Vibration damper, crankshaft, front. Revulcanizing service for rubber cushion elements.
Pad set, detachable center post, folding top upper and lower, right and left. Steel cores as original. 4 piece set.Width: 3.0 inches. Height: 2.75 inches.
Bushing and pin assembly, cartridge, Inlox type, front wheel lower support arm inner pin. Shipped with instructions for re-installing.Length: 5.75 inches.
This front door vent window weatherstrip kit is a six (6) piece set that contains the upper and lower seals that cover the top, front, and bottom of the vent window as well as the division post seals. All of the pieces are designed from original parts for
This front door vent window weatherstrip set is a four (4) piece set that contains the upper and lower seals that cover the top, front, and bottom of the vent window. All of the pieces are designed from original parts for a precise, factory fit.
Bushing assembly, front wheel support; upper and outer. Inlox type cartridge bushing assembly.
Hose, radiator, upper. Fluted outside diameter just like original.
Strap, door check. T-type, special heavy duty construction of rubber with multiple ply webbing and molded-in steel crossbar. Full length as original with one eighth (1/8) inch by seven eighths (7/8) inch steel crossbar.
Bumper, front suspension (inside of coil spring). Made with three eighths (3/8) inch stud as original.
This windshield gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation. It also has the slot to accommodate the outer edge's decorative molding.
Weatherstrip, side window. Fits metal channel. Rubber only. Twelve (12) foot strip.Length: 144.0 inches. Width: .75 inches.
Pads, lower, top removable center pillar, right and left. Brass core.Width: 3.375 inches. Height: 2.75 inches.
Pads, convertible top folding pillar (top main bow hinge), right and left, with brass core.Width: 2.75 inches.
Bumpers, hood to cowl. Brass core, one and one half (1-1/2) inch by four and one half (4-1/2) inch.Length: 4.50 inches. Width: 1.50 inches.
Insulator, motor support, rear assembly. Revulcanization service only.
This windshield gasket weatherstrip comes in a ten foot (10') strip and mounts around the full perimeter of the front glass. It has the slot to accommodate the outer edge's decorative molding and the ends may require trimming and bonding for installation.
Weatherstrip, convertible top to side windows. Fifteen sixteenths (15/16) inch by five eighths (5/8) inch. Sold in twelve (12) foot strips only.
Bushings, front suspension torque arm. Necessary for proper front end geometry.
Bumper assembly, front suspension rebound (upper arm). Straight style with stud.
Insulator assembly, transmission support. Revulcanization service only. Send in your old core for service.
Motor mount stabilizer bracket. Revulcanization service. Send in core and allow three weeks for service.
Grommets, rear bumper. Fully molded rubber. Three and five eighths inch (3-5/8") outside diameter by one and nine sixteenths inch (1-9/16") inside hole length by three eighths inch (3/8") inside hole width by one and one half inch (1-1/2") height.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Cushion, spare wheel in fenderwell.1937: 12's only (2 pair required). 1938-39: 12's only (3 pair required).Length: 12.875 inches. Width: 3.0 inches.
Bumper, rear frame to axle rubber. Two (2) per car.Length: 5.1875 inches. Width: 2.0625 inches.
Grommets, rear bumper.Length: 3.625 inches. Width: 3.3125 inches.
Gasket, windshield glass center division. Molded with screw holes and end pilots. Replaces #236866.
Grommet, front bumper. Molded right and left with hollow construction as found on original.Length: 4.0 inches. Width: 2.25 inches.
Pad, hood rear corner. Molded left and right with a metal core.Length: 2.50 inches. Width: 1.75 inches.
Liner, runningboard to body, (side apron to body seal). Set consists of two (2) pieces seven (7) foot long. One (1) inch width is after fold over.
Boot, vacuum brake cylinder main rod. Accordion type, two (2) inches diameter by six (6) inches. Top quality workmanship and material.Length: 6.0 inches.
Insulator, front coil spring. Four (4) piece set.
Boot vacuum clutch cylinder rod.Length: 4.0 inches.
Pad, hood front corner. Metal core, retained by four (4) tabs.Length: 3.25 inches. Width: 1.25 inches.
Bearings, stabilizer rear rod. Requires two (2) per car. Fully molded rubber. Two and one fourth inch (2 1/4") length by one and thirteen sixteenths inch (1 13/16") width by eleven sixteenths inch (11/16") inside hole diameter by two and one eighths inch
Sleeve, plug wire tube to distributor cap. One (1) pair required per car.Height: .9375 inches.
Channel, rigid run, for vent window division bar. Chrome beaded edge, mohair lined steel channel to proper dimensions for window side of wing window frame.
Bearings, stabilizer front rod. Requires two (2) per car. Fully molded rubber. Two and one fourth inch (2 1/4") length by one and thirteen sixteenths inch (1 13/16") width by nine sixteenths inch (9/16") inside hole diameter by two and one eighths inch (2
Seal, gearshift to floorboard.Length: 5.625 inches. Width: 4.875 inches.
Grommet, rear spare wheel carrier bracket. Two (2) per car. (Also order our #32-0355-37 separately).
Grommet, steering column.Length: 5.625 inches.
Bushing, front motor support at timing gear cover. One (1) pair required per car. Sold only in pairs.
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty fi
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0188-22.Length: 3.875 inches. Width: 2.875 inches.
Pad, convertible top removable center pillar.Length: 3.0625 inches. Width: 2.1875 inches.
Retainer, intermediate bearing. All models with two piece driveshafts.
Pads, brake and clutch pedal, slip over type. Black rubber only. For black and red (semi-automatic clutch models) see our #30-0188-89.Length: 3.875 inches.
Bumper, convertible top pillar.Width: 1.9375 inches.