This windshield gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
This Body To Frame Webbing is designed from the original part for superior fitment and function. This webbing is used to shim the body to the frame. Also used as an anti-squeak material. Webbing is two (2") inch wide, twenty-five (25') foot long roll.
Grommets, dash. Original metal and rubber.Ford Truck 1940 Grommets, dash. Original metal and rubber. Replaces factory #91A-9719. Trucks.
Grommets, front bumper arm. Fully molded rubber. Three and three fourths inch (3-3/4") outside length by two and five eighths inch (2-5/8") outside width. One and three fourths inch (1-3/4") inside hole lengths by one fourth inch (1/4") inside hole widths
Boot, floor mounted gear shift. Black.Width: 4.0 inches. Height: 5.0 inches.
This black Fender Welting is designed from the original part for superior fitment and seal. This welting material fits between the fenders and the vehicle body. Thirty (30) foot roll.
Kit, motor mount. Enough for one motor mount. Kit includes one (1) each of 78-6029-A, B-6038-C, 78-6048-A, B-6039-A, and B-6047.
Bumpers, convertible header bow. Four (4) piece set.
Bumper kit, hood. Deluxe.
Gasket, cowl vent.
Brake and Clutch Pedal Pad pair. Molded on metal like original. Exact pyramid design. 1937-1940 Ford Trucks.
This Gearshift Boot is designed from the original part for superior fitment and seal. This boot fits over the gearshift tower to make a weathertight connection for the transmission gearshift rod as it passes up through the vehicle floorboard.
Pedal, accelerator. Original type.
Pads, fuel tank to frame.
Bumper - Front Axle. Designed from original part so it fits correctly.
Kit, cowl lacing. Includes mounting screws.
This black Fender Welting is designed from the original part for superior fitment and seal. This welting material fits between the fenders and the vehicle body. Eight (8) foot length.
Hose, fuel tank to filler neck connecting.
Axle Rebound Pad - Suspension bumper for front axle.
Axle Rebound Pad - Suspension bumper for rear axle.
Seal, transmission cover to top of transmission.
Seal, door glass and stainless frame special. Top, bottom, and sides for one door.Width: .375 inches. Height: .625 inches.
Seals, brake and clutch pedal arms to floor board.
Pads, outside door handle.
Grommets, dash. Black.Ford Truck 1940 Grommets, dash. Black. Ford Cars 1938-40 Grommets, choke and throttle dash. Replacement rubber type.
This Door Check Link Rod End Stop is designed from the original part for superior fit and function. This door stop fits between the door and body to limit the swing opening of the door preventing overtravel. Door check arm and bumper. Enough for one door.
Seal, transmission cover to floor.
Grommets, emergency brake cable to radius rod bracket.
Grommet, cowl wiring firewall.
Grommet, fuel filler neck. Fully molded rubber with small retaining lip. Three and five eighths inch (3-5/8") outside diameter by two and nine sixteenths inch (2-9/16") inside hole diameter.
Pads, upper hood hinge.
Grommets, horn bell to bracket.
This Front or Rear Upper Motor Mount reproduction is designed from the original part for superior fitment and durability. This mount fits between the engine and chassis to support the engine and reduce harmonic vibrations.
Seal, top iron to door glass. One (1) inch wide by thirty (30) inch length.
Pad, trunk handle base to trunk.
Mount, front motor. Lower.Ford Truck 1932-47: All Ford Trucks, 2 each required. 1948-51: Ford F100 Series both 6 or 8 cylinder, 1 each required.
Seal, headlight bucket to fender. Deluxe type.
This Convertible Roof Rail Weatherstrip is designed from the original part for superior fitment and seal. This window channel seal fits between windshield posts and door. Also fits along the top irons. This part is one (1) each. Five (5) individual pieces are required for the complete top.
Grommet, emergency brake cable to frame.
Pad, rear license plate bracket. Cork.
Bumper, door jam.Qty Required:2 Two (2) required per car.
Pads, radiator to frame.
Seal, trunk handle license plate light lens.
Grommet, choke and throttle rod or hood pull cable firewall.1932-47: All Trucks for choke & throttle rod; 1957-63: All Trucks for choke & wiper.
Bumpers, glovebox door.Ford Cars 1960 Bumpers, fuel tank door. All Galaxie models. Ford Truck 1935-47 Bumpers, glovebox door.
Washer, front fender. Small type. One and one fourth (1-1/4) inch diameter.
Washer, rear fender. Large type. One and one half (1-1/2) inch diameter.