Search Results
Please click on the part name in red in order to get a complete description.
Spring shackle bushing
p/n: 30-0420-32
Bushing, spring shackle. Six (6) per car. Packard's "self flanging" type.
Starter pedal pad
p/n: 25-0049-89
Pad, starter pedal. Original pattern, brown rubber, exact copy.Height: .50 inches.
Trunk handle grommet
p/n: 50-0183-87
Grommet, trunk handle bezel-thru-trunk lid. Special size, one (1) inch inside diameter.Buick 1937 Grommet, trunk handle bezel-thru-trunk lid.
Battery carrier edge liner
p/n: 27-0091-21
Seal strip, battery to fender apron. Two (2) correct cross section strips nineteen (19) inches long.
Bumper - Front Axle
p/n: 20-2175-33
Bumper - Front Axle. Designed from original part so it fits correctly.
Exhaust system hanger
p/n: 70-0631-27
Insulator, exhaust system, muffler pipe bracket. Also intermediate pipe bracket on extra-long body styles. Two (2) required per car, most models.
Firewall grommet
p/n: 50-0166-20
Grommet, wire harness-thru-firewall mat. Two (2) inch diameter with two and one fourth (2-1/4) inch outside diameter flange.
Windshield division bar gasket
p/n: 70-0098-52
Gasket, divided windshield center post. Combines inner and outer gasket in one piece as original. Seventeen (17) inch to (20) inch lengths.Length: 20.
Door check link rod end stop
p/n: 70-0479-70
End nut, check link (rubber bar with steel bar insert). Three fourths (3/4) inch by three fourths (3/4) inch by two (2) inch threaded five sixteenths (5/16) inch. (For round stop nut, see our #70-0326-70).
License light mounting pad
p/n: 40-0357-17
Pad, mounting, license light to body. A un-beaded pad as original with accurate outline and hole pattern.Length: 6.50 inches.
Door weatherstrip
p/n: 60-0047-73
Weatherstrip, lower door. Fastens to cab threshold. Two strips thirty six (36) inch long each.Length: 36.0 inches. Width: .4375 inches.
Rear Spring Pad
p/n: 70-0191-32
Pad, rear spring insulator for two (2) inch wide springs. (see our number 70-0245-32 for two and one fourth (2-1/4) inch springs). Cloth reinforced. Four (4) per vehicle.
Spare tire bumper
p/n: 70-0126-37
Rest pad, spare wheel cover, metal core, screw held type. Eight (8) required per car.Width: 1.75 inches. Height: 1.4375 inches.
Door weatherstrip
p/n: 20-1646-73
Weatherstrips, top of door. One strip is enough for two doors. Cut to fit as needed for all four door upper door openings. Mounts on body from approximately directly above the hinge to near the beltline of the car for the front door opening, and from beltline to beltline for the rear door opening.
Door weatherstrip
p/n: 20-1645-73
Weatherstrips, top of door. Mounts on body from approximately just above the hinge to near the beltline on the lock side of the car. Each door opening strip is made from top quality closed cell sponge rubber approximately 54 inches long.
Electrical terminal boot
p/n: 30-0279-41
Boot, electrical connection, generator terminal or ignition coil at engine.
Firewall grommet
p/n: 60-0010-45
Grommet, firewall, oblong four (4) hole style. Fits steel retainer for throttle and choke cables, oil and temperature lines.
Hood rest pad
p/n: 70-0150-42
Pad, hood rest, molded to brass core, screw mounted.Width: 1.75 inches.
Door alignment pad
p/n: 70-1821-71
Wedge pads, door aligning.Length: 1.125 inches. Width: .5 inches. Height: .875 inches.
Spare tire bumper
p/n: 70-0125-37
Rest pad, spare wheel cover, metal core, tab held type. Sixteen (16) required per car.Width: 1.75 inches. Height: .75 inches.
Steering column seal
p/n: 60-0419-36
Seal, steering column toe pan. One (1) required per car. Top quality sponge rubber, five eighths (5/8) inch thick.Width: 3.50 inches. Height: .625 inches.
Vent division bar weatherstrip
p/n: 70-1432-56
Vent window division post seal. Single approximate 32 inch strip of original cross section extruded rubber that must be cut in half to complete a pair for both the driver and passenger side door vents. To install this part, one typically uses an ad
Firewall grommet
p/n: 50-0165-20
Grommet, oval, speedometer cable through firewall.Width: 2.1875 inches.
