Please click on the part name in red in order to get a complete description.
Covers, runningboard. Pre-molded.
This windshield gasket set contains two (2) seals that mount around the perimeter's of both pieces of glass. It also has properly molded corners for a precise, factory fit.
Pad kit, body to frame. Thirty-four (34) piece set. Includes installation instructions.
Webbing, body to frame. Two (2) inch wide, twenty five (25) foot long roll.
Grommets, dash. Original metal and rubber.Ford Truck 1940 Grommets, dash. Original metal and rubber. Replaces factory #91A-9719. Trucks.
Channel, door glass flexible run. Fabric covered bead. Sixty (60) inches long. Measures 9/16” tall x 5/8” wide. Used with 1/4” glass.
Grommets, front bumper arm.
Boot, floor mounted gear shift. Black.Width: 4.0 inches. Height: 5.0 inches.
Bumper kit, hood. Standard.
Window felt inner and/or outer. One (1) pair of three (3) foot lengths. Flexible, pile lined, rubber covered, with black bead. For front door, rear door and quarter windows.
Seal, lower door. Mounts to door scuff plates. Enough for 4 doors.
Seals, front of door.
This front door weatherstrip pair is designed from the original parts for superior fitment and seal. These door seals mount directly to the body to seal against the full perimeter of both the front left and front right doors.
Windshield weatherstrip gasket seal. Fully molded rubber channel for installing front window glass. Seals windshield glass to body and protects interior of vehicle. All corners are correctly molded to fit perfectly. Exact reproduction of original sea
Seal, lower door.
Fender welting. Thirty (30) foot roll. Black, textured finish. 1/4" bead.
Kit, motor mount. Enough for one motor mount. Kit includes one (1) each of 78-6029-A, B-6038-C, 78-6048-A, B-6039-A, and B-6047.
Bumper kit, hood. Deluxe.
Gasket, cowl vent.
Pads, brake and clutch pedal. Molded on metal like original. Exact pyramid design.Ford Truck 1937-40 Pads, pedal.
Boot, gear shift. Taupe.
Pedal, accelerator. Original type.
Pads, fuel tank to frame.
Bumper - Front Axle. Designed from original part so it fits correctly.
Fender welting. Eight (8) foot length.
Weatherstrips, top of door. One strip is enough for two doors. Cut to fit as needed for all four door upper door openings. Mounts on body from approximately directly above the hinge to near the beltline of the car for the front door opening, and from beltline to beltline for the rear door opening.
Hose, fuel tank to filler neck connecting.
Axle Rebound Pad - Suspension bumper for front axle.
Axle Rebound Pad - Suspension bumper for rear axle.
Seal, transmission cover to top of transmission.
Kit, hood to cowl weatherstrip. Forty-nine inch (49") extruded rubber strip includes installation screws.
Seals, brake and clutch pedal arms to floor board.
Grommets, dash. Black.Ford Truck 1940 Grommets, dash. Black. Ford Cars 1938-40 Grommets, choke and throttle dash. Replacement rubber type.
Pads, taillight bucket
Seal, transmission cover to floor.
Kit, door check arm and bumper. Enough for one door.
Seals, tie rod end. Four (4) piece set.
Seal, headlight bucket to fender.
Grommets, emergency brake cable to radius rod bracket.
Pads, outside door handle.
Grommet, cowl wiring firewall.
Grommet, fuel filler neck. Fully molded rubber with small retaining lip. Three and five eighths inch (3 5/8") outside diameter by two and nine sixteenths inch (2 9/16") inside hole diameter by three and three sixteenths (3 3/16") sheet metal hole/retainin
Pads, upper hood hinge.
Grommets, horn bell to bracket.
Front or rear upper motor mount. Useage: Front motor mount for 1932-1947 Ford Trucks with 6 and 8 cylinders. Front motor mount for 1948-1951 Ford Trucks F-1, F-2, F-3. Two (2) required for trucks. Also used for 1932-1948: Ford & Mercury cars as a front
Pads, wiper stand. Replaces factory #78-17556.
Pads, taillight bucket. Cork as original.
Mount, front motor. Lower.Ford Truck 1932-47: All Ford Trucks, 2 each required. 1948-51: Ford F100 Series both 6 or 8 cylinder, 1 each required.
Grommet, emergency brake cable to frame.
Bumper, door jam.
Seals, taillight lens to bucket.
Seal, wiper pivot shaft to roof or cowl. Small type. Replaces factory #11A-17541. Note: this part is used as a wiper pivot shaft to roof in 1937-1939. It is used as a wiper pivot shaft to cowl in 1941-1948.
Pad, rear license plate bracket. Cork.
Pads, outside door handle. Paper as original.
Grommet, wiper hose and heat tube firewall. Replaces factory #91A-17545.
Bumper, door jam.Qty Required:2 Two (2) required per car.
Pads, radiator to frame.
Gasket, trunk handle license plate light lens.
Grommet, choke and throttle rod or hood pull cable firewall.1932-47: All Trucks for choke & throttle rod; 1957-63: All Trucks for choke & wiper.
Bumpers, glovebox door.Ford Cars 1960 Bumpers, fuel tank door. All Galaxie models. Ford Truck 1935-47 Bumpers, glovebox door.
Bumper, door check arm.
Washer, rear fender. Large type. One and one half (1-1/2) inch diameter.
Washer, front fender. Small type. One and one fourth (1-1/4) inch diameter.