshield Division Bar Gasket is designed from the original part for superior fitment and seal. Part combines inner and outer gasket in one piece as original. For seventeen (17") inch to (20") inch lengths.
Rear Spring Pad
p/n: 70-0191-32
Pad, rear spring insulator for two (2) inch wide springs. (see our number 70-0245-32 for two and one fourth (2-1/4) inch springs). Cloth reinforced. Four (4) per vehicle.
Spare Tire Bumper
p/n: 70-0126-37
Rest pad, spare wheel cover, metal core, screw held type. Eight (8) required per car.Width: 1.75 inches. Height: 1.4375 inches.
Hood Rest Pad
p/n: 70-0150-42
Pad, hood rest, molded to brass core, screw mounted.Width: 1.75 inches.
Spare Tire Bumper
p/n: 70-0125-37
Rest pad, spare wheel cover, metal core, tab held type. Sixteen (16) required per car.Width: 1.75 inches. Height: .75 inches.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Door Handle Ferrule
p/n: 60-0389-69
Ferrule, outside door handle. Chrome with rubber sleeve. Two (2) piece set includes one (1) chrome piece and one (1) rubber piece. Enough for one door.
2" Firewall Grommet
p/n: 70-0158-21
This Firewall Grommet is used to run the ignition switch conduit through the firewall. Designed from original parts for excellent workmanship.
Body Mounting Pad
p/n: 70-0235-48
Pad, body mounting. Fully molded rubber with locating collar. Rectangular shaped.
Lower Suspension Arm Dust Seal
p/n: 70-0624-32
Dust seal, "O" ring. Lower suspension arm pin bushing. Four (4) required per car.Height: .25 inches.
Wiper Transmission Gasket
p/n: 70-1198-53
Gasket, windshield wiper transmission (1939-later type). Replaces #4097038.
Door Check Link Rod End Stop
p/n: 70-0326-70
End stop and pad, door check link rod. Rubber with embedded steel plate, five sixteenths (5/16) inch diameter thread. Most models with rod type door checks.
Wiper Transmission Gasket
p/n: 70-0499-53
Gasket, wiper transmission mounting. Replaces #4089635 for smaller type wiper gear, about 7/8" X 1-1/8". Early series models only.
Shock or Stabilizer Link Cross Pin Bushing
p/n: 50-0220-32
This Shock or Stabilizer Link Cross Pin Bushing is designed from the original part for superior fitment and function. A rubber bushing for shock absorber link cross pin or stabilizer cross link pin.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Electrical Terminal Boot
p/n: 30-0279-41
This Electrical Terminal Boot is designed from the original part for superior fitment and seal. This boot works to cover and protect electrical terminal connections.
Body Mounting Pad
p/n: 50-0131-48
Pad, body mounting. Fully molded rubber with locating collar. Two-inch (2") square by thirteen sixteenths inch (13/16") locating collar outside diameter by one half inch (1/2") locating collar inside diameter.
Shift Lever Grommet
p/n: 70-0769-26
Grommet, upper shift lever at steering column.Height: .25 inches.