Glovebox Door Bumper Stops
p/n: 20-1698-88
Bumper stops for the glovebox door - lower. Rubber Coated Steel like original. This part prevents the glovebox door from opening too far, reduces paint-chipping.
Starter button cover
p/n: 60-0166-21
Cover, starter pedal button. Rubber slip over type for old metal. Two (2) inch outside diameter. If car doesn't have old metal, see our #60-0322-21.
Brown steering column cushion
p/n: 60-0012-89
Grommet, steering column to cowl, for U-bolt clamp. Brown rubber. For black see our #60-0012-36.Color:brown Height: 1.25 inches.
Steering column cushion
p/n: 40-0259-36
Pad, steering post bracket. One (1) per car. Cushions steering post clamp to instrument panel.Length: 3.50 inches.
Steering column cushion
p/n: 60-0012-36
Grommet, steering column to cowl, for U-bolt clamp. Black rubber. For brown see our #60-0012-89.Height: 1.25 inches.
Battery clamp cover
p/n: 70-0095-21
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Ferrule and grommet kit
p/n: 70-0597-69
Ferrule and grommet set, outside door handle. Cadmium plated ferrule with rubber sleeve. Two (2) piece set for one (1) door.
Clutch pedal bumper
p/n: 60-0355-24
Bumper, clutch pedal shank under floorboard. Some commercial and utility models, compare with our #60-0104-24.
Hood support rod top cap
p/n: 40-0346-42
Pad, hood rest rod. For five sixteenths (5/16) inch diameter hood support rod. Also see our #40-0103-42.Length: 1.0 inches.
Door Handle Ferrule
p/n: 60-0389-69
Ferrule, outside door handle. Chrome with rubber sleeve. Two (2) piece set includes one (1) chrome piece and one (1) rubber piece. Enough for one door.
Body mounting pad
p/n: 40-0232-48
Pad, body mounting, upper. Fully molded rubber with locating collar. As many as twelve (12) used per car. One and fifteen sixteenths inch (1 15/16") outside width by two inch (2") outside width. See drawing for more dimensions.
Lower suspension arm dust seal
p/n: 70-0625-32
Dust seal, lower suspension arm bushing. Four (4) required per car.
Taillight mounting pad
p/n: 60-0122-15
Pad, taillight mounting. For high mounted taillights. (This pad was not actually used by factory. NO pad was used under these lights.
Door bumper
p/n: 20-2365-71
Kit, convertible striker bumper. Consists of four (4) bumpers for striker plates and four (4) bumpers for above and below striker.
Hood to Cowl Weatherstrip
p/n: 20-2184-42
Kit, hood to cowl weatherstrip. Forty-nine inch (49") extruded rubber strip includes installation screws.
Steering gear bushing
p/n: 40-0130-36
Bushing, insulator, for steering gear arm. Four (4) required per car.
Wiper transmission gasket
p/n: 30-0248-53
Gasket, wiper transmission mounting. One and three fourths (1-3/4) inch by two and one fourth (2-1/4) inch overall. Note: for models with Stewart Warner electric wiper transmission.
Firewall grommet
p/n: 70-0198-20
Grommet, firewall, parking brake cable, has three eighths (3/8) inch angular hole through one and one fourth (1-1/4) inch diameter grommet.
Channel filler weatherstrip
p/n: 20-1633-62
Seal, door glass and stainless frame special. Top, bottom, and sides for one door.Width: .375 inches. Height: .625 inches.
Body mounting pad
p/n: 50-0233-48
Shim, body sill.. Fully molded rubber, rectangular shaped. Two and one half inch (2 1/2") length by one and seven eighths inch (1 7/8") width by one half inch (1/2") inside hole diameter by three eighths inch (3/8") height. Buick useage for bolt location
Exhaust Support Grommet
p/n: 60-0031-13
Grommet, rear and middle muffler hanger.Height: .8125 inches.
Gearshift grommet
p/n: 20-2460-26
Repair kit, gear shift lever grommet. Column shift only. Two (2) kits required.
Body mounting pad
p/n: 70-0634-48
Pad, body mounting to frame bracket. Fully molded rubber, rectangular. Three and three sixteenths inch (3 3/16") length by two and one sixteenths inch (2 1/16") width by three fourths inch (3/4") inside hole diameter by seven sixteenths inch (7/16") heigh
Bowdrill cloth tape
p/n: 70-1172-65
Tape, black bowdrill cloth. Adhesive backed, used to create cloth cover surface for side rail weatherstrips typically. Two and one half (2-1/2) inches by five (5) foot roll. Pressure sensitive, for covering convertible side window weatherstrip such as our
Firewall grommet
p/n: 32-0196-21
Grommet, wire harness through firewall. Sheet Metal Hole: 1-5/16" Center Hole: 5/16" Outside Diameter: 1-11/16" Slot Width: 1/16"
Body mounting pad
p/n: 70-0635-48
Cushion, body mounting pad. For underside of body bracket. Fully molded rubber with locating collar. One and one half inch (1 1/2") outside diameter by eleven sixteenths inch (11/16") locating collar outside diameter by seven sixteenths inch (7/16") insid
Firewall grommet
p/n: 60-0057-21
Grommet, wiring harness through firewall, for one and one fourth (1-1/4) inch hole in sheet metal.Height: .75 inches.
Vent Window Division Bar Weatherstrip
p/n: 70-0040-56
Vent window division post seal. Extruded thirty (30") inch rubber strip that may have to be glued to your old original division post seal core, or directly to the division post.
Body mounting pad
p/n: 50-0130-48
Pad, body mounting. Fully molded rectangular rubber with locating collar. Two and one fourth inch (2 1/4") length by one and three fourths inch (1 3/4") width by thirteen sixteenths inch (13/16") locating collar outside diameter by seven sixteenths inch (
Rear coil spring pad
p/n: 50-0304-35
Insulator, rear coil spring clamp bolt (upper end). Two (2) per car. Fabric reinforced rubber as original.
Firewall grommet
p/n: 20-2279-88
Grommets, dash. Black.Ford Truck 1940 Grommets, dash. Black. Ford Cars 1938-40 Grommets, choke and throttle dash. Replacement rubber type.
Spark plug retaining ring
p/n: 30-0352-21
Retaining ring, spark plug wire. Two (2) per car.Chevrolet 1935-48 Retaining ring, spark plug wire. Two (2) per car. All models.
Axle rebound pad
p/n: 50-0303-35
Bushing, rear axle, anti-sway rod ends. Fully molded rubber. Four (4) required per car. One and three eighths inch (1 3/8") top outside diameter by one and one fourth inch (1 1/4") bottom outside diameter by three fourths inch (3/4") inside hole diameter
Body mounting pad
p/n: 70-0235-48
Pad, body mounting. Fully molded rubber with locating collar. Rectangular shaped. Three inches (3") length by two inches (2") width by fifteen sixteenths inch (15/16") locating collar outside diameter by one half inch (1/2") inside hole diameter. Three ei
Firewall grommet
p/n: 50-0299-20
Grommet, two (2) holes for oil pressure and water temperature lines through firewall.
Tan bowdrill cloth tape
p/n: 70-1173-65
Tape, brown (tan) bowdrill cloth. Adhesive backed, used to create cloth cover surface for side rail weatherstrips typically. Two and one half (2-1/2) inches by five (5) foot roll. Pressure sensitive, for covering convertible side window weatherstrip such
Antenna mount pad
p/n: 50-0168-21
Pad, antenna mounting over windshield, one and thirteen sixteenths (1-13/16) inch outside diameter, one and one fourth (1-1/4) inch inside diameter.
Body mounting pad
p/n: 40-0233-48
Pad, body mounting, lower. Fully molded rubber. One and thirteen sixteenths inch (1 13/16") outside width by one and fifteen sixteenths inch (1 15/16") outside length by one half inch (1/2") inside hole diameter by three eighths inch (3/8") height.
Lower suspension arm dust seal
p/n: 70-0624-32
Dust seal, "O" ring. Lower suspension arm pin bushing. Four (4) required per car.Height: .25 inches.
Wiper transmission gasket
p/n: 70-1198-53
Gasket, windshield wiper transmission (1939-later type). Replaces #4097038.
Door check link rod end stop
p/n: 70-0326-70
End stop and pad, door check link rod. Rubber with embedded steel plate, five sixteenths (5/16) inch diameter thread. Most models with rod type door checks.
Starter pedal bellows
p/n: 60-0210-21
Bellows, starter pedal shaft to floorboard. Three eighths (3/8) inch top hole with three (3) inch height.Width: 2.875 inches. Height: 3.0 inches.
Firewall grommet
p/n: 50-0531-20
Grommet, oil pressure, water temp, and vacuum line through firewall.